Peninsula Installation - EcoSmart Fire FLEX Series Clearances And Installation Manual

ENGLISH
Peninsula
Installation
Equipment required: Power Drill, Screwdriver, Level, Hand Trowel for
Plaster, Silicone Gun, Caulk Gun
1. Construct a main wall framework with the opening size shown in
Table E. The base of the frame can be a solid bench/platform, which
will assist in leveling up the appliance when in position.
WARNING: Three-sided appliances cannot be inserted into a
one-way cavity wall, it must be a two-way cavity where the glass
on all sides are free from obstructions. Do not apply pressure or
materials to the glass. Triple sided appliances are designed as
room divider inserts. If you do not comply with this installation
instruction the wall could overheat and catch fire.
Table E: Framework Opening Sizes
Physical appliance dimensions should be verified against cut out dimensions BEFORE
installation begins to confirm tolerances align.
W
APPLIANCE
mm [in]
FLEX18PN 470 [18.5]
FLEX32PN 902 [35.5]
FLEX42PN 1157 [45.5]
FLEX50PN 1362 [53.6]
FLEX50PN.BX
1362 [53.6]
FLEX60PN.BX
1617 [63.7]
FLEX68PN
1822 [71.7]
FLEX68PN.BX
1822 [71.7]
FLEX68PN.BX2
1822 [71.7]
FLEX78PN.BX2
2077 [81.8]
FLEX86PN
2282 [89.8]
FLEX86PN.BX
2282 [89.8]
FLEX86PN.BX2 2282 [89.8]
FLEX104PN 2742 [107.9]
FLEX104PN.BX 2742 [107.9]
FLEX104PN.BX2 2742 [107.9]
FLEX122PN
3202 [126.1]
FLEX122PN.BX
3202 [126.1]
FLEX122PN.BX2
3202 [126.1]
FLEX140PN.BX
3662 [144.2]
FLEX140PN.BX2
3662 [144.2]
FLEX158PN
4122 [162.3]
FLEX158PN.BX2
4122 [162.3]
* Appliance weight includes burner/s (dry weight excluding fuel), glass charcoal and glass. It
does NOT include glass charcoal for side boxes.
IMPORTANT: The framing above the appliance must be self-
supporting. The appliance is not load-bearing.
www.ecosmartfire.com
D H Weight*
mm [in] mm [in] kg [lbs]
349 [13.6] 730 [28.7] 34.2 [75.2]
349 [13.6] 730 [28.7] 49.8 [109.6]
349 [13.6] 730 [28.7] 64.7 [142.3]
349 [13.6] 730 [28.7] 59.1 [130]
349 [13.6] 730 [28.7] 73.2 [161]
349 [13.6] 730 [28.7] 87.5 [192.5]
102.8 [226.2]
349 [13.6] 730 [28.7]
83.9 [184.6]
349 [13.6] 730 [28.7]
96.1 [211.4]
349 [13.6] 730 [28.7]
110.4 [242.9]
349 [13.6] 730 [28.7]
102.5 [225.5]
349 [13.6] 730 [28.7]
124.1 [273]
349 [13.6] 730 [28.7]
349 [13.6] 730 [28.7] 108.7 [239.1]
349 [13.6] 730 [28.7] 153.3 [337.3]
349 [13.6] 730 [28.7] 127.3 [280.1]
349 [13.6] 730 [28.7] 147.3 [324.1]
349 [13.6] 730 [28.7] 145.8 [320.8]
349 [13.6] 730 [28.7] 176.2 [387.6]
152.1 [334.6]
349 [13.6] 730 [28.7]
170.6 [375.3]
349 [13.6] 730 [28.7]
198.7 [437.1]
349 [13.6] 730 [28.7]
231.8 [510]
349 [13.6] 730 [28.7]
195.4 [429.9]
349 [13.6] 730 [28.7]
2. Remove the extension flange from the firebox so that both sides are
the same height. This will help make sliding the firebox into the frame
easier. Pay attention not to lose the screws, they will be needed again
when the flange is re-installed.
3. Slide the appliance into the framing cavity (the bottom tray can sit
directly on top of the frame). The appliance is shipped with red stability
bracket(s) on the open sides to keep the appliance square while in
transport and during installation. Keep these brackets on while framing
up the setting to assist in minimizing movement of the appliance.
4. Ensure that the back and open side edge of the appliance are flush
with frame studs.
5. Align the flange extension panel with the threaded holes on the
appliance. Screw it into place using the included screws (bottom row
onto appliance, top row onto framing material) to secure it into position.
FRONT VIEW
BACK VIEW