BUSCH SV 1063 B Installation And Operating Instructions Manual

Vacuum pumps

Advertisement

Installation and Operating
Instructions
Vacuum pumps
SV/ SD 1063 - 1080 B
Ateliers Busch S.A.
Zone industrielle
2906 Chevenez
Switzerland
0870513097 /
191211 / Original instructions / Modifications reserved

Advertisement

Table of Contents
loading

Summary of Contents for BUSCH SV 1063 B

  • Page 1 Installation and Operating Instructions Vacuum pumps SV/ SD 1063 - 1080 B Ateliers Busch S.A. Zone industrielle 2906 Chevenez Switzerland 0870513097 / 191211 / Original instructions / Modifications reserved...
  • Page 2: Table Of Contents

    EC Declaration of Conformity ....15 Busch – All over the World in Industry ....16...
  • Page 3: Product Description

    When the only after prior consultation with Busch. chambers are connected with the inlet channel, gas is drawn in, com- The vacuum pump is intended for the placement in a potentially pressed by the next rotation and then discharged.
  • Page 4: Versions

    Prior to handling the vacuum pump, these operating instructions must be read and understood. If anything remains to be clarified, please l Make sure that the suction connection/gas inlet and the gas dis- contact your Busch representative! charge/pressure connection are closed (refit the plugs the pump was delivered with)
  • Page 5: Installation Position And Space

    Please seek the advice from your Busch representative l Make sure that no temperature sensitive parts (plastics, wood, l Make sure that the discharge line either slopes away from the va-...
  • Page 6: Electrical Connection

    Conveying media with a higher density than air leads to an increased thermal and mechanical load on the vacuum pump and is permissible only after prior consultation with Busch. Star-star connection, multi-voltage motor (Low voltage): The vacuum pump is made for the intended use in potentially non-ex- plosive areas The vacuum pump is thermally suitable for continuous operation.
  • Page 7: Maintenance

    CAUTION CAUTION During operation the surface of the vacuum pump may reach tem- During operation the surface of the vacuum pump may reach tem- peratures of more than 100°C. peratures of more than 100°C. Risk of burns! Risk of burns! l Make sure that the vacuum pump is shut down and cannot be ac- The vacuum pump shall be protected against contact during opera- cidentally switched on again...
  • Page 8: Overhaul

    Risk of explosion! Approval for operation of the vacuum pumpwill be void! Any dismantling of the vacuum pump that goes beyond of what is described in this manual must be done by specially trained Busch service personnel only. Removal from Service...
  • Page 9: Troubleshooting

    During operation, the surface of the vacuum pump may exceed temperatures of 100°C. Risk of burns! Do not touch the hot surfaces of the vacuum pump. Please contact your local Busch representative if you have any doubts or questions Problem Possible Cause...
  • Page 10 Remove the drive motor and check the drive motor and the vacuum pump separately If the vacuum pump is jammed: Have the vacuum pump repaired (Busch ser- vice) The drive motor is defective Change the drive motor (Busch service)
  • Page 11 Partial clogging or blockage in suction or dis- Remove foreign particles charge lines Suction or discharge lines too long, or too Use larger diameter lines small (diameter) Troubleshooting Page 11...
  • Page 12: Exploded View

    Exploded view Exploded view Page 12...
  • Page 13: Spare Parts

    (on the name plate of the pump). This will allow Busch service Partnumber : 0994 000 018 technicians to check if the vacuum pump is compatible with a modified or improved part.
  • Page 14: Technical Data

    Technical data Technical data SV 1063 B SD 1063 B SV 1080 B SD 1080 B Nominal displacement 50 (60) Hz 63 (75) 80 (96) Ultimate pressure hPa (abs.) Overpressure hPa (abs.) 2000 2000 Nominal motor rating 50 (60) Hz...
  • Page 15: Ec Declaration Of Conformity

    NOTE: This Declaration of Conformity and the -mark affixed to the nameplate are valid for the vacuum pump within the Busch-scope of delivery. When this vacuum pump is integrated into a larger machinery the manufacturer of the larger machinery (this can be operator, too) must conduct the conformity assessment process for the larger machine, issue the Declaration of Conformity for it and affix the -mark.
  • Page 16: Busch - All Over The World In Industry

    Busch – All over the World in Industry www.busch-vacuum.com France Italy Singapore Argentine Busch Italia S.r.l. Busch France S.A.S. Busch Argentina S.R.L. Busch Vacuum Singapore Pte Ltd Via Ettore Majorana, 16 16, Rue du Bois Chaland Santo Domingo 3076 20 Shaw Road...

This manual is also suitable for:

Sd 1063 bSv 1080 bSd 1080 b

Table of Contents