Advertisement
Quick Links
Made in Vietnam
Model No: 110444
Distributed in the U.S.A by:
Restoration Hardware baby & child
11640 Harrel St. Suite B
Mira Loma, CA 91752
rh babyandchild .com
Destributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
WARNING:
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by
writing to the address above. Include the product model number, color, and a brief description of the part. Call
1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a soft, dry
cloth. Blot spills immediately and wipe with a clean, damp cloth. If the crib is to be stored, store in a cool, dry
place and carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included).
Note: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of a turn. After crib is
completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly.
RHBABY&CHILD
Tanner Conversion Crib
Read all
Page 1 of 11
V2.1
Advertisement
Related Manuals for RH Baby&child 110444
Summary of Contents for RH Baby&child 110444
- Page 1 V2.1 RHBABY&CHILD Tanner Conversion Crib Made in Vietnam Model No: 110444 Distributed in the U.S.A by: Restoration Hardware baby & child 11640 Harrel St. Suite B Mira Loma, CA 91752 rh babyandchild .com Destributed in Canada by: Restoration Hardware Canada, Inc.
- Page 2 V2.1 RHBABY&CHILD Tanner Conversion Crib IMPORTANT SAFETY INFORMATION FOR CRIBS WARNING: Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an infant. WARNING: Failure to follow these warnings and the assembly instructions could result in serious injury or death. ■...
- Page 3 V2.1 RHBABY&CHILD Tanner Conversion Crib IMPORTANT SAFETY INFORMATION FOR CRIBS CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4 INCHES BY 51 5/8 INCHES WITH A THICKNESS NOT EXCEEDING 6 INCHES. WARNING ■ Do not use this crib if the enclosed or attached instructions cannot be strictly adhered to.
- Page 4 V2.1 RHBABY&CHILD Tanner Conversion Crib IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS A WARNING: ENTRAPMENT/STRANGULATION HAZARD Infants have died in toddler beds from entrapment and strangulation. Failure to follow these warnings and the assembly instructions could result in serious injury or death. NEVER use bed with children under 15 months.
- Page 5 V2.1 RHBABY&CHILD Tanner Conversion Crib PARTS INCLUDED ITE M DESCRIP TION QUANTITY A [1] HEADBOARD Pin Bolt B [1] FRONT RAIL 4 pcs. ¾"x2¼"x1 3/J6"h C [1] LH SIDE FRAME D [1] RH SIDE FRAME Allen Nut 4 pcs. ¾•x½• E [1] MATTRESS PLATFORM Allen Bolt ASSEMBLY INSTRUCTIONS...
- Page 6 V2.1 RHBABY&CHILD Tanner Conversion Crib STEP 2: Insert the Pin Bolts (1) to the side frames as shown in the sketch. There are three height adjustments for choice. Align the holes and position the Mattress Platform (E) onto the Pin Bolts. Note: Mattress platform is easily adjustable to varying heights by loosening and removing the Pin Bolt (1) from all four corners and reinserting into a different hole for a higher or lower level.
- Page 7 V2.1 RHBABY&CHILD Tanner Conversion Crib STEP 3: Insert the Allen Nuts (2) and tighten using Allen Key (5). Set the Mattress Platform (E) to the desired height by adjusting the Pin Bolts (1). The Mattress Platform should be at its highest setting for newborns, then adjusted to the lower positions as the child grows and becomes mobile. Once the child is able to stand, the Mattress Platform should be at its lowest position.
- Page 8 V2.1 RHBABY&CHILD Tanner Conversion Crib STEP4: Repeat steps 2 and 3 to connect the Front Rail (B) as shown in the sketch. ¼ • (3) 1k' x 2 Allen Bolt = 4 pcs (4) Lock Washer = 4 pcs (Q)� (5) Allen Key ---j Page 8 of 11...
- Page 9 V2.1 RHBABY&CHILD Tanner Conversion Crib STEPS: In order to convert the crib to a toddler bed, loosen all tightened bolts from side frames. Spread front of crib open enough to remove Front Rail (B) and to insert toddler rail (sold separately) between crib side frames. Note: If Mattress Platform (E) is not in the lowest position, unscrew Allen Nuts (2) and move it to the lowest position.
- Page 10 V2.1 RHBABY&CHILD Tanner Conversion Crib STEP 6: Repeat step 3 to connect the toddler rail as shown in the sketch. When converting the crib to a toddler bed, the Allen Bolts (6) should be inserted in the upper holes of the side frames and tightened with the Allen Key (5). (6) 1/,6"...
- Page 11 V2.1 RHBABY&CHILD Tanner Conversion Crib STEP 7: The crib can be converted to a full size bed. Using the Headboard (A), attach a full size bed frame (sold separately) at the location shown. Insert the Flat Washer (9) and Small Lock Washer (8) onto the Allen Bolt (7) and tighten using Small Allen Key (10).
Need help?
Do you have a question about the 110444 and is the answer not in the manual?
Questions and answers