Related Manuals for BUSCH SECO SV 1005 C
Summary of Contents for BUSCH SECO SV 1005 C
- Page 1 Installation and Operating Instructions Vacuum and Pressure Pumps SECO SV 1005 C / SD 1005 C / SV 1008 C / SD 1008 C 0870135648/-0001 21.10.2021 / Original instructions...
-
Page 2: Table Of Contents
Preface ....... 2 Congratulations on your purchase of the Busch vacuum and pressure Product Description . -
Page 3: Product Description
Conveying media with a lower or higher density than air leads to an in- creased thermal and/or mechanical load on the vacuum and pressure Safety pump and is permissible only after prior consultation with Busch. The gas shall be free from vapours that would condensate under the Intended Use temperature and pressure conditions inside the vacuum and pressure pump. -
Page 4: Noise Emission
However, VCI-products may attack the surfaces of plastics and elastomers. Seek advice from your local packaging dealer! Busch uses CORTEC VCI 126 R film for the overseas packaging of large equipment. SV 1005 C / SD 1005 C / SV 1008 C / SD 1008 C... -
Page 5: Suction Connection/Gas Inlet
In case the length of the discharge line exceeds 0.5 m it is prudent to use larger line sizes in order to avoid a loss of efficiency and an over- CAUTION load of the vacuum and pressure pump. Seek advice from your Busch representative! During operation the surface of the vacuum and pressure pump may reach temperatures of more than 70 °C. -
Page 6: Connecting Electrically
Version with three-phase motor: pump and is permissible only after prior consultation with Busch. ◆ Determine the intended direction of rotation with the arrow (f, The gas shall be free from vapours that would condensate under the... -
Page 7: Maintenance
In case an inlet air filter (62, 63) is installed: this manual shall be done by Busch service. ◆ Replace the inlet air filter (62, 63) In case an inlet screen is installed: ◆... -
Page 8: Removal From Service
“Declaration of Contamination” (form downloadable from www.busch-vacuum.com). Busch service will only accept vacuum and pressure pumps that come with a completely filled in and legally binding signed “Declaration of Contamination” (form downloadable from www.busch-vacuum.com). -
Page 9: Troubleshooting
Readjust the vacuum and pressure pump the cylinder is no longer adequate (Busch service) Internal parts are worn or damaged Repair the vacuum and pressure pump (Busch service) The gas conveyed by the vacuum and Process components evaporating under vac-... - Page 10 Try to turn the drive motor with the vacuum and pressure pump by hand If the vacuum and pressure pump is blocked: Repair the vacuum and pressure pump (Busch service) The drive motor is defective Replace the drive motor (Busch service)
- Page 11 Version with three-phase motor: lation and Commissioning The vacuum and pressure pump runs in the wrong direction Foreign objects in the vacuum and pressure Repair the vacuum and pressure pump (Busch pump service) Broken vanes (35) Stuck bearings The vacuum and pressure pump runs very...
-
Page 12: Exploded View
Exploded View Exploded View SV 1005 C / SD 1005 C / SV 1008 C / SD 1008 C page 12 0870135648... -
Page 13: Spare Parts/Accessories
0-9-414 7782 Fax: 0-9-414 7783 Find the list of Busch companies all over the world (by the time of the publication of these installation and operating instructions) on Ú page 16 (rear cover page). Find the up-to-date list of Busch companies and agencies all over the world on the internet at www.busch-vacuum.com. -
Page 14: Eu-Declaration Of Conformity
This Declaration of Conformity and the CE-mark affixed to the nameplate are valid for the machine within the Busch scope of delivery. This Declaration of Conformity is issued under the sole responsibility of the manufacturer. When this machine is integrated into a superordinate machinery the manufacturer of the superordinate machinery (this can be the operating company, too) must conduct the conformity assessment process for the superordinate machine or plant, issue the Declaration of Conformity for it and affix the CE-mark. -
Page 15: Uk Declaration Of Conformity
This Declaration of Conformity and the UKCA-mark affixed to the nameplate are valid for the machine within the Busch scope of delivery. This Declaration of Conformity is issued under the sole responsibility of the manufacturer. When this machine is integrated into a superordinate machinery the manufacturer of the superordinate machinery (this can be the operating company, too) must conduct the conformity assessment process for the superordinate machine or plant, issue the Declaration of Conformity for it and affix the UKCA-mark. -
Page 16: Technical Data
Technical Data For motor connection parameters see nameplate SV 1005 C SD 1005 C SV 1008 C SD 1008 C 50 Hz — — Nomical suction capacity m³/h 60 Hz — — 50 Hz — — Volume flow m³/h 60 Hz —... - Page 20 Busch Vacuum Solutions We shape vacuum for you. Argentina Denmark Malaysia South Africa info@busch.com.ar info@busch.dk busch@busch.com.my info@busch.co.za Australia Finland Mexico Spain sales@busch.com.au info@busch.fi info@busch.com.mx contacto@buschiberica.es Austria France Netherlands Sweden busch@busch.at busch@busch.fr info@busch.nl info@busch.se Bangladesh Germany New Zealand Switzerland sales@busch.com.bd info@busch.de sales@busch.co.nz...