Table of Contents
Related Manuals for HAWK ENTERPRISES HP1513-TEXHD
Summary of Contents for HAWK ENTERPRISES HP1513-TEXHD
- Page 1 HAWK TEXHD HAWK Severe Duty Floor Machine ENTERPRISES Stripping, Sanding, Carpet Care, Resurfacing Operation Care Service HAWK ENTERPRISES 2902 Park Six Court, Elkhart, IN 46514 (574) 294-1910 (888) 289-4295 www.hawkenterprises.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Machine Specifications ....................1 Service Information ....................2 Important Safety Instructions ...................2 Grounding Instructions ....................3 Operations / Accessories ..................3 Brush And Drive Block Installation ..............4 Adjustments......................4 Controls .......................5 Guidlines For Operation ..................5 Cord Storage .......................5 Clean Up And Storage .....................5 Floor Machine Assemblies ..................6 Floor Machine Parts List .................. -
Page 3: Service Information
SERVICE INFORMATION Do not allow the machine to be used as a toy. To obtain consistent performance over the life Close attention is necessary when used near of your equipment, read through these instruc- children. Do not leave the machine connected to tions and save them for future reference. -
Page 4: Grounding Instructions
GROUNDING INSTRUCTIONS This appliance must be grounded. If it should mal- function or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord that has an equipment-grounding conductor and grounding plug. -
Page 5: Brush And Drive Block Installation
BRUSH AND PAD DRIVER INSTALLATION UNLOCK NOTE: Disconnect the power cord from the LOCK electrical outlet before installing a brush or pad driver. Figure 5 Figure 4 To install a brush or pad driver, leave the handle in the upright position and tip the machine backwards UNLOCK so it rests on its wheels and upper handle section (Figure 4). -
Page 6: Guidlines For Operation
Push forward to disengage safety CORD STORAGE switch lock. When not in use, loosely wind the power cord around the cord storage hook on the handle shaft and both of the handle grips, as shown: Figure 7 GUIDELINES FOR OPERATON •... -
Page 7: Floor Machine Assemblies
HAWK BRUTE... - Page 9 DATA PLATE INFORMATION FRONT REAR PRODUCT PRODUCT IDENTIFICATION SAFETY LOGO LABEL LABEL KIT2020BLK 23 24 MOTOR POWER CORD SHOWN FOR REFERANCE ONLY...
-
Page 10: Optional Accessories
1/25/2016 PART HANDLE ASSY STD FLOOR MACHINE DET. NO: NUMBER DESCRIPION QTY. KIT3011BLK TRIGGER REPLACEMENT KIT 14 INCH BLK INC IN KIT3011BLK TRIGGER 14 INCH - BLACK INC IN KIT3011BLK ROLL PIN INC IN KIT3011BLK SPRING - TRIGGER KIT2011BLK HANDLE GRIP REPLACEMENT KIT INC IN KIT2011BLK HANDLE GRIP - BLK KIT1005... - Page 11 1/24/2015 DETAIL PART BRUTE / TEXHD MACHINE QTY. NUMBER NUMBER DESCRIPTION REQ'D KIT3012BLK FRAME STD. MACHINE INC IN KIT3012BLK FRAME STD. - 2 SPEED BLK SEE DATA PLATE FOR PROPER BRUSH COVER SIZE KIT3013RED BRUSH COVER 13 INCH W/BLK BUMPER INC IN KIT3013RED BUMPER 13 INCH BLK INC IN KIT3013RED...
-
Page 12: Limited Warranty
If repair is done on your equipment by anyone other than those designated as author- ized to perform such work without first having obtained factory instructions, HAWK ENTERPRISES at its sole option, my determine that this warranty will not apply and that reimbursement for such repair will not be made because of the failure to comply with such factory specified instructions.
Need help?
Do you have a question about the HP1513-TEXHD and is the answer not in the manual?
Questions and answers