Advantech ICR-3232 User Manual
Lte industrial
Hide thumbs
Also See for ICR-3232:
- User manual (43 pages) ,
- Hardware manual (41 pages) ,
- Start manual (8 pages)
Related Manuals for Advantech ICR-3232
Summary of Contents for Advantech ICR-3232
- Page 1 LTE Industrial Router ICR-3232 USER MANUAL LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: info@lucom.de — www.lucom.de...
- Page 2 Website www.advantech-bb.com c 2020 Advantech Czech s.r.o. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photography, recording, or any information storage and retrieval system without written consent. Information in this manual is subject to change without notice, and does not represent a commitment on the part of Advantech.
- Page 3 Please see http://ep.advantech-bb.cz/devzone for more information. Advantech Czech s.r.o., Sokolska 71, 562 04 Usti nad Orlici, Czech Republic Document No. MAN-0043-EN, revision from May 19, 2020. Released in the Czech Republic. LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: info@lucom.de — www.lucom.de...
-
Page 4: Table Of Contents
ICR-3232 Contents 1 Safety Instructions 2 WEEE directive 3 Router Description 3.1 Usage of the Router ....... . . - Page 5 ICR-3232 7.5 Technical Parameters of GNSS ......7.6 Technical Parameters of WiFi ......
- Page 6 ICR-3232 List of Figures Access to the Internet from LAN ......Backed up access to the Internet .
- Page 7 ICR-3232 List of Tables Contents of package ....... . .
- Page 8 ICR-3232 1. Safety Instructions Please, observe the following instructions: The router must be used in compliance with all applicable international and national laws and in compliance with any special restrictions regulating the utilization of the router in prescribed applications and environments.
-
Page 9: Weee Directive
ICR-3232 2. Product Disposal Instructions The WEEE (Waste Electrical and Electronic Equipment: 2012/19/EU) directive was in- troduced to ensure that electrical/electronic products are recycled using the best available recovery techniques in order to minimize impact on the environment. This product contains high quality materials and components which can be recycled. -
Page 10: Router Description
ICR-3232 3. Router Description ICR-3232 is an industrial cellular router intended for the Australian market. This router is an ideal device for wireless communication in mobile networks that make use of LTE, HSPA+, UMTS, TD-SCDMA, EDGE or GPRS technology. Due to the high speed of data transfer up to 150 Mbps (download) and up to 50 Mbps (upload) is this router an ideal solution for specialized M2M devices and IoT as well as for wireless connection of traffic and security camera systems,... -
Page 11: Usage Of The Router
ICR-3232 Examples of possible applications mobile office telemetric fleet management remote monitoring security system vending and dispatcher machines telematic 3.1 Usage of the Router The router is primarily intended for these four basic situations: I. Access to the Internet from LAN Figure 1: Access to the Internet from LAN LUCOM GmbH —... -
Page 12: Backed Up Access To The Internet
ICR-3232 II. Backed up access to the Internet (from LAN) Figure 2: Backed up access to the Internet III. Secure networks interconnection or using VPN Figure 3: Using VPN tunnel LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: info@lucom.de — www.lucom.de... -
Page 13: Serial Gateway
ICR-3232 IV. Serial Gateway Figure 4: Serial Gateway LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: info@lucom.de — www.lucom.de... -
Page 14: Contents Of Package
4. Contents of Package The standard set of router includes items listed in the following table: Item# Description Figure Q’ty ICR-3232 or ICR-3232W router 1 pcs DIN holder 1 pcs (screwed on the router) Wing for wall mounting 2 pcs... -
Page 15: Router Design
ICR-3232 5. Router Design 5.1 Router Versions ICR-3232 router is supplied in the following versions (see table below). All versions are available in metal box. Router versions Version without WiFi and GNSS Version with WiFi and GNSS Table 2: Router versions... -
Page 16: Device Labels
ICR-3232 5.2 Device Labels Figure 7: Labels example 5.3 Order Codes Order codes overview is shown in the table below. Product type Product name Order code Features – interfaces ICR-3200 ICR-3232 ICR-3232 LTE module for NAM, 2x ETH, 1x BI, 1x BO,... -
Page 17: Basic Dimensions Of The Router Box (Specified In Mm)
