Table of Contents
Advertisement
SuperServer 5019S-MN4 User's Manual
PCH SLOT4 PCI-E 3.0 X4 (IN X8) OPROM
Use this feature to select which firmware type to be loaded for the add-on card in this slot
for system boot. The options are Disabled, Legacy, and EFI.
PCH SLOT5 PCI-E 3.0 X8 OPROM
Use this feature to select which firmware type to be loaded for the add-on card in this slot
for system boot. The options are Disabled, Legacy, and EFI.
PCH SLOT6 PCI-E 3.0 X8 (IN X16) OPROM
Use this feature to select which firmware type to be loaded for the add-on card in this slot
for system boot. The options are Disabled, Legacy, and EFI.
Onboard LAN Option ROM Type
Select Enabled to enable Option ROM support to boot the computer using a network device
specified by the user. The options are Legacy and EFI.
Onboard LAN1 Option ROM
Use this option to select the type of device installed in LAN Port1 used for system boot. The
default setting for LAN1 Option ROM is PXE.
Onboard LAN2 Option ROM/Onboard LAN3 Option ROM/Onboard LAN4 Option ROM
(LAN3 Option ROM/Onboard LAN4 Option ROM: Available on the X11SSH-LN4F only)
Use this option to select the type of device installed in a LAN port specified by user for system
boot. The default setting for this item is Disabled.
Onboard Video Option ROM
Use this item to select the Onboard Video Option ROM type. The options are Disabled,
Legacy, and EFI.
VGA Priority
Use this item to select the graphics device to be used as the primary video display for system
boot. The options are Onboard and Offboard.
Network Stack
Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified Extensible
Firmware Interface) for network stack support. The options are Enabled and Disabled.
IPv4 PXE Support
Select Enabled to enable IPv4 PXE boot support. The options are Enabled and Disabled.
IPv6 PXE Support
Select Enabled to enable IPv6 PXE boot support. The options are Enabled and Disabled.
76
PXE boot wait time
Use this option to specify the wait time to press the ESC key to abort the PXE boot. Press
"+" or "-" on your keyboard to change the value. The default setting is 0.
Media detect count
Use this option to specify the number of times media will be checked. Press "+" or "-" on your
keyboard to change the value. The default setting is 1.
Super IO Configuration
The following Super IO information will display:
•
AMI SIO Driver Version
Super IO Chip Logical Device(s) Configuration
Serial Port 1
Serial Port 1 Configuration
This submenu allows the user the configure settings of Serial Port 1.
Serial Port 1
Select Enabled to enable the selected onboard serial port. The options are Enabled and
Disabled.
Logical Device Settings
This item displays the current status of a serial part specified by the user.
Serial Port 1 Change Settings
This feature specifies the base I/O port address and the Interrupt Request address of a
serial port specified by the user. Select Auto to allow the BIOS to automatically assign the
base I/O and IRQ address.
The options for Serial Port 1 are Use Automatic Settings, (IO=3F8h; IRQ=4; DMA), (IO=3F8h;
IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA), (IO=2F8h; IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA), (IO=3E8h;
IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA), and (IO=2E8h; IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA).
Serial Port 2
Serial Port 2 Configuration
This submenu allows the user the configure settings of Serial Port 2.
Serial Port 2
Select Enabled to enable the selected onboard serial port. The options are Enabled and
Disabled.
77
Chapter 6: BIOS
Advertisement
Table of Contents
