Advertisement
Installing the Camera
ATTENTION:
Test the camera prior to selecting a permanent
mounting location by temporarily connecting the
camera(s) and cables to the DVR.
To install the camera:
1. Use the included mounting template to mark and drill
holes for the included mounting screws.
NOTE:
Insert the included drywall anchors if installing into
drywall.
2. Connect the video and power cable as detailed in the
section 'Setting up the Camera'.
3. Attach the camera
base to the mouting
surface using the
included screws.
4. Set the position and angle of the camera using the
provided Allen key.
A
B
A) Turn the adjustment ring
B) Loosen lower screw with
to tighten / loosen the stand
the Allen key to adjust the
connection. Adjust the
camera's vertical position.
camera's horizontal position.
C
C) Loosen upper screw with the
Allen key to rotate the camera
housing.
5. Remove the protective film from the camera lens.
Setting up the Camera
1. Connect one of the two BNC connectors on the camera to
the video cable. See "Camera Wiring" for details.
2. DC Power—Power Pigtail: Connect the included power
pigtail to the camera. Connect the terminating wires of the
cable directly to the DC power source.
OR
3. DC Power—Power Adapter: Connect a 12V DC power adapter
(not included) to the camera and a local power outlet.
NOTE:
For pigtail connection with 12V DC, make sure to check
polarity specifications on the power adapter.
WARNING:
A REGULATED 12V DC power supply is REQUIRED for use with
this camera. Use of a non-regulated, non-conforming power
supply can damage this product and voids the warranty.
Camera Wiring
Connect to the included
power pigtail or a 12V
DC power adapter
(not included).*
Analog
MPX
MPX
Analog
Connect to an MPX
Connect to an analog
DVR for 1080p viewing
DVR for 960H viewing
and recording.
and recording.
* Camera focus may be affected if the power connection is too
long. It is recommended not to extend the power connection
past 200ft (61m).
Extension Cable Options
The entire length of the cable run must be made using a
single extension cable between the camera and the DVR.
Specification
Maximum Length
RG59 20AWG Conductor 95% Braid
Up to 1000ft (300m)
CSA/UL or C(UL) Approved
RG6 20AWG Conductor 95% Braid
Up to 2000ft (600m)
CSA/UL or C(UL) Approved
Analog CCTV Balun
Up to 300ft (91m)
† Long cable runs over 1000ft (300m) may be affected by
electro-mechanical interference (EMI), which can increase the
amount of noise in the picture in some installations.
Camera Specifications
Image Sensor
Video Format
Effective Pixels
Resolution
Scan System
Sync System
S / N Ratio
Iris
AES Shutter Speed
Min. Illumination
Video Output
Lens Focal Length / Type
FOV (Horizontal)
Termination
IR Range / Qty.
Power Requirement
Power Consumption
Operating Temp. Range
Environmental Rating
Dimensions (W x H x D)
Weight (including stand)
Camera Dimensions
2.8"
†
72mm
†
2.8"
72mm
1/3" 2.1MP CMOS
NTSC (C233BD)/PAL (C233BDP)
H: 1920 V: 1080
Digital: 1080p
Analog: 960H
Progressive
Internal
≥ 50dB (AGC Off)
AES
1/60 (1/50) ~ 1/60,000 sec.
0.1 LUX (IR Off)
0 LUX (IR LEDs On)
Digital: 1080p MPX HD-CVI
Analog: Composite 1.0Vpp @
75ohm
3.6mm F2.0 / Fixed
MPX: 88°
960H: 82°
BNC Type
70ft / 21m; 24 IR LED's
12V DC ± 10%
380mA MAX with IR LED
–22° ~ 140°F / –30° ~ 60°C
IP66
2.8" x 2.8" x 8.0"
72mm x 72mm x 204mm
0.9lbs / 0.4kg
8.0"
204mm
Advertisement