ICR-3232 5.4 Basic Dimensions of the Router Box (specified in mm) Figure 8: Basic dimensions of the router box Figure 9: Basic dimensions of the router box LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: info@lucom.de — www.lucom.de... -
Page 18: Mounting Recommendations
ICR-3232 5.5 Mounting Recommendations Router can be placed: on a flat surface, on a wall (or other surface) using the side wings, on a DIN rail EN 60715 with the included metal DIN rail clip. For most applications with a built-in router within a switchboard it is possible to recognize... -
Page 19: Removing From The Din Rail
ICR-3232 5.6 Removing from the DIN Rail The DIN rail clip is suitable for a DIN rail according to EN 60715 standard only. The default position of metal rail clip, which is used for mounting the router on a DIN rail, is shown in the following figure. -
Page 20: Description Of The Front Panel
ICR-3232 5.7 Description of the Front Panel On the front panel of the router, there are located: Caption Connector Description — RST button used to restore the default configuration and re- boot the router 2-pin Terminal block for the power supply... -
Page 21: Status Indication
ICR-3232 5.7.1 Status Indication There are six LED indicators on the front panel to provide router status information. Each ETH port has two additional LEDs that provide information about the port status. Caption Color State Description Green Starting of the router... -
Page 22: Power Connector Pwr
ICR-3232 5.7.2 Power Connector PWR Terminal block 3.5 mm. Pin number Signal mark Description VCC(+) Positive pole of DC supply voltage (+9 to +36 V DC) GND(-) Negative pole of DC supply voltage Table 6: Connection of power connector Figure 13: Power connector Power supply for router is required between +9 V to +36 V DC supply. -
Page 23: Ethernet Port Eth0 And Eth1
ICR-3232 5.7.3 Ethernet Port ETH0 and ETH1 The panel socket of RJ45 is used for this interface. The insulation strength of Ethernet ports from each other and from the rest of the router (grounding) is 1500 V. Signal mark Description Data flow direction... -
Page 24: Ant, Div, Gnss And Wifi Antenna Connectors
ICR-3232 5.7.4 ANT, DIV, GNSS and WiFi Antenna Connectors The main and diversity antennas are connected to the router using the SMA connectors on the front panel. For the WiFi version, there are also two R-SMA connectors for connection of the WiFi antennas and one SMA connector for connection of the GNSS antenna on the right panel of the router. -
Page 25: Reset Button
ICR-3232 5.7.5 Reset Button The RST button on the front panel has three functions on ICR-3200 routers: Reboot the router: Hold the RST button for less than 4 seconds, the router will be restarted. Factory reset – restore the default configuration: Hold the RST button for more than 4 seconds. -
Page 26: Overview Of Router Reboot And Reset
ICR-3232 Action Router behavior Trigger events – options Reboot Turns off and then turns on the router Disconnect and reconnect the power Send text reboot via SMS to SIM card number put in your router (your phone number has to be authorized –... -
Page 27: Description Of The Left Panel
ICR-3232 5.8 Description of the Left Panel Interfaces located on the left panel are described in the table below. Caption Connector Description Grounding screw M3 screw Grounding screw (M3x6L) is connected to the ground of the board and to the negative pole of the power source. -
Page 28: Sim Card Reader
ICR-3232 5.8.1 SIM Card Reader Two SIM card readers for 3 V and 1.8 V SIM cards are located on the left panel of the router. In order for the router to function, it is necessary to insert an activated SIM card with an unblocked PIN code, or you can enter the PIN code in the router web interface. -
Page 29: Serial Interfaces And I/O Port
ICR-3232 5.8.2 Serial Interfaces and I/O Port The RS232 and RS485 serial interfaces together with the I/O interface are physically con- nected to the 10-pin panel socket. All three interfaces are not isolated from the router. The pinout of this conector is described in the tables below. -
Page 30: Functional Scheme Of The Binary Interface
ICR-3232 The functional scheme of connection for the binary input and binary output is drawn on the picture below. Figure 22: Functional scheme of the binary interface LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: info@lucom.de — www.lucom.de... -
Page 31: Description Of The Right Panel
ICR-3232 5.9 Description of the Right Panel Connectors located on the right panel are described in the table below. This panel has no connectors on it for the non-WiFi version of the router. Caption Connector Description WiFi2 R-SMA Connector for the second WiFi antenna. -
