Campbell Hausfeld WG2060 Operating Instructions And Parts Manual page 2

Wire Feed Arc Welder
supported and grounded prior to
General Safety
beginning any electric arc welding
(Continued)
operation.
NOTE: Note means any additional
G Spread out coiled welding cable
information pertaining to the product
before use to avoid overheating and
or its proper usage.
damage to insulation.
WARNING
! DANGER
!
Always keep a fire
gun in water. If welder becomes wet for
extinguisher accessible
any reason, be absolutely certain it is
while performing arc
completely clean and dry before use!
welding operations.
G Always shut equipment off and
G Before starting or
unplug power cord prior to moving
servicing any electric arc welder, read the unit.
and understand all G Always attach the work lead first.
instructions. Failure
G Verify work piece is securely
to follow safety
grounded.
MANUAL
precautions or
G Always shut off electric arc welding
instructions can
equipment when not in use and cut off
cause equipment
any excess wire from wire feed gun.
damage and/or serious personal
G Never allow any part of the body to
injury or death.
touch flux-cored wire and ground or
G All installation, maintenance, repair
grounded work piece at the same
and operation of this equipment
time.
should be performed by qualified
G Awkward welding conditions and
persons only in accordance with
national, state, and local codes. positions can be electrically hazardous.
When crouching, kneeling or at
WARNING
!
elevations, be sure to insulate all
Improper use of electric
conductive parts, wear appropriate
arc welders can cause
protective clothing and take
electric shock, injury,
precautions to prevent injury from falls.
and death! Take all
G Never attempt to use this equipment
precautions described in
this manual to reduce the possibility of
at current settings or duty cycles higher
electric shock.
than specified on equipment labels.
G Verify all components of the arc
G Never use an electric arc welder to
welder are clean and in good
thaw frozen pipes.
condition prior to operating welder.
Be sure insulation on all cables, wire
WARNING
!
feed gun and power cord is not
Flying sparks and hot
damaged. Always repair or replace
metal can cause injury.
damaged components before
As welds cool, slag can
operating the welder. Always keep
be thrown off. Take all
welder panels, shields, etc. in place
precautions described in
when operating welder. this manual to reduce
the possibility of injury from flying
G Always wear dry, protective
sparks and hot metal.
clothing, welding gloves and
G Wear ANSI approved face shield or
insulated footwear when operating
safety glasses with side shield
unit.
protection when chipping or
G Always operate welder in a clean,
grinding metal parts.
dry, well ventilated area. Do not
G Wear ear plugs when welding
operate welder in humid, wet, rainy
overhead to prevent spatter or slag
or poorly ventilated areas.
from falling into ears.
G Be sure work piece is properly
www.chpower.com
WARNING
!
Electric arc welding
operations produce
intense light and heat
and ultraviolet (UV)
rays. This intense light
and UV rays can cause injury to eyes and
Never immerse
skin. Take all precautions described in
wire or wire feed
this manual to reduce the possibility of
injury to eyes and skin.
G All persons operating this equipment
or in the area while equipment is in
use, must wear protective welding gear
including: welding helmet or shield
with at least shade 10 lens, flame
resistant clothing, leather welding
gloves and full foot protection.
Never look at arc
WARNING
!
welding operations
without eye protection as described
above. Never use a shade filter lens
that is cracked, broken, or rated below
number 10. Warn others in the area not
to look at the arc.
WARNING
!
Electric arc welding
operations cause sparks
and heat metal to
temperatures that can
cause severe burns! Use
protective gloves and clothing when
performing any metal working
operation. Take all precautions described
in this manual to reduce the possibility
of skin and clothing burns.
G Make sure all persons in welding
area are protected from heat, sparks
and ultraviolet rays. Use additional
face shields and flame resistant
barriers as needed.
G Never touch work pieces until
completely cooled.
WARNING
!
Heat and sparks
produced during
electric arc welding and
other metal working
operations can ignite
flammable and explosive materials!
Take all precautions described in this
manual to reduce the possibility of
flames and explosions.
G Remove all flammable materials
within 35 feet (10.7 meters) of
welding arc. If removal is not
possible, tightly cover flammable
materials with fire proof covers.
2
Notes
Notes
Notas
Models WG2060 and WG2064
Modèles WG2060 et WG2064
Modelos WG2060 y WG2064
43