Page 1
I n s t r u c t i o n M a n u a l 6116.12 Sony RX100 III (DSC-RX100M3/B) Thank you for your purchase of Ikelite equipment. Please read this instruction manual completely before attempting to operate or dive with this product.
Table of Contents Preparation ..............P. 3 Specifications ..............P. 4 What’s in the Box ............P. 4 Parts of the Housing - Front View ........P. 5 Parts of the Housing - Back View ........P. 6 Housing and Camera Setup ........P. 7 STEP 1 - Initial Camera Setup ........P. 7, 8 STEP 2 - Opening the Housing ........P.
Table of Contents continued Maintenance ..............P. 21 - 24 Photo Tips ..............P. 25 Troubleshooting ............P. 26 - 28 Spare Parts ..............P. 29 Customer Support ............P. 30 Limited Warranty ............P. 30 Returning Products for Service ........P. 31 Product Registration ..........Back Page Preparation This product has been water pressure tested at the factory and is depth rated to 200 ft (60 m).
Specifications (no camera installed) Depth Rating......200 ft (60 m) Controls ........All important camera functions accessed ..........except Flash switch and Viewfinder switch Buoyancy ......Slight negative buoyancy in fresh water Housing Weight ....4.7 lb (2.1 kg) Strobe Connection ....Fiber Optic Ports Use Built-in Flash....Yes Optional Tray Mounting ..12-24 thread external tray mounting with 3 in ..........(76 mm) spacing Main O-Ring ......0109...
Parts of the Housing - Front View Housing controls are provided for all camera functions except the flash up switch and viewfinder switch. The built-in camera flash must be extended BEFORE placing the camera in the housing. Zoom Lever Shutter Mode Dial ON/OFF (Power) Button Release...
Parts of the Housing - Back View MENU Control Wheel Housing MOVIE Button Set / Tracking Focus 2. Fn Function Button Flash Mode / Right Button 3. MENU Button Exp. Comp. / Down Button DISP Display / UP Button Playback Button 5.
Housing and Camera Setup STEP 1 - Initial Camera Setup (before placing camera in housing) Setup your camera for underwater use and then adjust your settings once underwater. Set Mode Dial to “A” Aperture Priority. Manually adjust aperture setting to achieve the best exposure for your shooting conditions.
STEP 1 - Initial Camera Setup - continued If close-up images are overexposed, adjust aperture setting and/or use “-” Flash Exposure Compensation and/or back away, zoom in, and then reshoot. RAISE the camera flash before placing camera in housing (no housing control is provided for this function).
Page 9
STEP 3 - Attach Camera to Mounting Tray - continued Diagram B SONY ZEISS * Control Wheel “cut away.” When not Mounting Tray in use, rotate Control Wheel knob white dot to the 6 o’clock position so “cut away” is over camera dial and Mounting Tray Bolt not contacting camera.
STEP 4 - Attach the Control Ring Gear The supplied Control Ring Gear is attached to the camera control ring by 3 small nylon Allen Set Screws. Place the Control Ring Gear over the camera’s step ring before installing the camera in the housing. The Gear is a “press fit”...
STEP 5 - Installing Camera in the Housing 1. Pull out on each housing control until it stops. This will get the controls out of the way for installation of the camera. 2. Remove camera lanyard from camera if attached. 3.
STEP 7 - Final Check The clear housing permits instant visual inspection of the camera and sealing surfaces as well as complete monitoring of controls and camera LCD screens. This housing has been factory water pressure tested to 200 ft (60 m). Once the housing is closed, recheck the o-ring seal.
Using the Camera’s Built-in Flash If you are shooting with the camera’s built-in flash and the camera lens is set to the widest angle setting, you may need to zoom the lens slightly or a dark area may appear in a lower corner of close-up photographs. The lens port may block some of the light.
Diffuser Purpose When using the built-in camera flash and shooting close-up photographs, the lens port on the housing can block a portion of the light from the built-in camera flash. This can result in a shadow in a lower corner of the picture frame.