Page 32: First Use
ICR-3232 6. First Use 6.1 Connecting the Router Before First Use Before putting the router into operation it is necessary to connect all of the components that are required to run your applications. Don’t forget to insert a SIM card. -
Page 33: Entering Login Information
ICR-3232 By default, configuration of the router can only be performed with the default username "root". The default password is printed on the router’s label. Change the default password as soon as possible! Figure 25: Entering login information After successfully entering login information, the user will have access to the router web interface via their browser. -
Page 34: Technical Parameters
ICR-3232 7. Technical Parameters 7.1 Basic Parameters Router parameters Temperature range Operating -40 C to +75 C Storage -40 C to +85 C Humidity Operating 0 to 95 % relative humidity non condensing Storage 0 to 95 % relative humidity non condensing... -
Page 35: Standards And Regulations
ICR-3232 7.2 Standards and Regulations The router complies with the following standards and regulations: Standards and regulations Radio AS/CA S042, AS/NZC 4268 IEC 61000-6-2, IEC 61000-6-3 Safety UL/EN/AS/NZS 62368-1 Transportation EN 45545-2 National Table 15: Standards and regulations LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: info@lucom.de — www.lucom.de... -
Page 36: Type Tests And Environmental Conditions
ICR-3232 7.3 Type Tests and Environmental Conditions Phenomena Test Description Test levels EN 61000-4-2 Enclosure contact 6 kV (crit. A) Enclosure air 8 kV (crit. A) RF field AM EN 61000-4-3 Enclosure 10 V/m (crit. A) modulated (80 – 2700 MHz) 3 V/m (crit. -
Page 37: Technical Parameters Of Cellular Module
ICR-3232 7.4 Technical Parameters of Cellular Module Technical parameters of cellular module LTE parameters LTE: Cat.4, 3GPP E-UTRA Release 11 FDD frequencies: B28 (700 MHz), B5 (850 MHz), B8 (900 MHz), B4 (1700 MHz), B3 (1800 MHz), B2 (1900 MHz), B1 (2100 MHz),... -
Page 38: Technical Parameters Of Gnss
ICR-3232 7.5 Technical Parameters of GNSS GNSS specifications Antenna – active Protocols NMEA 0183 GNSS Systems GPS, GLONASS, BeiDou, Galileo, QZSS Frequency GPS/Galileo/QZSS: 1575.42 1.023 MHz GLONASS: 1597.5 – 1605.8 MHz BeiDou: 1561.1 2.046 MHz Sensitivity (autonomous) Tracking: -157 dBm... -
Page 39: Other Technical Parameters
ICR-3232 7.7 Other Technical Parameters Other technical parameters CPU power 2 DMIPS per MHz Flash memory Available memory space 1 862 MB 2x 256 MB – FW 512 MB – User data storage 838 MB – Space for User Modules... -
Page 40: Related Documents
ICR-3232 8. Related Documents Advantech Czech: Start Guide (QSG-0006-EN) Advantech Czech: ICR-3200 – Configuration Manual (MAN-0042-EN) Product related documents can be obtained on Engineering Portal at www.ep.advantech- bb.cz address. LUCOM GmbH — Flößaustr. 22a — 90763 Fürth — Tel.: +49 911/ 957 606 00 — E-Mail: info@lucom.de — www.lucom.de... -
Page 41: Troubleshooting
ICR-3232 9. Troubleshooting If you cannot connect to the router from your PC, your network card may be configured in such a way that it is not possible to connect to the router. Take one or more of the following steps in order to solve the problem: Make sure your PC’s network card is configured to obtain the IP address form the... - Page 42 ICR-3232 In a private APN it is not recommended to get the DNS settings from operator (on "Mobile WAN" page) Go to "System Log" page in "Status" section and observe where the error occurs. I cannot connect from the Internet to the device behind the router. I have NAT enabled.
- Page 43 ICR-3232 Serial communication is not working. Verify that the router model supports serial communications. Also verify the serial communication settings. To do so, open the router’s configuration menu via the web browser, select the appropriate "Expansion Port" from "Configuration" part of the menu and verify the settings.
-
Page 44: Customers Support
ICR-3232 10. Customers Support 10.1 Customer Support for NAM E-mail: support@advantech-bb.com Web: www.advantech-bb.com 10.2 Customer Support for Europe E-mail: iiotcustomerservice@advantech.eu Web: www.advantech-bb.com 10.3 Customer Support for Asia E-mail: icg.support@advantech.com.tw Web: www.advantech.com Upkeep – Advices: The SIM-card must be handled carefully as with a credit card. Don’t bend, don’t scratch on this and do not expose to static electricity.