Related Manuals for Golden Tornado 8-CYLINDER
Summary of Contents for Golden Tornado 8-CYLINDER
- Page 1 INSTALLATION MANUAL MODEL: 8-CYLINDER 17611 East St, North Fort Myers, FL 33917 (239) 337-4141 REVISION A GoldenMarineSystems.com GoldenBoatLifts.com PUBLISHED 7/15/2020...
-
Page 2: Table Of Contents
REFERENCE NOTES ................23 enclosed within fiberglass lock box (Operated using provided transmitters) INTRODUCTION FEATURES Golden is proud to introduce the Tornado Lift to our line of • Hardened Stainless Axles with Nylatron Sleeves. lifts. • Highest Lift Travel at 6’ of Rise •... -
Page 3: Safety Requirements
GOLDEN BOAT LIFTS. WARNING Note: Any installation or operation methods outside the... -
Page 5: Part/Hardware Identification Table
OPT PART IDENTIFICATION HARDWARE IDENTIFICATION (16) 1/8” (32) Stern Side H-Frame Lower Cylinder Mount Hinge Bearing Cotter Pin (66”) 1/2” (58) 1" (16) 3/8” (72) Cross Beam Lock Washer Bow Side H-Frame Hinge Pin (64”) (16) 1/2” (58) 3/8” (72) Hydraulic Cylinder Aluminum Multi-Bunk Hex Nut... -
Page 6: General Assembly
PARTS REQUIRED TO MOUNT CROSSBEAM Side Beam (2) Leg Pocket Crossbeam (2) MOUNT CROSSBEAMS 3/8” Flat Washer (24) 3/8” Lock Washer (12) Note: Cross Beams will ship with leg pockets pre-assembled. Note: Ensure Crossbeam and Leg Pocket is oriented in the upward position as shown in Figure 1. -
Page 7: Attach Foot Pad
ATTACH FOOT PADS PARTS REQUIRED TO ATTATCH FOOT PAD Note: The Foot Pad(s) referenced in this step is an optional part purchased with the Tornado Boat Lift. If the Foot Pad part was not ordered and included, you may skip to the next step. Foot Pad (6) Square Tube Leg (6) Note: Four (4) out of six (4) Square Tube Legs will be attached to... -
Page 8: Mount Side Beam
MOUNT SIDE BEAMS** PARTS REQUIRED TO MOUNT SIDE BEAM Note: Ensure Side Beam Saddle is positioned so that open end of saddle is facing downward during installation shown in Figure 5. Slide the Side Beam Saddle down over the Cross Beam as shown in Figure 5. -
Page 9: Attach Lower Cylinder Mount
PARTS REQUIRED TO MOUNT LOWER ATTACH LOWER CYLINDER MOUNT** CYLINDER MOUNT Note: Ensure lower Cylinder Mount is between both Side Beams when mounting. Align the holes on the Lower Cylinder Mount with the corresponding holes on the Side Beam as shown in figure 6. Attach one (1) 1/2”... -
Page 10: Attach Inner Foot Pads
ATTACH INNER FOOT PADS** PARTS REQUIRED TO ATTACH INNER FOOT PAD(S) Note: Please use the two (2) Foot Pad & Square Tube Leg assemblies prepared in previous step. Slide the Square Tub Leg into the Middle Leg Support and align the mounting holes at desired height as shown in Middle Leg Support (2) Figure 7. -
Page 11: Mount Stern Side H-Frame
MOUNT STERN SIDE H-FRAME PARTS REQUIRED TO MOUNT STERN SIDE H-FRAME Note: For this step, ensure the Stern Side H-Frame is being used. Note: Hinge Bushings are preinstalled on Side Beam. Align the mounting holes on the Stern Side H-Frame hinge plate with the Hinge Bushings located on the Side Beam as shown in Figure 10. -
Page 12: Mount Bow Side H-Frame
MOUNT BOW SIDE H-FRAME PARTS REQUIRED TO MOUNT BOW SIDE H- FRAME Note: For this step, ensure the Bow Side H-Frame is being used. Note: Hinge Bushings are preinstalled on Side Beam. Align the mounting holes on the Bow Side H-Frame hinge plate with the Hinge Bushings located on the Side Beam as shown in Figure 12. -
Page 13: Mount Middle H-Frame
MOUNT MIDDLE H-FRAME PARTS REQUIRED TO MOUNT MIDDLE H- FRAME Note: For this step, ensure both Middle H-Frames are being used. Note: Ensure the smaller Middle H-Frame (64-7/8”) is mounted closer to the Bow Side H-Frame and the larger Middle H-Frame (65-1/2”) is mounted closer to the Stern Side H-Frame. -
Page 14: Mount Hydraulic Cylinder
MOUNT HYDRAULIC CYLINDER PARTS REQUIRED TO MOUNT HYDRAULIC CYLINDER(S) Note: Ensure Hydraulic Cylinder is oriented so that the lower mounting hole is facing downward. Align the lower Hydraulic Cylinder mounting hole with the corresponding holes on the Lower Cylinder Mount as shown in Figure 13. - Page 15 MOUNT HYDRAULIC CYLINDER(S) PARTS REQUIRED TO MOUNT HYDRAULIC CYLINDER(S) cont. Note: Ensure Hydraulic Cylinder(s) are tightly fastened as described in previous step before continuing. Align the upper Hydraulic Cylinder mounting hole with the Hydraulic Cylinder (8) corresponding holes on the H-Frame as shown in Figure 14 &...
