Suzuki SMD7 Installation Manual page 30

APPENDIX 1 MENU TREE
1
Files Screenshots Screenshots (shows number of screenshots saved to internal memory)
Export to SD
Delete All Screenshots
User Data Export File Format (C-MAP, GPX, CSV)
Routes and
Points
Tracks
Settings
Export to SD
Backup
Restore from SD (select file to import)
Notifications Export to SD (CSV)
Log
Units Units Distance (NM, SM, km, NM+ft, NM+m, SM+ft)
Speed (kn, km/h, m/s, mph)
Wind Speed (kn, km/h, m/s, mph, Bft)
Depth (m, ft, fm, pb, HR)
Fish Size (cm, inch)
Temperature (°C, °F)
Air Pressure (hPa, mBar, mmHg, inchHg)
Oil/Boost Pressure (Bar, PSI, kPa)
Volume (l, US gal, UK gal)
Height/Length (m, ft)
Rate (l/h, US gal/h, UK gal/h)
Fuel
Formats and Bearing Display (M, T)
References
Magnetic Variation (Internal, External)
True Wind Calculation Reference (Ground, Surface)
Position Format (DD°MM.MMMM', DD°MM.MMM', DD°MM.MM',
Restore Restore Default Settings (Select Yes/No from pop up window)
Defaults
Initial Language (English US, English UK, others)
Setup Vessel Vessel Type (Power Displacement, Power Planing, Sail Boat)
Autopilot NAVpilot Control (ON, OFF)
Navigation Position Filter (Off, Low, Medium, High)
Setup Speed Filter (Off, Low, Medium, High)
Map Datum (WGS 1984, others)
Perspective Angle (5° to 60°, 30°)
Internal SBAS Mode (ON, OFF)
GPS Setup Restart GPS
Dynamic Model (At Sea, Automotive)
Navigation Speed (Low, High)
Data GP330B SBAS Mode (ON, OFF)
Acquisition WS200 SBAS Mode (ON, OFF)
SC-30 Setup SBAS Mode (ON, OFF)
Heading Offset (-180.0° to +180.0°, 0°)
Pitch Offset (-90.0° to +90.0°, 0°)
Roll Offset (-90.0° to +90.0°, 0°)
1 2
AP-6
Routes/Points (Shows number of routes/points
saved to internal memory)
Export to SD
Import from SD (select file to import)
Tracks/Track Points (Shows number of routes and
points saved to internal memory)
Export to SD
Import from SD (select file to import)
DD°MM'SS.ss", DD.DDDDDD)
1 2
Manual Fuel Manual Management (ON, OFF)
Management Total Fuel Capacity (0 to 9999 US gal)
NMEA Output Instance (0, 1, 2, 3, 4, 5)
IF NMEA Select IF (Select [IF-NMEAFI] to set the analog data that is input
Setup from the IF-NMEAFI.)
Category (Wind,ST800/ST850, Fuel, Fresh Water, Waste
Water, Live Weel, Oil, Black Water)
Resistance Full (0 ohm to 300 ohm; default: 33.50 ohm)
Resistance Mid (0 ohm to 300 ohm; default: 310.00 ohm)
Resistance Empty (0 ohm to 300 ohm; default: 240.00 ohm)
Capacity (0 to 2650 US gal)
Self Test (Starts a diagnotic test)
Refresh (Refresh the NMEA device list)
Rudder PORT/STBD Reversing (ON, OFF)
Setup
About System
Information
Fish Finder
Information
C-Weather Information
About OSS
Copyright
Service (For technicians only, requires password)
Restore Restore Default Settings (Select Yes/No from pop up window)
Defaults
Restore All to Factory Defaults (Select Yes/No from pop up window)
Clear Clear All Data and Settings (Select Yes/No from pop up window)
Memory
Engine
Diagnosis Instance (Tests selected engine)
Setup QR Code
Data Reset Reset Data (Select Yes/No from pop up
Installation Number of Engines (1,2,3,4)
Gateway Settings (Shows the settings of Gateway)
Station Setting (1st, 2nd, None)
Reset (Shows the settings of Gateway to reset)
AP-7
APPENDIX 1 MENU TREE
Software Version
Boot Version
Kernel Version
RootFS Version
C-MAP 4D LIB
Base Chart
Chart 2
Serial Number
Program Version
Boot Version
FPGA Version
FPGA Program Version
window)