Related Manuals for WAGO 750-427/040-000
Summary of Contents for WAGO 750-427/040-000
- Page 1 Manual WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR 2-Channel Digital Input; 110 V DC; 3 ms; Extreme Version 1.2.1...
- Page 2 We wish to point out that the software and hardware terms as well as the trademarks of companies used and/or mentioned in the present manual are generally protected by trademark or patent. WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH. Manual Version 1.2.1...
-
Page 3: Table Of Contents
WAGO-I/O-SYSTEM 750 XTR Table of Contents 750-427/040-000 2DI 110V DC 3ms XTR Table of Contents Notes about this Documentation .............. 5 Validity of this Documentation ..............5 Copyright....................5 Symbols ....................6 Number Notation ..................8 Font Conventions ..................8 Important Notes .................. - Page 4 Table of Contents WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR 6.2.2 2 Channels, Low-side Switching ............38 6.2.3 1 Channel High-side Switching, 1 Channel Low-side Switching ..39 Use in Hazardous Environments ............40 Marking Configuration Examples ............41 7.1.1...
-
Page 5: Notes About This Documentation
(2DI 110V DC 3ms XTR). The I/O module 750-427/040-000 shall only be installed and operated according to the instructions in this manual, in the system description for the WAGO I/O SYSTEM 750 XTR and in the manual for the used fieldbus coupler/controller. -
Page 6: Symbols
Notes about this Documentation WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Symbols Personal Injury! Indicates a high-risk, imminently hazardous situation which, if not avoided, will result in death or serious injury. Personal Injury Caused by Electric Current! Indicates a high-risk, imminently hazardous situation which, if not avoided, will result in death or serious injury. - Page 7 WAGO-I/O-SYSTEM 750 XTR Notes about this Documentation 750-427/040-000 2DI 110V DC 3ms XTR Additional Information: Refers to additional information which is not an integral part of this documentation (e.g., the Internet). Manual Version 1.2.1...
-
Page 8: Number Notation
Notes about this Documentation WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Number Notation Table 1: Number Notation Number Code Example Note Decimal Normal notation Hexadecimal 0x64 C notation Binary '100' In quotation marks, nibble separated '0110.0100' with dots (.) -
Page 9: Important Notes
2.1.1 Subject to Changes WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from the granting of patents or from the legal protection of utility patents. -
Page 10: Technical Condition Of Specified Devices
These modules contain no parts that can be serviced or repaired by the user. The following actions will result in the exclusion of liability on the part of WAGO Kontakttechnik GmbH & Co. KG: •... -
Page 11: 2.1.4.1.2 Packaging
WAGO-I/O-SYSTEM 750 XTR Important Notes 750-427/040-000 2DI 110V DC 3ms XTR • Observe national and local regulations for the disposal of electrical and electronic equipment. • Clear any data stored on the electrical and electronic equipment. • Remove any added battery or memory card in the electrical and electronic equipment. -
Page 12: Safety Advice (Precautions)
Important Notes WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Safety Advice (Precautions) For installing and operating purposes of the relevant device to your system the following safety precautions shall be observed: Do not work on devices while energized! All power sources to the device shall be switched off prior to performing any installation, repair or maintenance work. - Page 13 WAGO-I/O-SYSTEM 750 XTR Important Notes 750-427/040-000 2DI 110V DC 3ms XTR Only connect or disconnect lines when power is safely isolated! The lines to the device can carry hazardous voltages and currents. Contact with the lines when live can result in severe injury or death. Therefore, read and observe the following safety rules before you perform work on the device: Disconnect the respective system component from the power supply.
- Page 14 Important Notes WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Do not use any contact spray! Do not use any contact spray. The spray may impair contact area functionality in connection with contamination. Do not reverse the polarity of connection lines! Avoid reverse polarity of data and power supply lines, as this may damage the devices involved.
-
Page 15: Device Description
The meaning of the LEDs is described in the “Display Elements” section. Only connect to I/O modules with the same field power supply! The I/O module 750-427/040-000 requires a field supply not equal to 24 VDC. Therefore, this I/O module 750-427/040-000 shall only be connected to modules having the same field power supply. - Page 16 Use a 750-612/040-000 power supply! For 110 VDC power on the field level, an additional 750-612/040-000 supply module must be positioned before a terminal block 750-427/040-000 or before I/O modules 750-427/040-000 arranged in blocks! The I/O module receives the 110 V voltage supply for the field level from an upstream I/O module via the power contacts used as blade contacts.
