Mitsubishi Electric MELSEC FX0N-8EX-UA1/UL Hardware Manual page 13

FX2N Series Programmable Controllers
LVD
The following products have shown compliance through direct testing (of the identified standards below) and design
analysis (through the creation of a technical construction file) to the European Directive for Low Voltage (73/23/EEC) when
used as directed by the appropriate documentation.
Refer to a manual or related material of each product other than the following.
Type : Programmable Controller (Open Type Equipment)
Models : MELSEC FX
from July 1st, 1997
from April 1st, 1998
from August 1st, 1998
from August 1st, 2005
For the products above, PLCs manufactured
before March 31st, 2002 are compliant with IEC1010-1
from April 1st, 2002 to April 30th, 2006 are compliant with EN61131-2:1994+A11:1996+A12:2000
after May 1st, 2006 are compliant with EN61131-2:2003
IEC1010-1:1990
/A1:1992
EN61131-2:1994
/A11:1996
/A12:2000
EN61131-2:2003
Models : MELSEC FX
from November 1st, 1995
from February 1st, 1996
from April 1st, 1996
from July 1st, 1996
IEC1010-1:1990
/A1:1992
/A2:1995
BSEN61010-1 :1993 *
/A2:1995
* Compliance to BSEN61010-1 and Amendment2 is claimed through virtue of direct compliance to IEC1010-1,
Amendment 1 and Amendment 2.
series manufactured
2N
FX
2N
Where
FX
2N
Where
FX
2N
FX
2N
Where
FX
2N
FX
2N
Where
FX
2N
FX
2N
Standard
Safety requirements for electrical
equipment for measurement, control,
and laboratory use
- General requirements
Programmable controllers
- Equipment requirements and tests
Programmable controllers
- Equipment requirements and tests
series manufactured
0N
FX
0N
FX
0N
FX
0N
FX
0N
Harmonized Products
FX
0N
FX
0N
Standard
Safety requirements for electrical
equipment for measurement, control,
and laboratory use
- MR-ES/UL FX
indicates:16,32,48,64,80,128
- ER-ES/UL FX
indicates:32,48
-16EYR-ES/UL
- MR-DS
indicates:32,48,64,80
-48ER-DS
- MR-UA1/UL
indicates:16,32,48,64
-16MR-DS FX
-8ER-ES/UL FX
The equipment has been assessed as a component for fitting
in a suitable enclosure which meets the requirements of
IEC 1010-1:1990+A1:1992
The equipment has been assessed as a component for fitting
in a suitable enclosure which meets the requirements of
EN61131-2:1994+A11:1996+A12:2000
The equipment has been assessed as a component for fitting
in a suitable enclosure which meets the requirements of
EN61131-2:2003
-8EX-ES, FX -8EYR-ES, FX
0N
-8ER-ES, FX -16EX-ES, FX
0N
-8ER-ES/UL, FX -16EX-ES/UL, FX
0N
-16EYT-ESS/UL
-8EX-ES/UL,
-8EYR-ES/UL, FX -8EYT-ESS/UL
0N
The equipment has been assessed as a component for
fitting in a suitable enclosure which meets the
requirements of IEC 1010-1:1990,A1:1992 and
A2:1995(BSEN61010-1 :1993 and A2:1995)
- MT-ESS/UL
2N
- ET-ESS/UL
2N
-48ER-UA1/UL
2N
-8EYR-ES/UL
2N
Remark
-8EYT-ESS
0N
-16EYR-ES, FX -16EYT-ESS
0N 0N
-16EYR-ES/UL,
0N
Remark
Standards
xi