Advertisement
OPERATION MANUAL
TEST PROBE
LP01-TOS/LP02-TOS
The LP01-TOS/LP02-TOS Test Probe is a dedicated probe for a KIKUSUI TOS6210/
TOS6200A/TOS6200/TOS6100 Earth Continuity Tester. Its convenient shape allows
faster connection to the device under test (DUT).
The LP01-TOS and LP02-TOS can measure until 30 A and 60 A respectively in the
earth continuity test.
• This product is designed to be used with a KIKUSUI Earth Continuity
NOTE
Precautions for Use
■ Be sure to connect the remote control cable.
•
Never perform testing using the Tester START switch without the remote con-
trol cable.
■ Never use the test probe with other earth continuity testers.
•
The test probe is designed specifically for use with a KIKUSUI Earth Continu-
ity Tester. It cannot be used with other earth continuity testers, even if the
connector appears to be compatible.
■ Never use the product at currents over the rated maximum current
•
The rated maximum current (see Description *1 on page 7) of the probe is 30
Aac (LP01-TOS) or 60 Aac (LP02-TOS). Use at over currents may result in
fire.
■ Never touch the contact pin immediately testing is completed.
•
If the LP02-TOS is used more than 30 A, the contact pin will be high tempera-
tures. Never touch the contact pin immediately testing is completed. Touching
will result in getting burned.
■ Handle the test probe attentively. Do not swing it around.
■ Do not yank the test probe cable or drape it over any part of your body.
Tester. Carefully read the warnings and precautions given in the Earth
Continuity Tester Operation Manual before attempting to use it.
Part No. Z1-003-490, I0027201
Oct 2020
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kikusui LP01-TOS
Summary of Contents for Kikusui LP01-TOS
- Page 1 TOS6200A/TOS6200/TOS6100 Earth Continuity Tester. Its convenient shape allows faster connection to the device under test (DUT). The LP01-TOS and LP02-TOS can measure until 30 A and 60 A respectively in the earth continuity test. • This product is designed to be used with a KIKUSUI Earth Continuity NOTE Tester.
- Page 2 Component Names and Functions Figure shows the LP02-TOS. Contact Pin Test current is delivered to this pin Holder contacting a test point of the DUT. This part holds the contact pin. START Switch This is used to begin testing. Depress the switch continuously OUTPUT LED during testing.
- Page 3 Always inspect and confirm the following items before beginning an actual test. If any abnormality or failure is found in the “Inspection Before Starting,” immediately stop using the test probe and contact your Kikusui distributor or agent for repairs. ■ Test probe cable and LOW test lead •...
- Page 4 The OUTPUT LED remains lit even when you release your finger from the START switch. • Implement measures so that no one can use the test probe until it WARNING has been repaired. • To minimize potential hazards, always contact your Kikusui distrib- utor or agent for repairs. LP01/02-TOS...
- Page 5 Connecting to the Earth Continuity Tester • Improper terminal connections can result in inaccurate measure- WARNING ments and burns or injury resulting from heat generated by con- tact resistance at the terminals. Turn off the POWER switch of the Tester. Remove the short-circuit bars connecting the OUTPUT and SAMPLING ter- minals.
- Page 6 Test Procedure • If the LP02-TOS is used more than 30 A, the contact pin will be WARNING high temperatures. Never touch the contact pin immediately test- ing is completed. Touching will result in getting burned. • Be sure to connect the contact pin and the alligator clip to the CAUTION DUT.
- Page 7 Periodic Inspection The cable of the test probe, contact pin, and LOW test lead are consumables. We recommend an annual inspection by one of service engineers. To have an inspection performed, contact your Kikusui distributor or agent. Specifications LP01-TOS LP02-TOS...
- Page 8 ○ LP02-TOS × ○ × ○ ○ ○ 本表格依据 SJ/T 11364 的规定编制。 ○ : 该部件所有均质材料的有毒有害物质的含量不超过 GB/T 26572 标准所规定的 极限值要求。 ×: 该部件至少有一种均质材料的有毒有害物质的含量超过 GB/T 26572 标准所规 定的极限值要求。 KIKUSUI ELECTRONICS CORP. 1-1-3 Higashiyamata, Tsuzuki-ku, Yokohama, 224-0023, Japan Phone: +81-45-482-6353 Facsimile: +81-45-482-6261 www.kikusui.co.jp/en/ ©2015...
Need help?
Do you have a question about the LP01-TOS and is the answer not in the manual?
Questions and answers