-
Page 17: View
WAGO-I/O-SYSTEM 750 XTR Device Description 750-427/040-000 2DI 110V DC 3ms XTR View Figure 1: View Table 3: Legend for Figure “View” Pos. Description Details See Section Marking possibility with Mini- Status LEDs “Device Description” > “Display Elements” Data contacts “Device Description” > “Connectors”... -
Page 18: Connectors
Device Description WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Connectors 3.2.1 Data Contacts/Local Bus Communication between the fieldbus coupler/controller and the I/O modules as well as the system supply of the I/O modules is carried out via the local bus. The contacting for the local bus consists of 6 data contacts, which are available as self-cleaning gold spring contacts. -
Page 19: Power Jumper Contacts/Field Supply
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent injury. Do not touch the blade contacts. The I/O module 750-427/040-000 has 2 self-cleaning power jumper contacts that supply and transmit power for the field side. The contacts on the left side of the I/O module are designed as blade contacts and those on the right side as spring contacts. -
Page 20: Cage Clamp ® Connectors
Device Description WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR ® 3.2.3 CAGE CLAMP Connectors ® Figure 4: CAGE CLAMP Connectors ® Table 5: Legend for Figure “CAGE CLAMP Connectors” Channel Designation Connector Function DI 1+ Input DI 1: Signal voltage (potential +) DI 1−... -
Page 21: Display Elements
WAGO-I/O-SYSTEM 750 XTR Device Description 750-427/040-000 2DI 110V DC 3ms XTR Display Elements Figure 5: Display Elements Table 6: Legend for Figure “Display Elements” Channel Description State Function Input DI 1: Signal voltage “0” Status DI 1 Green Input DI 1: Signal voltage “1“... -
Page 22: Schematic Diagram
Device Description WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Schematic Diagram Figure 6: Schematic Diagram Manual Version 1.2.1... -
Page 23: Technical Data
WAGO-I/O-SYSTEM 750 XTR Device Description 750-427/040-000 2DI 110V DC 3ms XTR Technical Data 3.5.1 Device Data Table 7: Technical Data – Device Width 12 mm Height (from upper edge of DIN-rail) 60.6 mm Depth 100 mm Weight 48 g Degree of protection IP20 3.5.2... -
Page 24: Mechanical Conditions
Device Description WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Table 11: Technical Data – Field Wiring ® Wire connection CAGE CLAMP Cross section 0.25 mm² … 2.5 mm² / AWG 24 … 14 Stripped lengths 8 mm … 9 mm / 0.33 in Table 12: Technical Data –... -
Page 25: Approvals
Approvals More information about approvals. Detailed references to the approvals are listed in the document “Overview Approvals WAGO I/O SYSTEM 750”, which you can find via the internet under: www.wago.com DOWNLOADS Documentation System Description. The following approval has been granted to 750-427/040-000 I/O modules:... - Page 26 Device Description WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR The following ship approvals have been granted to 750-427/040-000 I/O modules: ABS (American Bureau of Shipping) Temperature: D (cold test with −40 °C/16 h) Humidity: Vibration: B (vibration test with acceleration amplitude 5.0g)
-
Page 27: Standards And Guidelines
WAGO-I/O-SYSTEM 750 XTR Device Description 750-427/040-000 2DI 110V DC 3ms XTR Standards and Guidelines 750-427/040-000 I/O modules meet the following standards and guidelines: Table 16: Standards and Rated Conditions for Explosion Protection Applications ATEX acc. Directive 2014/34/EU General Requirements EN 60079-0:2012 + A11:2013... -
Page 28: Table 17: Climatic And Mechanical Environmental Conditions And Shipbuilding
Device Description WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Table 17: Climatic and Mechanical Environmental Conditions and Shipbuilding Standard Test Value Transport EN 60870-2-2 Ct2(2k4) (except precipitation/water/moisture) Mechanical Environmental Conditions EN 61850-3 Achieved EN 60870-2-2 EN 60721-3-1 EN 60721-3-3... -
Page 29: Table 18: Emc - Immunity To Interference
WAGO-I/O-SYSTEM 750 XTR Device Description 750-427/040-000 2DI 110V DC 3ms XTR The I/O module 750-427/040-000 meets the following EMC standards as these standards relate to the I/O module: Table 18: EMC – Immunity to Interference Standard Test Value Electrostatic Discharge •... - Page 30 Device Description WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Table 18: EMC – Immunity to Interference Standard Test Value Line Frequency Disturbances • EN 60255-26 Class A (150 V conductor/conductor / 300 V conductor/ground) Alternating Components of the Voltage to DC Line Connections •...
