Double Sided Installation 11 -1 - EcoSmart Fire FLEX Series Clearances And Installation Manual

ENGLISH
Double Sided
Installation
Equipment required: Power Drill, Screwdriver, Level, Hand Trowel for
Plaster, Silicone Gun, Caulk Gun
1. Construct a main wall framework with the opening size shown in
Table D. The base of the frame can be a solid bench/platform, which
will assist in leveling up the appliance when in position.
WARNING: Double-sided appliances cannot be inserted into a
one-way cavity wall, it must be a two-way cavity where the glass
on both sides is free from obstructions. Do not apply pressure
or materials to the glass. Double sided appliances are designed
as wall divider inserts. If you do not comply with this installation
instruction the wall could overheat and catch fire.
Table D: Framework Opening Sizes
Physical appliance dimensions should be verified against cut out dimensions BEFORE
installation begins to confirm tolerances align.
W
APPLIANCE
mm [in]
FLEX18DB
488 [19.2]
FLEX32DB
922 [36.3]
FLEX42DB
1177 [46.3]
FLEX50DB
1380 [54.3]
FLEX50DB.BX
1380 [54.3]
FLEX60DB.BX 1634 [64.3]
FLEX68DB 1840 [72.4]
FLEX68DB.BX 1840 [72.4]
FLEX68DB.BX2 1840 [72.4]
FLEX78DB.BX2
2090 [82.3]
FLEX86DB
2300 [90.5]
FLEX86DB.BX
2300 [90.5]
FLEX86DB.BX2
2300 [90.5]
FLEX104DB
2760 [108.7]
FLEX104DB.BX
2760 [108.7]
FLEX104DB.BX2
2760 [108.7]
FLEX122DB
3220 [126.7]
FLEX122DB.BX 3220 [126.7]
FLEX122DB.BX2 3220 [126.7]
FLEX140DB.BX 3680 [144.9]
FLEX140DB.BX2 3680 [144.9]
FLEX158DB
4140 [163]
FLEX158DB.BX2
4140 [163]
* Appliance weight includes burner/s (dry weight excluding fuel), glass charcoal and glass. It
does NOT include glass charcoal for side boxes.
IMPORTANT: The framing above the appliance must be self-
supporting. The appliance is not load-bearing.
www.ecosmartfire.com
D H Weight*
mm [in] mm [in] kg [lbs]
26.5 [58.3]
349 [13.6] 730 [28.7]
46.6 [102.5]
349 [13.6] 730 [28.7]
61.4 [135.1]
349 [13.6] 730 [28.7]
70.8 [155.8]
349 [13.6] 730 [28.7]
70 [154]
349 [13.6] 730 [28.7]
349 [13.6] 730 [28.7] 83.3 [183.3]
349 [13.6] 730 [28.7] 95.5 [210.1]
349 [13.6] 730 [28.7] 83.7 [184.1]
349 [13.6] 730 [28.7] 94.8 [208.6]
349 [13.6] 730 [28.7] 106.2 [233.6]
349 [13.6] 730 [28.7] 102.3 [225.1]
124.5 [273.9]
349 [13.6] 730 [28.7]
108.5 [238.7]
349 [13.6] 730 [28.7]
145.7 [320.5]
349 [13.6] 730 [28.7]
127.1 [279.6]
349 [13.6] 730 [28.7]
142 [312]
349 [13.6] 730 [28.7]
145.6 [320.3]
349 [13.6] 730 [28.7]
349 [13.6] 730 [28.7] 170.1 [374.2]
349 [13.6] 730 [28.7] 151.9 [334.2]
349 [13.6] 730 [28.7] 170.4 [374.9]
349 [13.6] 730 [28.7] 192.9 [424.4]
349 [13.6] 730 [28.7] 226.8 [499]
349 [13.6] 730 [28.7] 195.2 [429.4]
2. Remove the extension flange from the firebox so that both sides are
the same height. This will help make sliding the firebox into the frame
easier. Pay attention not to lose the screws, they will be needed again
when the flange is re-installed.
3. Slide the appliance inside the framing cavity (the bottom tray can sit
directly on top of the frame). The appliance is shipped with red stability
bracket(s) installed on the open side(s) to keep the appliance square while
in transport and during installation. Keep the bracket(s) on while framing
up the setting to assist in minimising movement of the appliance.
4. Align the flange extension panel with the threaded holes on the
appliance. Screw it into place using the included screws (bottom row
onto appliance, top row onto framing material) to secure it into position.
5. Fix the appliance to the framework with screws using the existing
mounting holes on the appliance flanges. Make sure that the
appliance is level before securing it in place.
FRONT VIEW
BACK VIEW