-
Page 16: Mount V-Bunk Support
MOUNT V-BUNK SUPPORT PARTS REQUIRED TO MOUNT V-BUNK SUPPORT Align the 1” holes of the H-Frame(s) with the corresponding holes on the V-Bunk Support, resting the V-Bunk Support on top of the H-Frame(s) as shown in Figure 16. Insert one (1) 1/8” Cotter Pin into one (1) 1” Hinge Pin, bending the tines of the Cotter Pin outward and apart, securing the Cotter Pin within the Hinge Pin. -
Page 17: Attach V-Bunk
ATTACH V-BUNK** PARTS REQUIRED TO MOUNT V-BUNK Align the bracket of the V-Bunk so it is resting on top of the V-Bunk Support. Attach one (1) 3/8” Flat Washer to two (2) 3/8” Hex Bolts and insert the Hex Bolts into the corresponding holes on the V- Bunk as shown in Figure 18. -
Page 18: Attach V-Bunk Bracket
ATTACH V-BUNK BRACKET** PARTS REQUIRED TO MOUNT V-BUNK BRACKET Align the 1/2” holes of the V-Bunk Brackets so that they are above and below the V-Bunk arm as shown in Figure 20. Attach one (1) 1/2" Flat Washer over two (2) 1/2" Hex Bolts and insert them into the corresponding holes as shown in Figure 20. -
Page 19: Mount Aluminum Multi-Bunk
Note: Before proceeding to the following steps, please revisit PARTS REQUIRED TO MOUNT ALUMINUM steps with asterisks and use a wrench to tighten all hardware MULTI-BUNK that was originally hand tightened. Failure to tighten all hardware as described can cause damage to the Tornado Boat Lift and/or serious injury/death. -
Page 20: Attach Guide Pole Mounting Bracket
ATTACH GUIDE POLE MOUNTING PARTS REQUIRED TO INSTALL GUIDE POLE MOUNTING BRACKET BRACKET(S) Note: The Guide Pole Mounting Bracket referenced in this step are optional parts purchased with the Tornado Boat Lift. If the Guide Pole Mounting Bracket part was not ordered and included, you may skip this and the following step. -
Page 21: Attach Guide Pole
ATTACH GUIDE POLE(S) PARTS REQUIRED TO INSTALL GUIDE POLE Note: The Guide Poles referenced in this step are optional parts purchased with the Tornado Boat Lift. If the Guide Pole part was not ordered and included, you are finished with the Tornado Boat Lift installation. - Page 22 Note: Before launching the Tornado Lift, please reference the Slowly lift the boat upward, pausing every 6” to ensure HYDRAULIC POWER PACK INSTALLATION MANUAL provided to the lift is staying level. Continue this process until the continue installation of the power supply for the Tornado boat is fully lifted out of the water.
-
Page 23: Safety Requirements
REFERENCE NOTES Tornado Boat Lift (4-Cylinder) Capacity: 24K INSTALLATION PROVIDER: ___________________________________________________ INSTALLATION DATE: _________________________ INSTALLATION ADDRESS: _______________________________________________________________________________________________________ INSTALLATION CHECKLIST: STEP DATE/TIME INITIAL NOTES SAFETY REQUIREMENTS PART/HARDWARE IDENTIFICATION TABLE MOUNT CROSS BEAM ATTACH FOOT PAD MOUNT SIDE BEAM ATTACH LOWER CYLINDER MOUNT ATTACH INNER FOOT PADS MOUNT STERN SIDE H-FRAME MOUNT BOW SIDE H-FRAME...