Ikelite DS160 Manual
Strobe
Hide thumbs
Also See for DS160:
- Instructions manual (24 pages) ,
- Instruction manual (24 pages) ,
- Instructions manual (12 pages)
Table of Contents
Advertisement
Quick Links
DS160 Strobe
Product Numbers 4060US • 4060EU • 4060AU • 4060UK
DS161 Strobe
Product Numbers 4061US • 4061EU • 4061AU • 4061UK
Product Registration
Please register your product at www.ikelite.com within 15 days of
purchase. Our product registration database is the best way for us to
get a hold of you in the event of a product update or recall.
Advertisement
Table of Contents
Related Manuals for Ikelite DS160
Summary of Contents for Ikelite DS160
-
Page 1: Product Registration
Product Numbers 4061US • 4061EU • 4061AU • 4061UK Product Registration Please register your product at www.ikelite.com within 15 days of purchase. Our product registration database is the best way for us to get a hold of you in the event of a product update or recall. -
Page 2: About This Product
Included in the Box • DS160 Strobe Front # 4060.2 or DS161 Strobe Front # 4061.2 • Rechargeable NiMH Battery Pack # 4066.5 • Battery Pack Cover # 0591.4 •... -
Page 3: Important Notices
Important Notices » The battery pack is NOT waterproof when removed from the strobe front. » NEVER use, ship, or travel with a water damaged battery pack. Use of a water damaged battery pack is a safety risk and can cause damage to the strobe electronics. -
Page 4: Table Of Contents
Contents Product Registration About this Product Included in the Box Important Notices Getting to Know Your Strobe Setting Up Your Strobe Removing the Battery Pack Attaching the Battery Pack Using the Diffuser Attaching the Diffuser Choosing an Arm System Attaching a Sync Connector Using Your Strobe Checking Battery Level Turning the Strobe On... -
Page 6: Getting To Know Your Strobe
Getting to Know Your Strobe Shroud Flashtube Battery Pack Refl ector DS161 Video Light DS160 Modeling Light Mount Bulkhead... - Page 7 Toggle Lock BACK Mount Power Exposure Switch Switch Fuel Switch Fuel Gauge Lock TTL Full Gauge Batt w/Lite Ready Light w/Lite SIDE...
-
Page 8: Setting Up Your Strobe
Setting Up Your Strobe Removing the Battery Pack » The battery pack is NOT waterproof when detached from the strobe front. 1. Turn the Power Switch to the OFF position and place the strobe face down on a fl at surface. 2. -
Page 9: Using The Diffuser
3. Place the toggle lock in the open position by sliding out, fl ipping up, and rotating 90 degrees counter-clockwise. 4. Align the battery pack with the front of the strobe. The switches on the side of the strobe and battery pack will line up when properly oriented. -
Page 10: Choosing An Arm System
• Although not necessary, you may apply a small amount of Ikelite silicone lubricant to the screw prior to attaching the strobe mount to avoid seizing up with long term use. DO NOT apply Loc-tite or any other thread locking product as this may cause damage to the strobe’s plastic components. -
Page 11: Attaching A Sync Connector
1. Remove the bulkhead cap. 2. Lightly lubricate the connector o-ring. We recommend using only Ikelite silicone lubricant to eliminate the possibility of swelling due to incompatible compounds. 3. Line up the pins and receptacles and insert the sync cord plug into the bulkhead. -
Page 12: Using Your Strobe
Using Your Strobe Checking Battery Level When the switch is rotated to the Batt w/Lite position, the Fuel Gauge will indicate approximate remaining battery level. Each LED represents approximately 25% of the battery capacity. Fuel Gauge 75-100% 50-75% 25-50% 0-25% The Fuel Gauge does not indicate remaining battery life when the strobe is in the Off, On, or On w/Lite positions. -
Page 13: Using The Exposure Control
In this position the LEDs marked 1 / 2 / 3 indicate the approximate remaining battery level. The fl ash does not fi re in this mode. The video (DS161) or modeling light (DS160) stays on. The exposure switch will increase or reduce the intensity of the video light (DS161 only). -
Page 14: Positioning The Strobe
• In ON or ON W/LITE power setting, the strobe will automatically adjust the fl ash duration based on signals received from the camera or trigger device. Use only with compatible systems and accessories; refer to your housing instruction manuals for information on TTL compatibility with this strobe. -
Page 15: Maintenance
• The Ready Light LED on the side of the strobe will glow red when the strobe is ready to fi re. • The Ready Light LED doubles as a confi dence signal. The LED will momentarily glow green after the strobe fi res if the strobe has received a TTL quench signal. -
Page 16: Troubleshooting
2. Lightly lubricate the threads of the bulkhead. Be careful not to get lubricant inside the gold connectors or rubber grommet inside of the bulkhead. 3. Attach the waterproof bulkhead cap to the bulkhead. 4. Rinse the strobe with fresh water and dry thoroughly. 5. - Page 17 • Adjust aperture (larger), shutter speed (slower), or ISO (lower) setting. • Move strobe(s) closer to your subject and check aiming. Strobe will not fi re when using sync cord. • Make sure the strobe is turned on. • Try a different sync cord. •...
-
Page 18: Photo Tips
Photo Tips 1. Be mindful of your depth, decompression limits, air supply, the location of your dive buddy, and the proximity of other divers at all times. No photo is worth risking your safety or the safety of others. 2. Move in close to your subject to photograph through as little water as possible. -
Page 19: Limited Warranty
Limited Warranty The DS160 or DS161 strobe front is warranted against any original manufacturing defects for a period of two (2) years from the original date of purchase. All other components including the battery pack and smart charger are warranted against any original manufacturing defects for a period of one (1) year from the original date of purchase. -
Page 21: Contact Us
If you have any questions about your product or need advice on getting the images you want, please get in touch with us and we’ll do everything we can to help you capture your unique perspective. Ikelite Underwater Systems 50 W 33rd St Indianapolis, IN 46208 USA (317) 923-4523 ikelite@ikelite.com...