HAWK ENTERPRISES HP1513-1500 Manual

HAWK ENTERPRISES HP1513-1500 Manual

High-speed, burnishing & refinishing

Advertisement

HAWK High-Speed
HAWK
Burnisher
ENTERPRISES
Burnishing & Refinishing
Operation
Care
Service
HAWK ENTERPRISES
2902 Park Six Court, Elkhart, IN 46514
(574) 294-1910
(888) 289-4295
www.hawkenterprises.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HP1513-1500 and is the answer not in the manual?

Questions and answers

Summary of Contents for HAWK ENTERPRISES HP1513-1500

  • Page 1 HAWK High-Speed HAWK Burnisher ENTERPRISES Burnishing & Refinishing Operation Care Service HAWK ENTERPRISES 2902 Park Six Court, Elkhart, IN 46514 (574) 294-1910 (888) 289-4295 www.hawkenterprises.com...
  • Page 2: Table Of Contents

    17” Standard 17” Dust Control 20” Standard 20” Dust Control Pad Size 13” 15” 17” 16” 20” 19” Speed 1500 RPM Model # HP1513-1500 HP1515-1500 HP1517-1500 HP1517-1500DC HP1520-1500 HP1520-1500DC Part # F1500-13 F1500-15 F1500-17 F1500-17DC F1500-20 F1500-20DC Amp Draw 9.1 Amp 9.6 Amp...
  • Page 3: Service Information

    SERVICE INFORMATION Do not allow the machine to be used as a toy. To obtain consistent performance over the life Close attention is necessary when used near of your equipment, read through these instruc- children. Do not leave the machine connected to tions and save them for future reference.
  • Page 4: Grounding Instructions

    GROUNDING INSTRUCTIONS This appliance must be grounded. If it should mal- function or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord that has an equipment-grounding conductor and grounding plug.
  • Page 5: Brush And Drive Block Installation

    PAD DRIVER INSTALLATION NOTE: Disconnect the power cord from the electrical outlet before installing a pad driver. Adjustment Screws Figure 6 ADJUSTMENTS HANDLE ADJUSTMENT Figure 4 To install a pad driver, leave the handle in the The handle can be adjusted to any desired work upright position and tip the machine backwards so it position by simply pushing up on the handle lock rests on its wheels and upper handle section (Figure...
  • Page 6: Controls

    CONTROLS • pad surface level, balanced, and flat on the floor at ON/OFF POWER SWITCH TRIGGERS all times. • Always adjust the operating handle to a comfort- The ON/OFF switch is conveniently located in the able height at which the brush or pad surface is form of dual triggers underneath the handle grips.
  • Page 10: Optional Accessories

    NUMBER NUMBER 115 VOLT UNITS REQ'D L0010 MOTOR DRIP COVER LABEL L0006 1500 RPM / CAUTION LABEL L0020 2000 RPM / CAUTION LABEL E0027 (115 VOLT) MOTOR DC 115 VOLT/50/60 CYCLE S0016 ROLLED MOTOR SCREEN H0049 SPRING (EXTENSION) ZINC H0040 SCREW 10-24 X .50 2+1+1+1+1 H0020...
  • Page 11 NUMBER NUMBER 115 VOLT UNITS REQ'D H0060 WASHER 5/16 FLAT ZINC H0043 BOLT 3/8 - 16 X 1-1/2 H.C.S. GR5 ZINC S0018P CONNECTING LEG H0028 GROMMET HP0003-BLACK CAM LOCK ASSEMBLY -(BLACK) WASHER SLOTTED BOLT SPADE-ZINC RIVET SOLID -ZINC NUT PUSH BRIGHT NICKEL HANDLE LOCK CAM-BLACK HP0004-1BLACK HANDLE LOCK CAP KIT (BLACK)
  • Page 12: Limited Warranty

    If repair is done on your equipment by anyone other than those designated as author- ized to perform such work without first having obtained factory instructions, HAWK ENTERPRISES at its sole option, my determine that this warranty will not apply and that reimbursement for such repair will not be made because of the failure to comply with such factory specified instructions.

Table of Contents