Related Manuals for BUSCH SECO SV 1010
Summary of Contents for BUSCH SECO SV 1010
- Page 1 MAINTENANCE REPAIR MANUAL SECO SV 1010, SV 1016, SV 1025 and SV 1040 C Version...
-
Page 3: Table Of Contents
We reserve the right to change the product at any time without any form of notification. The information in this pub- lication is accurate to the best of our ability at the time of printing. Busch, Inc. will not be responsible for errors... -
Page 4: Introduction
Series vacuum pumps models SV 1010 C, SV 1016 C, operate oil-free. SV 1025 C and SV 1040 C (see Fig. 1). The Busch CAUTION: Do not allow any oil, grease, liq- Seco SV pump is an oil-free single-stage, rotary dry uid or vapor to enter the pump. -
Page 5: Service And Parts
27 mm / 1.063 inch A complete inventory of spare parts is maintained at SV1016 27 mm / 1.063 inch Busch, Inc. at all times. Parts will be shipped immedi- SV1025 33 mm / 1.339 inch ately upon request. SV1040 33 mm / 1.339 inch... -
Page 6: Plastic Filter Cover And Filter Housing
Allen wrenches: 5 mm Open end wrench: 10 mm Soft hammer: med. size, plastic or rubber Gear puller - push-pull type Motor shaft support tool (see Fig. 13) Socket set with 10 mm socket Feeler blades: .06 mm, .07 mm, .09 mm Emery cloth: 180 grit Flat honing stone Cleaning agent: acetone or similar... -
Page 7: Rotor
Note: The heads of the screws are located down inside the cylinder cavity. Screws Fig. 12 - Rotor Removal Fig 10 - Cylinder Removal CLEANING AND INSPECTION Rotor General CAUTION: Do not pull the rotor from the Use compressed air to blow off all parts. When neces- motor shaft by exerting force on any sur- sary, soak the parts in a degreasing solution, agitate face other than the rotor and the end of the... -
Page 8: Cylinder
resting on the point of the motor shaft support tool (see Fig. 13). Fig. 13 - Motor Shaft Support Tool CAUTION: The use of the motor shaft tool prevents side load damage to the motor bearings when the rotor is tapped into posi- tion. -
Page 9: Vanes
We highly recommend the use of Busch parts to achieve documented performance and efficient opera- tion. The use of parts other than Busch could limit the life expectancy of the equipment and could void any warranties if they are the cause of any damage. -
Page 10: Clearances And Technical Data Chart
Clearances Chart Note: All dimensions are in millimeters Technical Data Chart Fig. 18 - Clearances and Technical Data... -
Page 11: Parts List
Parts List Ref. Description Qty. Ref. Description Qty. Motor Eye bolt Tolerance ring 42** Skt. hd. cap screw Rotor Rubber lifting eye bushing Vane Washer Alignment disk Stud (SV1025/SV1040 only) Hex head cap screw Lifting eye spacer Lock washer Rubber mounting gasket Plug Base plate Cylinder... -
Page 12: Assembly Drawing
Note: Vacuum relief valve not shown SV 1025 C Shown... -
Page 13: Busch Inc. Factory Service Centers
Busch Inc. Factory Service Centers California Illinois 13826 Struikman Road 430 Windy Point Drive Cerritos, CA 90703 Glendale Heights, IL 60139 Phone (562) 926-8422 Phone (630) 545-1310 Fax (562) 926-7262 Fax (630) 545-1384 service.ca@buschinc.com service.il@buschinc.com New Jersey Puerto Rico 39 Davis Street... - Page 16 Busch, Inc. 516 Viking Drive Virginia Beach, Virginia 23452 P/N 0872.915.364 Phone: (757) 463-7800 FAX: (757) 463-7407 Revision 01/06...