Page 1
INSTALLATION MANUAL MODEL: 1-CYLINDER 17611 East St, North Fort Myers, FL 33917 (239) 337-4141 REVISION A GoldenMarineSystems.com GoldenBoatLifts.com PUBLISHED 7/15/2020...
INTRODUCTION (1.4 m – 3 m) • FRAME SIZE ≈ 96 in x 72 in [L x W] Golden is proud to introduce the Tornado Lift to our line of (2.44 m x 1.83 m) lifts. • BUNK LENGTH ≈ 96 in (2.44 m) •...
PARTS REQUIRED TO MOUNT CROSSBEAM Leg Pocket Crossbeam (2) MOUNT CROSSBEAMS 3/8” Flat Washer (16) 3/8” Lock Washer (8) Note: The Square Tube Leg(s) referenced in this step is an optional part purchased with the Tornado Boat Lift. If the Square Tube Leg part was not ordered and included, you may skip to the next step.
ATTACH FOOT PADS PARTS REQUIRED TO ATTATCH FOOT PAD Note: The Foot Pad(s) referenced in this step is an optional part purchased with the Tornado Boat Lift. If the Foot Pad part was not ordered and included, you may skip to the next step. Foot Pad (4) Square Tube Leg (4) Attach one (1) Foot Pad to the end of one (1) Square Tube Leg...
MOUNT SIDE BEAMS** PARTS REQUIRED TO MOUNT SIDE BEAM Note: Ensure Side Beam Saddle is positioned so that open end of saddle is facing downward during installation shown in Figure 5. Place the Side Beam Saddle down over the Cross Beam as shown in Figure 5.
PARTS REQUIRED TO MOUNT LOWER ATTACH LOWER CYLINDER MOUNT** CYLINDER MOUNT Note: Ensure lower Cylinder Mount is between both Side beams when mounting. Align the holes on the Lower Cylinder Mount with the corresponding holes on the Side Beam as shown in figure 6. Attach one (1) 1/2”...
MOUNT STERN SIDE H-FRAME PARTS REQUIRED TO MOUNT STERN SIDE H-FRAME Note: For this step, ensure the Stern Side H-Frame is being used. Note: Hinge Bushings are preinstalled on Side Beam. Align the mounting holes on the Stern Side H-Frame hinge plate with the Hinge Bushings located on the Side Beam as shown in Figure 8.
MOUNT BOW SIDE H-FRAME PARTS REQUIRED TO MOUNT BOW SIDE H- FRAME Note: For this step, ensure the Bow Side H-Frame is being used. Note: Hinge Bushings are preinstalled on Side Beam. Align the mounting holes on the Bow Side H-Frame hinge plate with the Hinge Bushings located on the Side Beam as shown in Figure 10.
MOUNT HYDRAULIC CYLINDER PARTS REQUIRED TO MOUNT HYDRAULIC CYLINDER Note: Ensure Hydraulic Cylinder is oriented so that the lower mounting hole is facing downward. Align the lower Hydraulic Cylinder mounting hole with the corresponding holes on the Lower Cylinder Mount as shown in Figure 11.
Page 13
MOUNT HYDRAULIC CYLINDER cont. PARTS REQUIRED TO MOUNT HYDRAULIC CYLINDER Note: Ensure Hydraulic Cylinder(s) are tightly fastened as described in previous step before continuing. Align the upper Hydraulic Cylinder mounting hole with the corresponding holes on the H-Frame as shown in Figure 12 &...
Note: Before proceeding to the following steps, please revisit PARTS REQUIRED TO MOUNT ALUMINUM steps with asterisks (Pgs. 8 & 9) ) and use a wrench to tighten all MULTI-BUNK hardware that was originally hand tightened. Failure to tighten all hardware as described can cause damage to the Tornado Boat Lift and/or serious injury/death.
ATTACH GUIDE POLE MOUNTING PARTS REQUIRED TO INSTALL GUIDE POLE MOUNTING BRACKET BRACKET(S) Note: The Guide Pole Mounting Bracket referenced in this step are optional parts purchased with the Tornado Boat Lift. If the Guide Pole Mounting Bracket part was not ordered and included, you may skip this and the following step.
ATTACH GUIDE POLE(S) PARTS REQUIRED TO INSTALL GUIDE POLE Note: The Guide Poles referenced in this step are optional parts purchased with the Tornado Boat Lift. If the Guide Pole part was not ordered and included, you are finished with the Tornado Boat Lift installation.