Sony BVP-500 Maintenance Manual page 51

Page Ver. Item
FILTER,WHT MEM [ON], OFF
OTHERS 1
NTSC ENC
ROTARY
OWN CALL
CENTER H POS –20 to 20 ([XX])
CENTER V POS –20 to 20 ([XX])
LENS VTR S/S
VF ? DISPLAY
PinP RET RVS
OTHERS 2 F TALLY RVS
1.07 BLK GAM
INHIBIT
1.10 CHAR CAM No. 1,2,3 , A,B,C
1.10 WHT SETUP
MODE
1.10 AW SHADING
MODE
BVP-500
BVP-500P
Settings Contents
Does not function in the unit. (The setting change becomes invalid.)
[WIDE], NRW
Sets the band width of the Q signal for the NTSC color encoder.
[STD], RVS
Selects the mode of MENU SELECT knob as turned clockwise.
STD : Cursor moves downwards and a numeric value increases.
RVS : Cursor moves upwards and a numeric value decreases.
R, F&R , OFF Selects whether TALLY lamps are lit corresponding to the
CALL button on rear panel pressed, or not. Or selects which TALLY
lamps are lit when the CALL button is pressed.
(This setting is valid in connection with CCU. When the standalone unit is
installed and MSU/RCP is not connected to the camera, it is always set to OFF.)
R : Red TALLY lamps of VF are lit.
R&F : Red TALLY lamps of VF and UP TALLY lamps of VF and camera are lit.
OFF : No TALLY lamp is lit corresponding to the CALL button.
Shifts horizontally the location of the center marker on the screen.
20 (right) ↔ –20 (left)
Shifts vertically the location of the center marker on the screen.
20 (up) ↔ –20 (down)
TALK, [RET2]
Selects the mode of VTR S/S SW of the lens.
TALK : VTR S/S SW functions as INCOM TALK SW (momentary).
RET2 : VTR S/S SW functions as RET2 SW.
[ON], OFF
Turns on and off the indication of ? mark at the top-right of the VF screen with the
DISP switch set to ON when the self-diagnosis result is NG (no good) and so on.
[RVS1], RVS 2, OFF
Selects the indication mode of VF display in PinP mode.
Setting RET 1
RVS 1
RVS 2
OFF
* To output RET 3 video signal, press RET 1 and 2 switches at the same time.
[ON], OFF
Selects the operation mode of TALLY lamps corresponding to a CALL button
pressed when a TALLY signal is input to the camera from CCU or VTR.
ON : Red TALLY lamps of VF and UP TALLY lamps of VF and camera go out.
OFF : Red TALLY lamps of VF alone go out.
[ON], OFF
ON : Inhibits the black gamma adjustment and on/off function from the
OFF: Enables the above operation.
Selects the indication mode of the camera number set by the CAMERA
No. page of Operation menu.
1,2,3 : Indicates in numerics.
A,B,C : Indicates camera numbers 1 to 27 in alphabetical order of A to Z.
(When connecting 28 or more cameras, select "1,2,3".)
[AWB], LEVEL
AWB : After executing the LEVEL AUTO, white balance adjustment
LEVEL : After executing the LEVEL AUTO, white balance adjustment
[RGB], RB ONLY
RGB
RB ONLY : When automatically adjusting the white balance, R and B
Large screen
(or 2, 3) SW
ON RET 1 (2, 3) video
OFF Camera output
ON RET 1 (2, 3) video
OFF Camera output is displayed on the whole screen.
(Small screen is not displayed.)
ON Camera output
OFF Camera output is displayed on the whole screen.
(Small screen is not displayed.)
MSU or Paint manu.
data returns to the value before execution.
data changes to the value after the white balance is adjusted
using TEST 2 signal.
: When automatically adjusting the white balance, R, G, and
B signal waveforms are all flattened.
signal waveforms are flattened.
3-1. Setup Menu
3-1-6. System Config Menu
Small screen
Camera output
The last RET video selected
Camera output
RET 1 (2, 3) video
3-17