Download Print this page
ADTRAN Total Access 362R Manual
ADTRAN Total Access 362R Manual

ADTRAN Total Access 362R Manual

Single family unit with rf return
Hide thumbs Also See for Total Access 362R:

Advertisement

Quick Links

Product P/N: 1187715G1
Surface Mounting
Hole
POWER
Hinge
NETWORK STATUS
POTS 1
POTS 2
TOTAL ACCESS 362R
TELEPHONE TROUBLESHOOTING
1. Identify the bad line.
2. Disconnect the plug from the appropriate POTS jack and plug
any working telephone into that jack.
If the telephone works, there is a problem inside the house.
If the telephone does not work, contact your service provider.
3. Remove the telephone and replace the plug into the POTS jack.
Security
4. Close the unit.
TELCO ACCESS
Screw
12V
, 1.5A
Hinge
Fiber Optic
Surface
Cable
Mounting
Hole
Ground
RF Drop
Power
Fiber Drop
Ground Drop
D
ESCRIPTION
®
The Total Access
 362R Single Family Unit (SFU) Optical 
Network Terminations (ONT) is a Gigabit Passive Optical 
Network (GPON) ONT with RF Return. The Total Access 362R 
SFU ONT has two POTS, two Gigabit Ethernet and one RF Return 
interfaces. The figure above illustrates the 362R SFU inner 
enclosure.
GPON technology provides a consistent and common approach 
to advancing the public communications network using:
Traditional telephone service [Plain Old Telephone Service 
(POTS)]
High speed data services
RF Video services 
The network consists of an Optical Line Terminal (OLT) located at 
the central office and Optical Network Terminals (ONT) located 
at the customer premises. 
To allow for the transmission of downstream and upstream traffic 
on one single fiber, different wavelengths are used for each 
direction. Downstream traffic uses 1490 nm, while upstream 
traffic is carried on 1310 nm. For return of RF TV distribution, 
1550 nm is used for downstream RF TV and 1610 nm is used for 
the upstream RF return path.
Total Access 362R
Single Family Unit with RF Return
Two-screw
Terminal
Bridges
TIP
RING
TIP
RING
POTS 1
FXS 0/1
FXS 0/2
POTS 2
TIP
RING
ETH 0/1
ETH 0/2
Ethernet
ETH 0/1
ETH 0/2
ETH 1
ETH 2
Connections
1187715G1
TEL. NUMBER
CLEI
RF
Connection
Ethernet Drop
POTS Drop
Ground and Power
Drop Callout
This Job Aid covers the electronics modules (362R SFU) and 
housings listed in the following table:
Total Access 362R
Description
1187715G1
Total Access 362R SFU Electronics Module
1187770G1
Total Access Splice Housing
1187771G1
Total Access OptiTap Housing
NOTE
The Total Access 362R SFU ONT is only intended to be used with
the Adtran Network Interface Device (NID) housings listed
above.
F
P
LED
RONT
ANEL
Label
Status
POWER
Off
Green
NETWORK
Green
STATUS
Yellow
Red
POTS
Off
1 and 2
Green
2
Green Flashing
ETH 1 and 2
Off
Green
4
Yellow Flashing
I
NSTALLATION
After unpacking the 362R SFU, inspect it for damage. If damage is 
noted, file a claim with the carrier and then contact ADTRAN. For 
more information, refer to the warranty.
NOTE
Refer to the Total Access 362R Single Family Unit with RF Return
Installation and Maintenance Guide (P/N 64187715G1‐5) for
complete information on installing this unit.
Required Tools and Supplies
Standard technician tools and those listed below are required for 
installing the 362R SFU:
Carpenter's level
3/32" screw driver for connecting 362R SFU power
5/32" hex tamper proof bit
RJ‐11/RJ‐45 crimper
Issue Date: January 2011
Document P/N: 61187715G1-22B
S
Description
No power
Power is On
OLT has activated the ONT
OLT is discovering and ranging 
the ONT
The OLT has shut down ONT
Fiber is disconnected, or GPON 
interface is down
At least one port is Off Hook
At least one port is Ringing
Link is down: no activity or 
Administratively Shut Down
10/100/1000 Link is up
TX or RX activity
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the Total Access 362R and is the answer not in the manual?

Questions and answers

Summary of Contents for ADTRAN Total Access 362R

  • Page 1 Total Access 362R Single Family Unit with RF Return Issue Date: January 2011 Product P/N: 1187715G1 Document P/N: 61187715G1-22B This Job Aid covers the electronics modules (362R SFU) and  Surface Mounting Two-screw Hole housings listed in the following table: Terminal Bridges Total Access 362R Description RING POWER RING POTS 1 FXS 0/1 Hinge NETWORK STATUS 1187715G1 Total Access 362R SFU Electronics Module...
  • Page 2 ♦ A telephony/data communication test set customer premises. Ensure the wire is free of any sharp  ♦ bends. PON power meter with wavelength filtering ♦ 5. Attach the ground wire to the side of the customer premises  Fiberscope or videoscope with stainless steel half moon clamps or tie‐wrap the ground  ♦ Two #10 screws and appropriate surface anchors for mounting  wire to the riser conduit of the Buried Fiber Drop.  the 362R SFU 6. Clean the MGN connector with emery cloth to insure a  ♦ Assorted tie wraps for securing cabling and wiring stable connection. ♦ Two RJ‐45 plugs 7. Attach the ground wire from the 362R SFU to the MGN  ♦ Two RJ‐11 plugs (when not using two‐screw terminal bridges) connector with the appropriate UL approved ground clamp/ For fiber optic connections, the following are required: fitting. ♦ Fiber splicing tools 8. Coat the connection with a metal corrosion preventative. ♦ Fiber cleaning materials 9. Attach a Warning Ground Tag to this grounding connection. Included with the 362R SFU packaging are 2 two‐screw terminal  bridges, fiber cable management and strain relief, a fiber  connector, and electronics/optics. For data, the connection to the  SFU is through the R‐J45 Ethernet connectors. For POTS, the ...
  • Page 3 6. Tie Wrap the wires using the appropriate tie wrap anchor  This 362R SFU should only be operated from the type of certified/ points. listed power supply recommended by the power supply  manufacturer. 7. Replace the rubber grommet while closing the Electronics  Module. This places less stress on the wiring and allows the  Electronics Module to close without pinching any wiring.  Pin 1 Low Battery Route OptiTap Fiber Drop Cable Battery Missing Pin 7 Replace Battery Refer to the illustration below for fiber installations. On Battery 1. Place the OptiTap fiber drop in the same rubber grommet  Signal Return 12V Return channel as the ground cable. The ground cable should be  +12VDC “below” the OptiTap fiber.  Power/Alarm UPS Power 2.
  • Page 4 From within the U.S. 1.800.726.8663 From outside the U.S. +1 256.963.8716 Warranty: ADTRAN will replace or repair this product within the warranty period if it does not PRICING AND AVAILABILITY 1.800.827.0807 meet its published specifications or fails while in service. Warranty information can...

This manual is also suitable for:

1187715g1