Related Manuals for Motomaster ELIMINATOR WORKSHOP 011-1980-4
Summary of Contents for Motomaster ELIMINATOR WORKSHOP 011-1980-4
- Page 1 ® model no. 011-1980-4 WORKSHOP SERIES Battery Charger IMPORTANT: INSTRUCTION Please read this manual carefully before running this battery MANUAL charger and save it for reference. 0099002120-00...
- Page 2 011-1980-4 | contact us 1-888-942-6686 This MotoMaster Eliminator product carries a three (3) year warranty against defects in workmanship and materials. At its discretion, MotoMaster Canada agrees to have any defective part(s) repaired or replaced free of charge, within the stated warranty period, when returned by the original purchaser with proof of purchase.
-
Page 3: Table Of Contents
® TABLE OF CONTENTS Safety Connecting Your Battery Know Your Charger Operation Charging Your Battery Battery Charging Times Automatic Voltage Detection Aborted Charge Desulfation Mode Completion of Charge Maintain Mode (Float Mode Monitoring) Maintaining a Battery Using the Engine Start Feature Using the Battery Voltage Tester Tester and Charger Testing After Charging... -
Page 4: Safety
011-1980-4 | contact us 1-888-942-6686 INTRODUCTION • To reduce risk of electrical shock, unplug the charger from the outlet before attempting This rugged MotoMaster Eliminator battery ® ® any maintenance or cleaning. charger features advanced microprocessor •... - Page 5 ® USING AN EXTENSION CORD • NEVER smoke or allow an open spark or flame in the vicinity of the battery or engine. The use of an extension cord is NOT Batteries generate explosive gases. recommended. If an extension cord must be used, •...
- Page 6 headline bars headline bars model no. 011-1980-4 | contact us 1-888-942-6686 PREPARING TO CHARGE CHARGER LOCATION DO NOT expose charger to rain or snow. Be sure that the area around the battery is • • continuation tabs continuation tabs well ventilated while being charged. Locate the charger as far away from the •...
-
Page 7: Connecting Your Battery
® BATTERY IN VEHICLE BATTERY IN VEHICLE (NEGATIVE GROUNDED) (POSITIVE GROUNDED) Before connecting and disconnecting the DC Before connecting and disconnecting the DC output clamps, remove the AC plug from the output clamps, remove the AC plug from the electrical outlet. electrical outlet. - Page 8 headline bars headline bars model no. 011-1980-4 | contact us 1-888-942-6686 BATTERY REMOVED FROM VEHICLE Position yourself and the free end of cable Before connecting and disconnecting the DC output clamps, remove the AC plug from the as far away from battery as possible, then continuation tabs continuation tabs connect the negative (black) charger clip to...
-
Page 9: Know Your Charger
® START/STOP BUTTON RATE SELECTION BUTTON Press to immediately begin charging your properly Use this button to select one of the following: connected battery. If the button is not pressed, • 6 A Charge – For charging small and large charging should begin automatically in 30 seconds. - Page 10 headline bars model no. 011-1980-4 | contact us 1-888-942-6686 BATTERY TYPE BUTTON This selects the type of battery to charge. • Normal (Standard) – Type of battery used • Gel – The electrolyte in a GEL cell has a continuation tabs in cars, trucks and motorcycles;...
-
Page 11: Operation
® CHARGING YOUR BATTERY BATTERY CHARGING TIMES Ah – Amp Hour Follow the instructions in the Connecting CCA – Cold Cranking Amps Your Battery section to connect your battery, RC – Reserve Capacity and then connect the charger to a live AC NR –... -
Page 12: Aborted Charge
headline bars model no. 011-1980-4 | contact us 1-888-942-6686 ABORTED CHARGE COMPLETION OF CHARGE If charging cannot be completed normally, Charge completion is indicated by the Charged/ charging will abort. When charging aborts, the Maintaining (green) LED. When lit, the charger has charger’s output is shut off and the Red LED will switched to the maintain mode of operation. -
Page 13: Using The Engine Start Feature
® USING THE ENGINE START FEATURE ENGINE STARTING NOTES During the starting sequence listed above, the Your battery charger can be used to jump start charger is set to one of four states: your car if the battery is low. Follow all safety •... -
Page 14: Using The Battery Voltage Tester
headline bars headline bars model no. 011-1980-4 | contact us 1-888-942-6686 USING THE BATTERY VOLTAGE TESTER POWER-UP AUTO START The charger is equipped with an auto-start With the charger unplugged from the AC outlet, feature which is triggered only when the charger connect the charger to the battery, following the is first powered up. -
Page 15: Maintenance
® MAINTENANCE A minimal amount of care can keep your battery charger working properly for years. • Coil the input and output cords neatly when • Clean the clamps each time you are finished charging. Wipe off any battery fluid that may storing the charger. -
Page 16: Troubleshooting
headline bars model no. 011-1980-4 | contact us 1-888-942-6686 PROBLEM POSSIBLE CAUSE SOLUTION The charger will not • AC outlet is dead. • Check for open fuse or circuit turn on when properly breaker supplying AC outlet. connected. • Poor electrical connection. •... -
Page 17: Error Codes
® CODE DESCRIPTION REASON/SOLUTION The battery voltage is still under 10 V (for a The battery could be bad. Have it checked or 12 V battery) or 5 V (for a 6 V battery) after replaced. 2 hours of charging. The battery could not be desulfated;... -
Page 18: Technical Specifications
Input current 6 A cont., 45 A int. Output voltage 6 V or 12 V Output current 6 V/12 V DC 6 A/15 A cont., 40 A/125 A int. notes warnings Made in Mexico Motomaster Canada Toronto, Canada M4S 2B8...