Subscribe to Our Youtube Channel
Related Manuals for Marson mt850
Summary of Contents for Marson mt850
- Page 1 2D Wireless Barcode Scanner Quick Guide 2D Wireless Barcode Scanner Quick Guide (Rev3) P/N: 8013-0076000...
- Page 2 WARNING AND CAUTION FCC WARNING STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the 1. Take any metals into contact with the terminals in connectors. following two conditions: (1) this device may not cause harmful interference, and (2) 2.
-
Page 3: Specifications
OUT OF THE BOX INTRODUCTION Micro USB port Trigger Button (w/ Protective Cover) LED Indicator (1) iOS Hotkey Button (2) Delete Button Exit Window 2D Wireless Quick Guide & SPECIFICATIONS Barcode Scanner Quick Connection Card Illumination White LED Aimer Visible Red LED Scan rate 120 frames/sec Sensor... -
Page 4: Led Indication
BEEPER INDICATION GETTING STARTED Single beep Good read Single short beep The scanner reads a Code39 of ASCII in configuration procedure Two beeps i. Wireless connection ii. The scanner successfully reads a configuration barcode Three beeps Wireless disconnection ... - Page 5 INTERFACE INTERFACE There are 5 interfaces for data transmission/collection: . E043$ *.E043$* BT HID 1. BT HID - Emulates a Bluetooth HID keyboard that transmits each barcode data to the host after decode. (See page 9) 2. BT SPP - Emulates a Bluetooth SPP device that transmits .
-
Page 6: Getting Connected
GETTING CONNECTED PINCODE SETUP There are two modes of wireless communication: . E043$ STEP 1 . E032$ [ Recommanded ] *.E043$* *.E032$* BT mode - HID Pincode Start 1. Press the trigger for 1 second to activate the scanner. 2. Scan [DISCONNECT] STEP 2 3. -
Page 7: Numeric Bar Codes
NUMERIC BARCODES - 11 - - 12 -... - Page 8 SMARTPHONE/TABLET CONNECTION SMARTPHONE/TABLET TOUCH KEYBOARD Getting Connected - iOS & Android Touch Keyboard - iOS iOS Hotkey Button 1. Press the trigger for 1 second to power up the scanner. 2. Scan below configuration barcode to clear last pairing record. .
- Page 9 POWER OFF TIMEOUT BINARY CHECK CHARACTER The timeout of inactivity before auto power-off. . E029$ *.e029$* Variable Timeout ENABLE . B030$ *.B030$* . E030$ SET MINUTE *.e030$* (Range: 00 ~ 60) DISABLE . B029$ *.B029$* SET SECOND Once enabled, a checksum will be added to the end of each data to conduct Xor calculation.
- Page 10 GENERAL SETTINGS READING MODE . A001$ . F002$ TRIGGER DEFAULT . F007$ . P023$ *.F007$* AUTO-SENSING ABORT . A007$ CHECK VERSION BEEPER VIBRATOR . F012$ . D035$ *.D035$* VIBRATOR OFF BEEP OFF . F019$ . D034$ *.F019$* *.D034$* BEEP ON VIBRATOR ON - 17 - - 18 -...
- Page 11 KEYBOARD LAYOUT . C009$ . C010$ ENGLISH JAPAN (USA) (106 key) . C018$ . C025$ ENGLISH CANADIAN (UK) (FRENCH) . C034$ . C012$ CANADIAN FRENCH (TRADITIONAL) . C029$ . C011$ GERMAN NORWEGIAN . C026$ . C014$ ITALIAN SWEDISH . C031$ .
- Page 12 KEYBOARD LAYOUT . C017$ . C030$ CZECH BELGIAN (QWERTY) (AZERTY) . C022$ . C028$ CZECH DUTCH (QWERTZ) . C021$ . C027$ HUNGARIAN DANISH (QWERTZ) . C024$ . C032$ HUNGARIAN SLOVAK (101 KEY) . C033$ . C016$ SWISS BRAZILIAN (GERMAN) (PORTUGUESE) .
-
Page 13: Caps Lock On
ENABLE/DISABLE SYMBOLOGIES INVERSE BARCODE . D021$ . A002$ DISABLE *.D021$* ENABLE INVERSE BARCODE ALL CODE . G036$ . D022$ *.G036$* *.D022$* ENABLE ALL ENABLE 1D CODE INVERSE BARCODE . G038$ CAPSLOCK *.G038$* ENABLE ALL 2D CODE . A005$ *.A005$* . A003$ CAPSLOCK OFF *.A003$* DISABLE... -
Page 14: Memory Mode
TERMINATOR MEMORY MODE . D012$ . C035$ *.c035$* Memory Mode . D011$ After scanning the above barcode, the scanner will be able to collect barcode data off-line. The barcode data will be stored in the format of: < Date >, < Time >, < Barcode Data > < CR > To retrieve stored data, please connect the scanner to the host with cable, . - Page 15 MEMORY MODE MEMORY MODE . R011$ . R006$ *.R006$* *.R011$* SET DATE DATA FORMAT The default Data Format is <Date>, <Time>, <Barcode Data> Example: To set Date to 2021-08-01 (Year-Month-Day): below are the codes for each item: 1. Scan [Set Date] 2.
- Page 16 MEMORY MODE MEMORY MODE . R008$ . R009$ *.R008$* *.R009$* DATE FORMAT TIME FORMAT The default Date Format is DD/MM/YYYY (Code = 09), below The default Time Format is HH:MM:SS (Code = 01), below is full list of available formats and their setup codes: are available formats and their setup codes: Code Format...
- Page 17 QR Code Micro QR Code PDF417 Data Matrix Aztec - 31 - - 32 -...
Need help?
Do you have a question about the mt850 and is the answer not in the manual?
Questions and answers