Ikelite DS160 Instruction Manual
Strobe
Hide thumbs
Also See for DS160:
- Instructions manual (24 pages) ,
- Manual (21 pages) ,
- Instruction manual (5 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Ikelite DS160
Summary of Contents for Ikelite DS160
- Page 1 DS160 Strobe I n s t r u c t i o n M a n u a l Please read all instructions before using this product.
-
Page 2: Table Of Contents
Strobe Ready Light and TTL Housing..19 Strobe Compatibility ......4 Camera Ready Light ......19 Strobe Power ........4 Triggered via Sync Cord ......19 DS160 Strobe ........5 Overview of DS160 Features ....5 RECOMMENDATIONS......20 Visual Inspections ........20 OPENING AND CLOSING ....6 Insurance ..........20 Opening the Strobe......6 Tips ............20... -
Page 3: Ikelite Ds160 Strobe
IKELITE DS160 STROBE DS160 SPECIFICATIONS CE - Compliant with applicable EU directives Complies with FCC part 15, subpart B, Section 15.109 for Class “B” Products S p e c i f i c a t i o n s Battery Pack ..........Li-ion module, 7.4v, 4500mAh Weight ............2.5 lb (1130g) -
Page 4: Introduction
STROBE POWER The DS160 recycles in a quick 1.4 sec from full discharge. When fired at a fractional power — whether in TTL or manual mode — the strobe recycles virtually instantaneously. Number of flashes per full charge will increase dramatically in most cases when using in TTL mode with a compatible camera system. -
Page 5: Ds160 Strobe
100° using the diffuser. Special soft-lite reflector provides rich reds, oranges, and warmer flesh tones. The DS160 is pre-flash compatible and operates with both traditional film cameras and digital still cameras. Multiple firing modes are featured, including TTL/Auto exposure. -
Page 6: Opening And Closing
The Li-ion batteries remain permanently secured inside the Li-ion battery pack. The front section of the DS160, which houses the main electronics, is safely sealed separately from the battery pack. The front section will remain waterproof when the battery pack is removed. -
Page 7: Opening And Closing (Illustration)
OPENING AND CLOSING (illustration) Pull Out Flip Up Rotate... -
Page 8: Li-Ion Battery Pack 4067
LI-ION BATTERY PACK 4067 The 4060.1 DS160 Strobe includes a Lithium Ion (Li-ion) battery pack and smart charger. The battery pack requires Smart Charger 4067.1 (page 10). Li-ion Battery Pack 4067 is compatible with Ikelite's DS125, DS160 and DS161 Strobe. -
Page 9: Charging The Battery Pack
Do not ship or travel with a flooded or known defective battery pack. USING NIMH OR NI-CAD BATTERY PACKS The DS160 Strobe head also accepts both 4066.5 NiMH battery packs and 4066 Ni-Cad battery packs in good working condition. Do not use a battery pack with dead or water damaged cells. -
Page 10: Smart Charger 4067.1
European plug adapter Australian plug adapter United Kingdom plug adapter USAGE Use only with compatible Ikelite lithium-ion battery Adapter Prongs Closed Attached packs. Charge a battery pack to at least half full prior to storing for extended periods of time. This charger features flip out blades for use with US plugs. -
Page 11: Flash Diffuser 0591.3
FLASH DIFFUSER 0591.3 USING THE DIFFUSER The white diffuser can be secured to the front of the DS160 Strobe when softer lighting or a coverage angle of 100° is desired. The diffuser reduces the DS160’s light intensity by one full f-stop. -
Page 12: Arm Systems/Strobe Mounts
ARM SYSTEMS / STROBE MOUNTS IKELITE ARM SYSTEMS Ikelite offers several arm choices compatible with the DS160. The arm and strobe mount are NOT supplied with the strobe. For additional information go to www.ikelite.com Caution: Ikelite arm systems are designed for underwater use. Be careful when transporting the system above water since some camera trays and arm adjustments may be unable to support the weight of the strobe(s) above water. -
Page 13: Strobe Connection
(page 14). CONNECTION TO STROBE To connect either a sync cord or sensor to the DS160 Strobe, follow these instructions: Turn the strobe to OFF and make sure all components are dry. Clean and lightly lubricate the stem o-ring and the bulkhead connector threads. -
Page 14: Strobe Connection (Illustration)
STROBE CONNECTION (illustration) DS160 Strobe Bulkhead Connection Bulkhead Cap Stem O-ring Retaining Ring Blue Band 4103.51 Ikelite Sync Cord... -
Page 15: Using As Hard-Wired Strobe Without Ttl
- Non-Ikelite housings for digital cameras with Nikonos-style strobe connector Connect the strobe using an appropriate Ikelite sync cord. The DS160 must be used in manual exposure modes. Strobe output is not automatically adjusted for proper exposure when set to TTL(Auto) mode. -
Page 16: Aiming The Strobe
When using auto-focus cameras, the modeling light may be required in low light levels to illuminate your subject to allow the camera to auto focus. Always hold onto the center of the strobe when repositioning. Do not reposition the strobe by holding the back of the battery pack. DS160 Strobe Flash Tube Modeling Light... -
Page 17: Switches / Fuel Gauge
SWITCHES / FUEL GAUGE The DS160 features separate switches for power on/off and firing modes. The arrow on the switch points to the selected position. ON/OFF SWITCH OFF: The horizontal switch position is OFF. The adjacent tab locks the switch in the OFF position. -
Page 18: Fuel Gauge
No LED - less then 25% CONFIDENCE SIGNAL The DS160 strobe features a confidence signal indicator light that will glow if the strobe receives a TTL quench signal. The #3 LED on the fuel gauge will glow GREEN for three seconds if the DS160 strobe quenches. -
Page 19: Strobe Ready Light
The middle #2 LED on the fuel gauge functions as the visual ready light. The #3 LED on the fuel gauge will glow GREEN for three seconds if the DS160 strobe quenches, indicating that the strobe has provided proper exposure. If no green light appears, check the image for possible under-exposure. -
Page 20: Recommendations
Weak batteries are the cause of many strobe and camera problems. Do not fire the strobe more than 15 times above water in rapid succession. If this • does happen, allow the DS160 to cool off for at least 10 minutes before resuming photography. LUBRICANT Use only Ikelite brand silicone lubricant with Ikelite brand •... -
Page 21: Maintenance
MAI NTENAN C E Your Ikelite DS160 Strobe should be given the same care and attention as your other photographic equipment. After using your strobe in water, please follow these instructions to ensure the DS160’s longevity and good working order. -
Page 22: Troubleshooting
If the DS160 flashes, the source of the problem lies somewhere in the camera. If the DS160 does not flash, please send both the strobe and cord used in the test to an authorized Ikelite dealer, or to Ikelite; see “Technical Support” on page 23. -
Page 23: Airline Travel
The Ikelite DS160 Strobe Head is warranted against any manufacturing defects for a period of two (2) years from the original date of purchase. The DS160 Li-ion Battery Pack is warranted against any manufacturing defects for a period of one (1) year from the original date of purchase. -
Page 24: Product Registration
PRODUCT REGISTRATION Please visit www.ikelite.com to register your Ikelite Digital Strobe within 15 days of purchase. Ikelite Underwater Systems 50 West 33rd Street Indianapolis, IN 46208 USA www.ikelite.com © 2013 Ikelite Underwater Systems DS160 Strobe_4060.1-03-0714...