Initial Setup Menu - Suzuki SMD7 Installation Manual

3. SETTINGS AND ADJUSTMENTS
Alphanumeric input
To enter alphanumeric characters, follow the procedure below.
Go back to the
previous screen/menu Cursor
Toggle between alphabet
keyboard and numeric keyboard
Cancel input and close the keyboard
1. Tap the character or numeral you want to input.
2. Repeat step 1 until you have input the required characters/numerals.
3. Tap [OK].
3.3

Initial Setup Menu

You can change the display language, setup the details for your vessel and other initial
settings, from the [Initial Setup] menu.
1. Tap the [Home] => [Settings] => [Initial Setup]. The [Initial Setup] menu appears.
2. Referring to the table below, set up the required menus.
Menu name Description
[Language] tab
[Language] Select the display language.
[Vessel] tab
[Vessel Type] Select the hull-type for your ves-
sel.
[Autopilot] tab
[NAVpilot Control] Select whether or not to use the
NAVpilot for navigation.
[Navigation Setup] tab
[Position Filter] When the DOP or receiving con-
dition is unfavorable, the GPS fix
may change, even if the vessel is
dead in water. This change can
be reduced by smoothing the raw
GPS fixes. The higher the setting,
the more smoothed the raw data,
however too high a setting slows
response time to change in lati-
tude and longitude. This is espe-
cially noticeable at high ship's
speeds.
Backspace
Capital/lower-case
toggle button
Confirm and apply
the characters
Cursor buttons
Spacebar
(moves the cursor)
Setting range/options
[English US], [English UK], others
[Power Displacement], [Power
Planing], [Sail Boat]
[ON], [OFF]
[Off], [Low], [Medium], [High]
20
Menu name Description
[Speed Filter] During position fixing, ship's ve-
locity (speed) is directly mea-
sured from the GPS satellite. The
raw velocity data may change
randomly depending on receiving
conditions and other factors. You
can reduce this random variation
by increasing the filter setting. If
the setting is too high, however,
the response to speed and course
change slows.
Map Datum Select the datum to use. For nor-
mal use, select [WGS 1984].
Perspective Angle Selects the point-of-view for 3D/
PS modes.
[Internal GPS Setup] tab
[SBAS Mode] Select whether or not to use
SBAS mode.
[Restart GPS] Restart reception of GPS satel-
lites.
[Dynamic Model] Set the operating environment.
Select [Automotive] for environ-
ments located 500 m or more
above sea level, or for high-speed
craft (capable of more than 45
kn). For all other environments,
use the default setting, [At Sea].
[Navigation Speed] The default setting is [Low]. Set to
[High] for more accurate and sta-
ble COG output. However, when
set to [High] and the ship speed is
below 0.1 m/s, COG output may
stop.
[Data Acquisition] tab
[GP330B SBAS Mode] Select whether or not to use the
connected GP-330B's SBAS
mode.
[WS200 SBAS Mode] Select whether or not to use the
connected WS-200's SBAS
mode.
[SC-30 Setup] tab
[SBAS Mode] Select whether or not to use the
connected FURUNO SC-30's
SBAS mode.
[Heading Offset] Apply an offset to the heading da-
ta.
[Pitch Offset] Apply an offset to the pitch data.
[Roll Offset] Apply an offset to the roll data.
[Manual Fuel Management] tab
[Manual Management] Select whether or not to manual
manage your fuel.
[Total Fuel Capacity] Set the total fuel capacity for your
vessel.
21
3. SETTINGS AND ADJUSTMENTS
Setting range/options
[Off], [Low], [Medium], [High]
[TOKYO], [WGS 1972], [WGS
1984]
[5°] to [60°]
[ON], [OFF]
-
[At Sea], [Automotive]
[Low], [High]
[ON], [OFF]
[ON], [OFF]
[ON], [OFF]
[-180°] to [180°]
[-90°] to [90°]
[-90°] to [90°]
[ON], [OFF]
[0] to [9999] (US gal)