-
Page 31: Table 19: Emc - Emission Of Interference
WAGO-I/O-SYSTEM 750 XTR Device Description 750-427/040-000 2DI 110V DC 3ms XTR Table 19: EMC – Emission of Interference Standard Test Value Enclosure Emission of Interference • EN 61000-6-3 30 dB(µV/m), QP, 30 MHz … 230 MHz • EN 55032 Class B 37 dB(µV/m), QP, 230 MHz …... -
Page 32: Table 20: Standards And Rated Conditions For Rail Applications (En 50155)
EN 50121-3-2 5.5 EMC (Emission of Interference, EN 50121-3-2 Immunity to Interference) EN 50121-4 EN 50121-5 9.11 Materials (Fire Protection) EN 45545-2 Hazard level HL3 WAGO is a company certified in accordance with the IRIS quality standard. Manual Version 1.2.1... -
Page 33: Process Image
WAGO-I/O-SYSTEM 750 XTR Process Image 750-427/040-000 2DI 110V DC 3ms XTR Process Image Table 21: Input Bits Bit 1 Bit 0 DI 2 DI 1 DI 1 Signal state DI 1 – digital input channel 1 DI 2 Signal state DI 2 – digital input channel 2 Manual Version 1.2.1... -
Page 34: Mounting
750-427/040-000 2DI 110V DC 3ms XTR Mounting Mounting Sequence Fieldbus couplers, controllers and I/O modules of the WAGO I/O SYSTEM 750 are snapped directly on a carrier rail in accordance with the European standard EN 60175 (DIN 35). The reliable positioning and connection is made using a tongue and groove system. -
Page 35: Inserting And Removing Devices
WAGO-I/O-SYSTEM 750 XTR Mounting 750-427/040-000 2DI 110V DC 3ms XTR Inserting and Removing Devices Do not touch hot surfaces! The surface of the housing can become hot during operation. If the device was operated at high ambient temperatures, allow it to cool off before touching it. -
Page 36: Removing The I/O Module
Mounting WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Press the I/O module into the assembly until the I/O module snaps into the carrier rail. Figure 8: Snap the I/O Module into Place (Example) With the I/O module snapped in place, the electrical connections for the data contacts and power jumper contacts (if any) to the fieldbus coupler/controller or to the previous or possibly subsequent I/O module are established. -
Page 37: Connect Devices
Only one conductor may be connected to each CAGE CLAMP Do not connect more than one conductor at one single connection! If more than one conductor must be routed to one connection, these must be connected in an up-circuit wiring assembly, for example using WAGO feed- through terminals. ®... -
Page 38: Connection Examples
Connect Devices WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Connection Examples 6.2.1 2 Channels, High-side Switching Figure 11: Connecting Diagram –2 Channels, High-side Switching 6.2.2 2 Channels, Low-side Switching Figure 12: Connecting Diagram –2 Channels, Low-side Switching Manual... -
Page 39: Channel High-Side Switching, 1 Channel Low-Side Switching
WAGO-I/O-SYSTEM 750 XTR Connect Devices 750-427/040-000 2DI 110V DC 3ms XTR 6.2.3 1 Channel High-side Switching, 1 Channel Low-side Switching Figure 13: Connecting Diagram – 1 Channel High-side Switching, 1 Channel Low-side Switching Manual Version 1.2.1... -
Page 40: Use In Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Use in Hazardous Environments The WAGO I/O SYSTEM 750 (electrical equipment) is designed for use in Zone 2 hazardous areas and shall be used in accordance with the marking and installation regulations. -
Page 41: Marking Configuration Examples
WAGO-I/O-SYSTEM 750 XTR Use in Hazardous Environments 750-427/040-000 2DI 110V DC 3ms XTR Marking Configuration Examples 7.1.1 Marking for Europe According to ATEX and IECEx Figure 14: Marking Example According to ATEX and IECEx Figure 15: Text Detail – Marking Example According to ATEX and IECEx Manual Version 1.2.1... -
Page 42: Table 22: Description Of Marking Example According To Atex And Iecex
Use in Hazardous Environments WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Table 22: Description of Marking Example According to ATEX and IECEx Marking Description TUEV 07 ATEX 554086 X Approving authority resp. certificate numbers IECEx TUN 09.0001 X... -
