Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Owon PC321-TY
Summary of Contents for Owon PC321-TY
- Page 1 PC321-TY Single/3-phase Power Clamp Quick Start Guide...
-
Page 2: Safety Handling
Safety Handling WARNING: Failure to follow these safety notices could result in fire, electric shock, other injuries, or damage to the Power Clamp and other property. Read all the safety notices below before using the Power Clamp. • Avoid high humidity or extreme temperatures. • Avoid long exposure to direct sunlight or strong ultraviolet light. -
Page 3: Technical Specifications
Technical Specifications Wireless Connectivity Wi-Fi • 802.11 B/G/N20/N40 • Operating frequency: 2.4GHz RF Characteristics • Internal Antenna Physical Specifications Operating Voltage • 100~240 Vac 50/60 Hz • ≤ 100W ( Within ±2W ) Calibrated Metering Accuracy • >100W ( Within ±2% ) • CT 80A (default) CT Provided • CT 120A/200A/300A(optional) • Temperature: -20 ℃... - Page 4 Welcome PC321-TY Power Clamp helps you monitor the amount of electricity usage in your facility by connecting the clamp on to the power cable. It can also measure Voltage, Current, PowerFactor, ActivePower. This guide will provide you with an overview of the product and help you get through the initial setup to installation.
-
Page 5: Get To Know Your Device
Get to know your device LED indicator CT: Current Transformer Cable AC Input cable Clamp... -
Page 6: Led Indicator
Reset Button Reset Button • Reset. Press and hold the reset button for 5 seconds until the LED indicator flashes 3 times quikly to restore the power clamp to default factory settings (energy data will be cleared). And it will get into EZ mode for 3 minutes. -
Page 7: Important Safety Information
Installaion Important safety information! • The power clamp must be installed and serviced only by a qualified electrical personnel. • Do not touch the terminals of the device during testing. • Turn off all the power supply for this equipment before installing. • Make sure that the power supply is off before connecting or disconnecting it to an auxiliary device. - Page 8 PC321 Load1 Load2 Load3 Red/L1 Green/L2 Brown/L3 White/N L3/C L2/B L1/A Circuit Breaker Single Phase electricity wiring diagram Follow the steps below: 1. Connect AC Input cable to a socket near the Electrical Box to power on the Power Clamp according to the corresponding phase wiring diagram.
-
Page 9: Configure Network
Tips about the clamp: • Cable diameter does not affect usage as long as the cable can pass through the clamp hole. • The meter has three clamps which can be applied to cable devices for separate measurement. If applied to the same cable, all clamps will produce the same reading. -
Page 10: Add Devices
4.2 Add devices 1. Open your App. 2. Login with an existing account. If you are a new user, you need to create an account at first. 3. Please click the '+' button at the top right corner of the App to add devices. - Page 11 6. Place the router, mobile phone and Power Clamp as close as possible to wait for connection. Confirm the green indicator on your device is rapidly blink, then tap 'Next'. 7. After the connection succeeds, you can rename the it and click "Done"...
- Page 12 Mounting The Power Clamp has a mounting bracket for mounting purposes. 1. Use the mounting bracket as template to mark the two holes on the wall for installing screws. 2. Screw the mounting bracket onto the wall according to marked location.
- Page 13 3. Place the router, mobile phone and Power Clamp as close as possible. Confirm the indicator on your device is slowly blink, then tap 'Next' to wait for connection. 4. Find and connect the device's hotspot in the Wi-Fi list.
- Page 14 5. After the connection succeeds, you can rename it and click 'Done' to complete the configuration. (If failed, please refer to FAQ3 to troubleshoot) 2. How to identify the Power Clamp is powered on? 1. You can press the reset button once, if the LED indicator flashes red 3 times, which means the device is powered on.
- Page 15 - If you have already upgrate the iOS system to 14, you need to enable the 'Local network' of the App. - If it still does not work, it is recommended to change the router and try again. 4. Device offline - Confirm whether the Power Clamp is powered on.
Need help?
Do you have a question about the PC321-TY and is the answer not in the manual?
Questions and answers