Mitsubishi Electric MELSEC FX0N-8EX-UA1/UL Hardware Manual page 11

FX2N Series Programmable Controllers
Note Concerning the CE Marking
This document does not guarantee that a mechanical system including this product will comply with the following
standards. Compliance to EMC directive and LVD directive of the entire mechanical system should be checked by the user
/ manufacturer. For more details please contact the local Mitsubishi Electric sales site.
Programmable logic controllers are open-type devices that must be installed and used within conductive control boxes.
Please use the FX
Please secure the control box lid to the control box (for conduction).
Installation within a control box greatly affects the safety of the system and aids in shielding noise from the programmable
logic controller.
EMC
The following products have shown compliance through direct testing (of the identified standards below) and design
analysis (through the creation of a technical construction file) to the European Directive for Electromagnetic Compatibility
(89/336/EEC) when used as directed by the appropriate documentation.
Refer to a manual or related material of each product other than the following.
Type : Programmable Controller (Open Type Equipment)
Models : MELSEC FX
from July 1st, 1997
from April 1st, 1998
from August 1st, 1998
from July 1st, 2001
from August 1st, 2005
For the products above, PLCs manufactured
before March 31st, 2002 are compliant with EN50081-2 (EN61000-6-4) and EN50082-2
from April 1st, 2002 to April 30th, 2006 are compliant with EN50081-2 (EN61000-6-4) and EN61131-
2:1994+A11:1996+A12:2000
after May 1st, 2006 are compliant with EN61131-2:2003
EN50081-2:1993
EN61000-6-4:2007 - Generic emission standard
EN50082-2:1995
EN61131-2:1994
/A11:1996
/A12:2000
EN61131-2:2003
Series programmable logic controllers while installed in conductive shielded control boxes.
2N
series manufactured
2N
FX
Where
FX
Where
FX
FX
FX
FX
Where
FX
FX
FX
FX
FX
FX
Standard
Electromagnetic compatibility
Industrial environment
Electromagnetic compatibility
- Generic immunity standard
Industrial environment
Programmable controllers
- Equipment requirements and tests
Programmable controllers
- Equipment requirements and tests
- MR-ES/UL
2N
indicates:16,32,48,64,80,128
- ER-ES/UL
2N
indicates:32,48
-16EX-ES/UL FX -16EYR-ES/UL FX
2N 2N
-232-BD FX -485-BD
2N 2N
-8AV-BD FX -CNV-BD
2N 2N
- MR-DS
2N
indicates:32,48,64,80
-48ER-DS
2N
- MR-UA1/UL Where
2N
-16MR-DS FX
2N 2N
-ROM-E1
2N
-8ER-ES/UL FX -8EX-ES/UL
2N 2N
-8EYR-ES/UL FX -8EYT-ESS/UL
2N 2N
Compliance with all relevant aspects of the standard.
(Radiated Emissions and Mains Terminal Voltage Emissions)
Compliance with all relevant aspects of the standard.
(RF immunity, Fast Transients, ESD, Conducted and Power
magnetic fields)
Compliance with all relevant aspects of the standard.
(RF Immunity, Fast Transients, ESD and Damped oscillatory
wave)
Compliance with all relevant aspects of the standard.
(Radiated Emissions, Mains Terminal Voltage Emissions, RF
Immunity, Fast Transients, ESD, Surge, Voltage drops and
interruptions, Conducted and Power magnetic fields)
FX - MT-ESS/UL
2N
FX - ET-ESS/UL
2N
-16EYT-ESS/UL
2N
FX -422-BD
2N
FX -CNV-IF
2N
FX - MT-DSS
2N
FX -48ET-DSS
2N
indicates:16,32,48,64
-16MT-DSS FX -48ER-UA1/UL
2N
Remark
Standards
ix