PowerTec HS1002 Owner's Manual page 3

WARNING
For your own safety, read and understand all warnings
and operating instructions before using any tool or
equipment.
WARNING
Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contain chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other
masonry products.
• Arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures vary, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area and work
with approved safety equipment. Always wear OSHA/
NIOSH approved, properly fitting face mask or respirator
when using such tools.
WARNING
Failure to follow these rules may result in serious personal
injury. Remember that being careless for even a fraction
of a second can result in severe personal injury.
WORK PREPARATION
• Wear proper apparel. Do not wear loose clothing,
gloves, neckties, rings, bracelets or other jewelry which
may get caught in moving parts of the tool.
• Nonslip protective footwear is recommended. Wear
protective hair covering to contain long hair.
• Wear eye and hearing protection. Always use safety
glasses. Eye protection equipment should comply with
ANSI Z87.1 standards. Hearing equipment should
comply with ANSI S3.19 standards.
• Wear face mask or dust mask if operation is dusty.
• Be alert and think clearly. Never operate power tools
when tired, intoxicated or when taking medications that
cause drowsiness.
WORK AREA PREPARATION
• Keep work area clean. Cluttered work areas and
benches invite accidents.
• Work area should be properly lit.
• Do not use the machine in a dangerous environment.
The use of power tools in damp or wet locations or in
rain can cause shock or electrocution.
• Do not use the machine in the presence of flammable
liquids or gases.
• The tools plug must match the outlet. Never modify
the plug.
• Do not abuse the power cord. Do not use the cord to
carry the tool. Do not pull on the cord to unplug the tool.
Keep the power cord away from heat, sharp edges or
moving parts. Damage to the cord increases the risk of
electrical shock.
GENERAL SAFETY RULES
• Avoid body contact with grounded surfaces. There
• Use the proper extension cord. Make sure your
• Keep children and visitors away. Your shop is a
• Make your workshop childproof with padlocks, master
TOOL MAINTENANCE
• Turn the machine "OFF", and disconnect the machine
• Maintain all tools and machines in peak condition. Keep
• Follow instructions for lubricating and changing
• Check for damaged parts. Check for alignment of
• Poorly maintained tools and machines can further
• A guard or any other part that is damaged should be
• Inspect power cords often. If power cord is damaged,
TOOL OPERATION
• Avoid accidental start-up. Make sure that the tool is in
• Use the right tool for your job. Do not force your tool or
• Disconnect tool when changing parts.
• Don't force the workpiece on the machine. Damage to
• Never leave tool running unattended. Turn the power off
• Do not overreach. Loss of balance can make you fall
• Never stand on tool. Injury could occur if the tool tips, or
• Know your tool. Learn the tool's operation, application
• Use a proper extension cord of the correct gauge. Your
• Handle workpiece correctly. Keep hands away from
Think safety! Safety is a combination of operator common
sense and alertness at all times when tool is being used.
Do not attempt to operate tool until it is completely
assembled according to the instructions.
is an increased risk of electrical shock if the body is
grounded.
extension cord is in good condition.
potentially dangerous environment. Children and visitors
can be injured.
switches or remove switch keys to prevent any
unintentional use of power tools.
from the power source prior to inspection.
tools sharp and clean for best and safest performance.
accessories.
moving parts, binding, breakage, mounting and any
other condition that may affect tool's operation.
damage the tool or machine and/or cause injury.
repaired or replaced. Do not perform makeshift repairs.
have it replaced immediately by an authorized service
center.
the "OFF" position before plugging in.
attachment to do a job for which it was not designed.
the machine and/or injury may result.
and do not leave tool until it comes to a complete stop.
into a working machine, causing injury.
if you accidentally contact the cutting tool.
and specific limitations before using it.
extension cord should be in good condition.
moving parts.
CAUTION
WARNING
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
1
1