Troubleshooting Guide; Limited Warranty - Team Losi 22S Maxxis Manual

EN
DYNAMITE TAZER SPORT 3300KV BRUSHLESS MOTOR (DYNS1495)
®
PRECAUTIONS
Never touch moving parts.
Never disassemble while the batteries are installed.
Always let parts cool before touching.
GEARING
The vehicle is equipped with optimal gearing for 3S batteries. When using 2S batteries,
changing the pinion gear to a 23T 48P pinion will optimize speed, power and efficiency.
Installing a pinion gear with fewer teeth or a spur gear with more teeth will increase torque
Frank wants to change second sentence to: When using 2S batteries, the 22S
and reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with fewer teeth
will work perfectly on the stock gearing. However, for 2S running, changing
will reduce torque and increase top speed. Take care when installing larger pinion gears as
the pinion gear to a 23T 48P pinion will optimize speed, power and efficiency.
this can "overgear" the vehicle, resulting in an overheated motor and ESC. When testing dif-
ferent gearing options, pay close attention to the temperature of the motor and speed control
to ensure you are operating within the correct temperature range. Neither the motor nor the
This doesn't make sense. The 2S needs to change pinion gear? or it will work
ESC should be hot to the touch. If the motor is too hot, switch to a lower pinion gear and/or
ok with stock gears?
higher spur gear combination.
CHANGING THE PINION GEAR/GEAR RATIO
1. Remove the screws holding the gear cover in
2. Loosen the set screw and remove the installed pinion gear.
3. Loosen the motor screws and slide the motor back.
4. Place the new pinion on the end of the motor shaft so the set screw is located
over the flat on the shaft.
5. Position it so the teeth line up with the spur gear and secure the pinion by tightening
the set screw.
6. Set the gear mesh.

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE
Battery not charged or plugged in
Vehicle does not operate ESC switch not "ON"
Transmitter not "ON" or low battery
Pinion not meshing with spur gear
Pinion spinning on motor shaft
Motor runs but wheels
do not rotate
Transmission gears stripped
Drive pin broken
Servo plug not in receiver properly
Steering does not work
Servo gears or motor damaged
Will not turn one direction Servo gears damaged
Motor wire solder joint is damaged
Motor does not run Motor wire broken
ESC damaged
Motor over-geared
ESC gets hot
Driveline bound up
Battery pack not fully charged
Poor run time and/or sluggish
Charger not allowing full charge
acceleration
Driveline bound up
Transmitter batteries low
Poor range and/or glitching Vehicle battery low
Loose plugs or wires

LIMITED WARRANTY

What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the
"Product") will be free from defects in materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due
to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use,
installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv)
attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product
not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable
technical regulations or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY
OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
8
place.
SOLUTION
Charge battery/plug in
Turn on ESC switch
Turn on/replace batteries
Adjust pinion/spur mesh
Tighten pinion gear setscrew on motor shaft flat spot
Replace transmission gears
Check and replace drive pin
Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity
Replace or repair servo
Replace or repair servo
Resolder the motor wire with the proper equipment
Repair or replace as needed
Contact Horizon Hobby Product Support
Use smaller pinion or larger spur gear
Check wheels and transmission for binding
Recharge battery
Try another charger
Check wheels, transmission for binding
Check and replace
Recharge battery
Check all wire connections and plugs
SETTING THE GEAR MESH
The gear mesh has already been set at the factory. Setting it is only necessary when changing
motors or gears.
Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle. When
the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If
the mesh is too tight, speed could be limited and the motor and ESC will overheat.
1. Loosen the motor screws and slide the motor back.
2. Put a small piece of paper between the pinion and spur gears.
3. Push the gears together while tightening the motor screws.
4. Remove the paper. Check the mesh at 3–5 different locations around
the spur gear for a small amount of movement.
5. Install gear cover.
NOTICE: For a 3S Li-Po battery, use the included 18T pinion gear. For a 2S Li-Po battery,
we recommend installing the optional 23T pinion gear (LOS4123).
NOTICE: If you use the 23T pinion gear with a 3S Li-Po battery, damage to the vehicle, ESC,
and/or motor will occur.
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER'S INTENDED USE.
Purchaser's Remedy
Horizon's sole obligation and purchaser's sole and exclusive remedy shall be that Horizon
will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be
defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty
claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase
is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY.