Advertisement
Quick Links
Advertisement
Related Manuals for fantastic furniture HAVANA Bookcase
Summary of Contents for fantastic furniture HAVANA Bookcase
- Page 1 Version 1.0 TWO PEOPLE HAVANA Bookcase REQUIRED www.fantasticfurniture.com.au...
- Page 2 Recommended weight capacity : 10KG/Shelf. WARNING: ENSURE THE WALL STRAP IS ATTACHED TO AVOID SERIOUS INJURY. To avoid any serious or fatal injury, this product has been supplied with a wall strap to prevent toppling. We strongly recommend that this product is permanently fixed to the wall or other suitable surface.
-
Page 3: Assembly Checklist
Assembly checklist Read through the instructions carefully Make sure you have all the required tools. before you begin. Never use power tools unless instructed. Identify and lay out all of the components Unless instructed, do not fully tighten screws before you begin assembly. until the item is fully assembled. -
Page 4: What You Need
What you need Right Leg (P4) Top Panel (P1) to assemble the product Right Leg (P4) Divider Panel (P5) DO NOT USE Shelf Top Shelf Middle Side Panel (P7) Panel (P6) Additional Tools Required Panel Phillips head screwdriver; (P10) Hammer Shelf Bottom Small Shelf Panel (P8) - Page 5 Step 1 You will need (P4) 16 x Cam Bolts Phillips head (H3) screwdriver (P3) Secure 4 x Cam Bolts (H3) to each Left Leg (P3x2) and 4 x Cam Bolts (H3) to each Right Leg (P4x2) by tightening Cam Bolts (H3) with a Phillips Head Screwdriver. Step 2 You will need (P1)
- Page 6 Step 3 You will need (P6) 16 x Cam Bolts Phillips head (H3) screwdriver (P7) (P8) Secure 2 x Cam Bolts (H3) to each Shelf Middle Panel (P6x2), 2 x Cam Bolts (H3) to each Shelf Bottom Panel (P8x2) and 4 x Cam Bolts (H3) to Shelf Top Panel (P7) by tightening Cam Bolts (H3) with a Phillips Head Screwdriver.
- Page 7 Step 5 You will need (P7) 8 x Dowels 8 x Cam Nuts (H1) (H4) (P10) Phillips head screwdriver This is how a cam nut works ..The head of the cam (P6) bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over the bolt.
- Page 8 Step 7 You will need 2 x Dowels 2 x Cam Nuts (H1) (H4) (P8) (P6) Phillips head (P5) screwdriver (P10) (P8) Insert 2 x Dowels (H1) into Divider Panel (P5) then attach to Shelf Bottom Panel (P8). Insert 2 x Cam Nuts (H4) into Divider Panel (P5). Ensure the arrows on the cam nuts are facing towards the incoming cam bolts and secure by tightening cam nuts with a Phillips Head Screwdriver.
- Page 9 Step 9 You will need 2 x Dowels 2 x Cam Nuts (H1) (H4) Phillips head screwdriver (P8) (P5) Insert 2 x Dowels (H1) into Divider Panel (P5) then attach to Shelf Bottom Panel (P8). Insert 2 x Cam Nuts (H4) into Divider Panel (P5). Ensure the arrows on the cam nuts are facing towards the incoming cam bolts and secure by tightening cam nuts with a Phillips Head Screwdriver.
- Page 10 Step 11 (P4) You will need (P3) 16 x Dowels 8 x Cam Nuts (P7) (H1) (H4) (P8) (P9) (P9) Phillips head (P7) screwdriver TWO PEOPLE (P2) (P8) REQUIRED Insert 8 x Dowels (H1) into Left Leg (P3) and 8 x Dowels (H1) into Right Leg (P4).
- Page 11 Step 13 You will need (P1) 10 x Dowels 4 x Bolts (H1) (H2) (P5) 2 x Cam Nuts 1 x Allen key (P3) (H4) (H6) (P4) (P3) Insert 10 x Dowels (H1) into Top Panel (P1) then attach to Left & Right Legs (P3x2&P4x2) as shown.
-
Page 12: Job Complete
Step 15 (P1) You will need 1 x Safety 1 x Safety Strap Strap (H9) Screw (H10) 1 x Washer (H11) Secure the Safety Strap (H9) to the Top Panel (P1) with 1 x Washer (H11) and 1 x Safety Strap Screw (H10) by tightening with the Phillips Head Screwdriver.