Table of Contents
Advertisement
Quick Links
P5-20...R40-17
Model: E16-V1
Assembly and Operating Instructions
en
Sun protection drives with locking system
Important information for:
• Fitters / • Electricians / • Users
Please forward accordingly!
These instructions must be kept safe for future reference.
2010 301 019 0a 22/01/2018
Becker-Antriebe GmbH
Friedrich-Ebert-Straße 2-4
35764 Sinn/Germany
www.becker-antriebe.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Becker E16-V1
Summary of Contents for Becker E16-V1
- Page 1 P5-20...R40-17 Model: E16-V1 Assembly and Operating Instructions Sun protection drives with locking system Important information for: • Fitters / • Electricians / • Users Please forward accordingly! These instructions must be kept safe for future reference. 2010 301 019 0a 22/01/2018 ...
-
Page 2: Table Of Contents
Table of contents General .................................... 3 Warranty ..................................... 3 Safety instructions ................................ 4 Instructions for the user.............................. 4 Instructions for installation and commissioning........................ 4 Intended use .................................. 6 Assembling and disassembling the plug-in connecting cable.................... 6 Assembling the plug-in connecting cable .......................... 6 Disassembling the plug-in connecting cable for tubular drives dia. -
Page 3: General
General These tubular drives are high-quality products with the following features: • Optimised for sun protection applications with locking system • freely programmable locking and unlocking limit position • Automatic detection of upper limit position • Automatic detection of lower limit position when the locking system is activated •... -
Page 4: Safety Instructions
Safety instructions The following safety instructions and warnings are intended to avert hazards and to prevent property damage and personal injury. Instructions for the user General information • The drive must be disconnected from its power source during cleaning and maintenance and when re- placing parts. - Page 5 • Hazardous moving parts of the drive must be installed at a height of over 2.5 m above floor level or any other surface from which the drive can be accessed. • To ensure safe operation of the system after commissioning, the limit positions must be correctly set/ programmed in.
-
Page 6: Intended Use
Intended use The type of tubular drive described in these instructions is intended solely for the operation of sun protection systems with locking system. To function properly, these tubular drives need a fixed stop in the upper limit position (retracted sun protection). It may only be used in networked systems if all the individual drives are exactly synchronised and reach the limit positions at the same time. -
Page 7: Disassembling The Plug-In Connecting Cable For Tubular Drives Dia. 35
Disassembling the plug-in connecting cable for tubular drives dia. 35. Caution Prior to disassembly, the power supply to the connecting cable must be disconnected. Insert a suitable flathead screwdriver between the locating lug and the snap-in pin, so that the snap-in pin releases the locating lug from the plug. -
Page 8: Disassembling The Plug-In Connecting Cable For Tubular Drives Dia. 45 And Dia. 58
Disassembling the plug-in connecting cable for tubular drives dia. 45 and dia. 58 Caution Prior to disassembly, the power supply to the connecting cable must be disconnected. Insert a suitable flathead screwdriver right into the recess of the locating latch, so that the latch releases the locating lug from the plug. -
Page 9: Installation
Installation Assembling the drive Attention To connect the drive to the driven part, solely mechanical accessory components made by the drive manufacturer from the current product catalogue may be used. Prior to mounting, the fitter must ensure that the masonry and the system being motorised are sufficiently robust (drive torque plus weight of the shading solution). -
Page 10: Disassembling The Drive Adapter With Safety Catch On The Drive Shaft
Disassembling the drive adapter with safety catch on the drive shaft Disassembly with disassembly tool, Item no. 4930 300 606 0 Disassembly with long nose pliers Assembling and disassembling the drive adapter with separate drive adapter safety catch Assembling and disassembling the drive adapter with screw connection Mounting the drive in the tube For profile tubes: In the case of some drive adapters, tolerances of the groove widths in different bar-... - Page 11 For round shafts: Measure the lug of the thrust ring (X, Y). Then notch the tube on the motor side, so the lug of the thrust ring can also be pushed into the shaft. There must be no play between the lug of the thrust ring and the shaft. To ensure secure torque transmission for round shafts, we recommend screwing the drive adapter to the shaft (see the table below).
-
Page 12: Setting The Limit Positions Using The Programming Unit
Setting the limit positions using the programming unit Programming button Travel button black black brown brown blue blue green-yellow green-yellow Unlocked Locked Locking bolt Moving part of the locking system on the front section of the sun protection system Bolt mechanism Fixed part of the locking system in the guide track of the sun protection system Connect the wires of the tubular drive to those of the same colour in the programming unit (Item No. -
Page 13: Deleting The Limit Positions Using The Programming Unit
Use the travel button to run the bolt in the open direction until it is engaged by the bolt mechanism. ▻ The tubular drive switches off automatically. Use the travel button to run the bolt in the down direction and disengage it from the bolt mechanism, then stop the tubular drive. -
Page 14: Adjusting The Limit Positions With A Rotary Switch Or A Locking Button
Adjusting the limit positions with a rotary switch or a locking button black black brown brown blue blue green-yellow green-yellow Unlocked Locked Locking bolt Moving part of the locking system on the front section of the sun protection system Bolt mechanism Fixed part of the locking system in the guide track of the sun protection system Connect the wires of the tubular drive to those of the same colour in the rotary switch or a locking button and switch on the power supply. -
Page 15: Deleting The Limit Positions With A Rotary Switch Or A Locking Button
Run the bolt past the locking point and stop the tubular drive. Carry out the following sequence without interruption between the individual drive commands. ▻ The locking limit position is now saved and the tubular drive makes a "click" sound to confirm. until STOP and hold until Use the travel button to run the bolt in the open direction until it is engaged by the bolt mechanism. -
Page 16: Obstacle Detection (For Vertical Sun Protection Applications With Heavy End Strip)
Obstacle detection (for vertical sun protection applications with heavy end strip) The functions and presettings of the model versions are different. Please find further in- formation in the "Version summary" chapter. Caution Obstacle detection is only active in conjunction with the "drive adapter for obstacle detec- tion". -
Page 17: Maintenance
Maintenance These drives are maintenance-free. Version summary Function Model version E16-V1 Ø45 8-40Nm Automatic adjustment of direction of rotation Obstacle detection Increased closing force (stop behaviour) Changing the stop behaviour function with the programming unit Fabric untensioning Fabric tensioning Reduced fabric tensioning... -
Page 18: Technical Data Dia. 45
Technical data dia. 45 Tubular drive R8-17 R12-17 R20-17 R30-17 R40-17 Model E16-V1 Type C SEO I3 Rated torque [Nm] Output speed [rpm] Limit switch range 64 revolutions Supply voltage 230 V AC / 50 Hz Connected load [W] Rated current consumption [A] 0.45 0.50... -
Page 19: Sample Wiring Diagram
Sample wiring diagram The assignment of the black and brown wires according to the direction of travel is de- pendant on how the drive is installed (mounted to the right or to the left). Controlling one/several drive(s) via a single switch/button... -
Page 20: Declaration Of Conformity
Declaration of conformity...
Need help?
Do you have a question about the E16-V1 and is the answer not in the manual?
Questions and answers