Page 43: Figure 16: Marking Example For Approved Ex I I/O Module According To Atex
WAGO-I/O-SYSTEM 750 XTR Use in Hazardous Environments 750-427/040-000 2DI 110V DC 3ms XTR Figure 16: Marking Example for Approved Ex i I/O Module According to ATEX and IECEx Figure 17: Text Detail – Marking Example for Approved Ex i I/O Module According to ATEX and... -
Page 44: Table 23: Description Of Marking Example For Approved Ex I I/O Module According To Atex And Iecex
Use in Hazardous Environments WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Table 23: Description of Marking Example for Approved Ex i I/O Module According to ATEX and IECEx Marking Description TUEV 12 ATEX 106032 X Approving authority resp. certificate numbers... -
Page 45: Marking For The United States Of America (Nec) And Canada (Cec)
WAGO-I/O-SYSTEM 750 XTR Use in Hazardous Environments 750-427/040-000 2DI 110V DC 3ms XTR 7.1.2 Marking for the United States of America (NEC) and Canada (CEC) Figure 18: Marking Example According to NEC Figure 19: Text Detail – Marking Example According to NEC 500... -
Page 46: Figure 20: Text Detail - Marking Example For Approved Ex I I/O Module
Use in Hazardous Environments WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Figure 20: Text Detail – Marking Example for Approved Ex i I/O Module According to NEC 505 Table 25: Description of Marking Example for Approved Ex i I/O Module According to NEC 505... -
Page 47: Figure 22: Text Detail - Marking Example For Approved Ex I I/O Modules
WAGO-I/O-SYSTEM 750 XTR Use in Hazardous Environments 750-427/040-000 2DI 110V DC 3ms XTR Figure 22: Text Detail – Marking Example for Approved Ex i I/O Modules According to CEC 18 attachment J Table 27: Description of Marking Example for Approved Ex i I/O Modules According to CEC 18... -
Page 48: Installation Regulations
Use in Hazardous Environments WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Installation Regulations For the installation and operation of electrical equipment in hazardous areas, the valid national and international rules and regulations which are applicable at the installation location must be carefully followed. - Page 49 WAGO-I/O-SYSTEM 750 XTR Use in Hazardous Environments 750-427/040-000 2DI 110V DC 3ms XTR Explosive atmosphere occurring simultaneously with assembly, installation or repair work must be ruled out. Among other things, these include the following activities • Insertion and removal of components •...
-
Page 50: Special Notes Regarding Ansi/Isa Ex
Use in Hazardous Environments WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR 7.2.2 Special Notes Regarding ANSI/ISA Ex For ANSI/ISA Ex acc. to UL File E198726, the following additional requirements apply: • Use in Class I, Division 2, Group A, B, C, D or non-hazardous areas only •... -
Page 51: List Of Figures
WAGO-I/O-SYSTEM 750 XTR List of Figures 750-427/040-000 2DI 110V DC 3ms XTR List of Figures Figure 1: View ...................... 17 Figure 2: Data Contacts ..................18 Figure 3: Power Jumper Contacts ............... 19 ® Figure 4: CAGE CLAMP Connectors ..............20 Figure 5: Display Elements .................. -
Page 52: List Of Tables
List of Tables WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR List of Tables Table 1: Number Notation ..................8 Table 2: Font Conventions ..................8 Table 3: Legend for Figure “View” ............... 17 Table 4: Legend for Figure “Power Jumper Contacts” ......... 19 ®... - Page 53 WAGO-I/O-SYSTEM 750 XTR 750-427/040-000 2DI 110V DC 3ms XTR Manual Version 1.2.1...
- Page 54 WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 • D - 32385 Minden Hansastraße 27 • D - 32423 Minden Phone: +49 571 887 – 0 Fax: +49 571 887 – 844169 E-Mail: info@wago.com Internet: www.wago.com...
Need help?
Do you have a question about the 750-427/040-000 and is the answer not in the manual?
Questions and answers