Daikin Altherma 3 H HT F Series Installer's Reference Manual page 254

10/11
Field settings table
Breadcrumb Field code Setting name
9.I [7-03] --
9.I [7-04] --
9.I [7-05] Boiler efficiency
9.I [7-06] HP Forced OFF
9.I [7-07] BBR16 activation (#)
9.I [8-00] Minimum running time for domestic hot water operation.
9.I [8-01] Maximum running time for domestic hot water operation.
9.I [8-02] Anti-recycling time.
9.I [8-03] Booster heater delay timer.
9.I [8-04] Additional running time for the maximum running time.
9.I [8-05] Allow modulation of the LWT to control the room temp?
9.I [8-06] Leaving water temperature maximum modulation.
9.I [8-07] What is the desired comfort main LWT in cooling?
9.I [8-08] What is the desired eco main LWT in cooling?
9.I [8-09] What is the desired comfort main LWT in heating?
9.I [8-0A] What is the desired eco main LWT in heating?
9.I [8-0B] --
9.I [8-0C] --
9.I [8-0D] --
9.I [9-00] What is the maximum desired LWT for main zone in heating?
9.I [9-01] What is the mimimum desired LWT for main zone in heating?
9.I [9-02] What is the maximum desired LWT for main zone in cooling?
9.I [9-03] What is the mimimum desired LWT for main zone in cooling?
9.I [9-04] Leaving water temperature overshoot temperature.
9.I [9-05] What is the mimimum desired LWT for add. zone in heating?
9.I [9-06] What is the maximum desired LWT for add. zone in heating?
9.I [9-07] What is the mimimum desired LWT for add. zone in cooling?
9.I [9-08] What is the maximum desired LWT for add. zone in cooling?
9.I [9-0C] Room temperature hysteresis.
9.I [9-0D] Pump speed limitation
9.I [9-0E] --
9.I [C-00] Domestic heating water priority.
9.I [C-01] --
9.I [C-02] Is an external backup heat source connected?
9.I [C-03] Bivalent activation temperature.
9.I [C-04] Bivalent hysteresis temperature.
9.I [C-05] What is the thermo request contact type for the main zone?
9.I [C-06] What is the thermo request contact type for the add. zone?
9.I [C-07] What is the unit control method in space operation?
9.I [C-08] Which type of external sensor is installed?
9.I [C-09] What is the required alarm output contact type?
9.I [C-0A] --
9.I [C-0B] --
9.I [C-0C] --
9.I [C-0D] --
9.I [C-0E] --
9.I [D-00] Which heaters are permitted if prefer. kWh rate PS is cut?
4P586458-1 - 2019.07
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(#) Only applicable in Swedish language.
Range, step
Default value
2.5
0
0: Very high
1: High
2: Medium
3: Low
4: Very low
0: Disabled
1: Enabled
0: Disabled
1: Enabled
0~20 min, step 1 min
1 min
5~95 min, step: 5 min
30 min
0~10 hour, step: 0,5 hour
0,5 hour [E-07]=1
3 hour [E-07]≠1
20~95 min, step: 5 min
50 min
0~95 min, step: 5 min
95 min
0: No
1: Yes
0~10°C, step: 1°C
5°C
[9-03]~[9-02], step: 1°C
18°C
[9-03]~[9-02], step: 1°C
20°C
[9-01]~[9-00], step: 1°C
35°C
[9-01]~[9-00], step: 1°C
33°C
13
10
16
[2-0C]=2:
37~70, step: 1°C
70°C
[2-0C]≠2:
37~55, step: 1°C
55°C
15~37°C, step: 1°C
25°C
18~22°C, step: 1°C
22°C
5~18°C, step: 1°C
7°C
1~4°C, step: 1°C
1°C
15~37°C, step: 1°C
25°C
[2-0D]=2:
37~70, step: 1°C
70°C
[2-0D]≠2:
37~55, step: 1°C
55°C
5~18°C, step: 1°C
7°C
18~22°C, step: 1°C
22°C
1~6°C, step: 0,5°C
1 °C
0~8, step:1
0 : No limitation
1~4 : 50~80%
5~8 : 50~80% during sampling
6
6
0: Solar priority
1: Heat pump priority
0
0: No
1: Bivalent
-25~25°C, step: 1°C
0°C
2~10°C, step 1°C
3°C
0: -
1: 1 contact
2: 2 contacts
0: -
1: 1 contact
2: 2 contacts
0: LWT control
1: Ext RT control
2: RT control
0: No
1: Outdoor sensor
2: Room sensor
0: Normally open
1: Normally closed
0
0
0
0
0
0: None
1: BSH only
2: BUH only
3: All heaters
Installer setting at variance with
default value
Date
Official Value
(*1) *6V_(*2) *9W_
(*3) ETB*_(*4) ETV*_
(*5) *X*_(*6) *H*