The color filters are for available light use only. Not recommended when using external strobes. Optional Tray with Release Handle 9523.61 The optional aluminum tray with release handle comes with the necessary hardware to mount to your Ikelite housing. To attach, see page 17.
Page 17
Attach Optional Tray + Dual Handles to Housing Attaching an optional Tray + Dual Handles will add stability and gripping point(s) for comfortable use of the housing. Add a second strobe to eliminate shadows and evenly light your subjects. Attach Optional Tray with Release Handle(s) to Housing 1.
Page 18
The AF35 Strobe Package is available to support your housing along with a full range of accessories. Please visit www.ikelite.com to see additional information regarding this and other strobe package options.
Page 19
We recommend the Ikelite W30 Wide Angle Lens or INON UWL-H100 Wide Angle Lens for excellent edge sharpness with minimal vignetting (dark shadows in the corners of the image). Vignetting may be eliminated by either zooming slightly or cropping the image in post-production.
Additional Accessories 2602.3 Quick Release Handle Kit for GoPro Gamma LED Focus/Flashlight A full range of accessories are available to support your housing. Please visit www.ikelite.com to see the most current information about recommended accessories for your housing.
Lubricant Ikelite provides silicone lubricant with the housing. We recommend you use only Ikelite lubricant on Ikelite products. Other brands may cause the main housing o-ring to swell and not seal properly. Use only enough lubricant to lightly cover the main housing o-ring or lubricate a sticky control.
Page 22
Housing Maintenance Your Ikelite Digital Housing should be given the same care and attention as your other photographic equipment. In addition to normal maintenance, we recommend that the housing be returned to Ikelite periodically to be checked and pressure tested.
After a few minutes, operate the push button. If this does not correct the problem, return the housing to Ikelite for maintenance. If you are on a trip and unable to return the housing immediately, a push button may be lubricated by pressing and holding the push button all the way in.
Page 24
In the unlikely event one of the larger gland style control shafts sticks or becomes difficult to operate, you can remove the control from the housing and lubricate it, or return the housing to Ikelite for maintenance. To remove the control, Diagram F, loosen the set screw in the knob (allen wrench required);...
Photo Tips The number one rule in underwater photography is to eliminate as much water between the camera and subject as possible. Get as close as you can to the subject, then use the zoom. If you are using flash for still photos, subjects beyond 6 ft (1.8 m) will not have much color regardless of strobe power.
If still sticky, see the Control Maintenance section, Diagram F, page 24. - Return housing to Ikelite for routine maintenance. Image is - Check that the built-in flash or external strobe is over/underexposed, firing when taking a picture.
Page 27
Place one or two new packs in your housing before each day of diving. - If moisture or water droplets are present around the controls or sealing areas, return the housing to Ikelite for evaluation. - Clean the main housing o-ring and sealing surface of the housing.
Page 28
- Look for hair, dirt, or foreign debris crossing the o-ring seal. - Reassemble the housing without a camera installed and immerse in water. - Return housing to Ikelite for evaluation. Pictures are too blue - Use custom (manual) white balance. Reset for or too green each working depth or when attaching a color correcting filter to the camera lens.
Spare Parts (available through Ikelite or any Ikelite Dealer) 0184.2 Silicone Lubricant 2cc Reclosable Tube 0119.2 Port o-ring 0200 Port cover 0109 Main o-ring 9523.10 Tray Hardware 0945.18 Allen Wrench for control knobs 0945.11 Allen Wrench for Control Ring small nylon set screws...
This Ikelite product is warranted against any manufacturing defects for a period of one (1) year from the original date of purchase. Defective products should be returned to Ikelite postage paid. Ikelite will, at its sole discretion, repair or replace such products, and will return to customer postage paid.
Returning Products For Service Ikelite is most interested in performing any service to ensure that all products perform as intended. Evidence of purchase date must be provided to obtain warranty service. No prior authorization is required. You may return directly to us or through your dealer.