Safety Warnings - BorMann PRO BIW1300 User Manual

EN

Safety Warnings

Warning: Please read the follow safety warning before operation.
All to defend and other
Ear cap shall be put on when welding, and very operation is also important during welding. So:
1. The welding helmet, face shield and protective goggles shall be prepared, when in the working area at any time.
2. The appropriate face shield with filter and skin face shall be used to protect eyes, face, neck, and ears form electrical spark and arc ray. And the spectator
should not watch the arc and keep rain sack away from the arc ray and splash.
3. The appropriate protective clothing, shoes and helmet shall be worn to protect from arc ray, sparing and splattering.
4. All the buttons shall oe done up to avoid the sparking and splattering.
5. The nonflammable partition and door curtain shall be used protect the other workers from electric ray and sparking.
6. The protective goggles shall be used when cleaning welding spatter.
Fire and Burse
The heat of frame and arc can cause fire So:
1. Keep the flammable materials including wooden, cloth, wet fuel and gas fuel and so on away from the welding working area.
2. All the walls and floor in the working area should be untracked to avoid the smoldering and fire.
3. Ensure that all the working pieces are cleared before doing welding, and do not do weld on the sealed container to avoid burst.
4. The fire-fighting equipment shall be prepared near the welding working area.
5. Do not use the equipment overloading.
6. The fire monitor shall be used after welding.
Electric shock
Please do not use the welding source in the wet area to avoid any injure or death So:
1. To ensure the source underpan and earthing system of input source are connected.
2. To ensure the working pieces and good electric are connected.
3. To ensure the working cable and working piece are connected.
4. To change the damaged or abrasion cable in time.
5. Keep dry, including cloth, working area, wire, welding torch, soldering turret and power supply.
6. Keep the body insulated from the work piece and ground.
7. The operator shall stand on a dry wooden board or insulating platform of rubble shoes when working in a sealed on moist area.
8. The dry and sealed glove snail be wore before turning on the power.
9. The power should be turned off before taking off the glove.
Safely Warning
Electromagnetic field
It can bring dangerous. So:
1. The worker that the heart pacemaker imbedded shall do some consultation with the doctor before doing welding; because the electromagnetic field may
disturb the normal work of have pacemaker.
2. The electromagnetic is unhealthful.
3. The worker shall take the following measures to down times exposing himself to the electromagnetic field:
(1) Put the electrode cause and work cable together, and also the tape can used if possible.
(2) Do not wind the welding touch cable and work cable round yourself.
(3) Put the welding torch cable and work cable on one side of yourself.
(4) Connect the work cable to the work piece, and make it to the welding area as nearly as possible.
(5) Make yourself away from welding source and cable as much as possible.
Fog and gas
The welding fog and gas can make the worker uncomfortable, on hunted, especially In the limited icescape, so do not breathe the fog and gas. So:
1. The aerator natural on mechanical shall be prepared in the working area. Do not do welding on the following metals (galvanized, seed, stainless steel,
copper, zinc, read, beryllium or calcium), and also do not breathe the welding fog and gas in.
2. Does not welding near the degreasing or spraying operation to avoid the poisonous gas phosgene or other imitates gas.
3. If you feel little imitate to the eyes, nose or threat. You shall stop welding and perfect the aerator. And you should stop welding at once if feeling comfort-
lessness.
Equipment maintenance
The wrong or inappropriate equipment maintenance can cause injury or death. So:
1. The licensed people can do assembly, maintenance and some other operation.
2. The power source shall be turned off when any maintenance work in the power source needed.
3. Ensure that the cable, earth wire, connector, main lead and power supply are in the normal work.
4. Do not abuse equipment and firing.
5. Keep the safe equipment and cabinet dos shall in peace and good condition.
6. Do not change any equipment.
2
WWW.BORMANNTOOLS.COM