Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly. Along with a wide range of accessories...
CONTENTS Contents 4 Safety information 6 Installation 12 Product description 13 Operation 14 Helpful hints and tips 15 Care and cleaning 16 What to do if… 17 Technical data 18 Environment concerns The following symbols are used in this user manual: Important information concerning your personal safety and information on how to...
Safety information SAFETY INFORMATION WARNING! These instructions are only valid in the countries whose symbols appear on this booklet's cover. For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it.
• Pots must not enter the control zone. • Do not use not stable cookware to prevent from tilt and accident. • Do not put flammable products or items that are wet with flammable products, and/or fusible objects (made of plastic or aluminium) and/or fabrics in, near or on the appliance. There is the risk of explosion or fire.
Installation • This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. Particular attention must be given to the relevant requirements regarding ventilation. • The use of a gas cooking appliance cause heat and moisture in the room in which it is installed.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regula- tions (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Instal- lation I.S.
Installation End of shaft with nut Washer Elbow Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or cop- per. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation.
1. Light the burner. 2. Turn the knob on the minimum position. 3. Remove the knob. 4. With a thin screwdriver, adjust the by-pass screw position. The by-pass screw – If you change from natural gas 20 mbar to liquid gas, fully tighten the adjustment screw in.
Installation This hob is designed to be connected to a 230 V 50 Hz AC electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate. The rating plate is located on the bottom of the hob. The hob is supplied with a 3 core flexible supply cord incorporating a 3 amp plug fitted.
Replacement of the connection cable To replace the connection cable use only H05V2V2-F T90 or equivalent type. Make sure that the cable section is applicable to the voltage and the working temperature. The yellow/ green earth wire must be approximately 2 cm longer than the brown (or black) phase wire. Building In min.
Product description b) Space for connections Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit.
OPERATION Ignition of the burner WARNING! Be very careful when you use open fire in kitchen environment. Manufacturer decline any responsibility in case misuse of the flame Always light the burner before you put cookware. To light the burner: 1. Turn the control knob counterclockwise to the maximum position ( down.
Helpful hints and tips If the burner accidentally goes out, turn the control knob to the off position and try to light the burner again after minimum 1 minute. The spark generator can start automatically when you switch on the mains, after installa- tion or a power cut.
CARE AND CLEANING WARNING! Switch the appliance off and let it cool down before you clean it. Disconnect the appliance from the electrical supply, before carrying out any cleaning or maintenance work. WARNING! For safety reasons, do not clean the appliance with steam cleaners or high-pressure clean- ers.
What to do if… Cleaning of the spark plug This feature is obtained through a ceramic ignition candle with a metal electrode. Keep these components well clean to prevent difficult lighting and check that the burner crown holes are not obstructed. Periodic maintenance Periodically speak your local Service Force Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted.
Labels supplied with the accessories bag Stick the adhesive labels as indicated below: MOD. MOD. PROD.NO. PROD.NO. SER.NO SER.NO DATA DATA MODEL Stick it on Guarantee Card and send this part Stick it on Guarantee Card and keep this part Stick it on instruction booklet These data are necessary to help you quickly and correctly.
Environment concerns TOTAL POWER: Electric supply: Gas connection: Category: Gas supply: Appliance class: By-pass diameters Burner Auxiliary Semi-rapid Gas burners NORMAL POWER BURNER Auxiliary burner Semi-rap- id burner 3.0 (natural Rapid gas) burner 2.8 (LPG) ENVIRONMENT CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
please contact your local council, your household waste disposal service or the shop where you purchased the product. Packaging material The packaging materials are friendly to the environment and can be recycled. The plastic components are identified by marking: >PE<,>PS<, etc. Discard the packaging materials as household waste at the waste disposal facilities in your municipality.