Appendix A Outline Of Format; A-1. Outline; A-2. Recording Format - Sony DNW-A100 Maintenance Manual

This section describes the recording format, heads configu-
ration and signal processing.

A-1. Outline

Sony DNWseries are 1/2-inch component digital VTRs
using a new "Betacam SX" format. This unit is a Digital
Video Hybrid Recorder in which the "Betacam SX" VTR
and hard disk were integrated. Incorporation of hard disk
into the VTR enables a nonlinear video/audio edit function.
In the Betacam SX format, "MPEG2 4:2:2 Profile @Main
Level" is used as a compression system.
Interframe compression technology is first used as VTR
format. The data rate is compressed to approximately 1/10
by this technology. The compressed data is then recorded
on tape (Note1 .
By compressing of the data late, the S cassette makes
continuous recording of 60 minutes possible, and the L
cassette makes continuous recording of 184 minutes
possible.
Moreover, the data can be recorded on not only the cassette
for the Betacam SX but also the metal particle tape for the
conventional Betacam SP by Betacam SX format.
This unit enables the high-reliability playback without
using a high-precision tracking by the head configuration
based on Multiple Tracing technology.
In the DNW-A100/A100P, the data can be transferred at
four times the normal speed by application of the Multiple
Tracing technology.
In this unit, the analog tape (oxide and metal particle)
recorded based on the Betacam/Betacam SP format can
also be played back. Therefore, current analog Betacam
recorded tapes can also be used directly.
Note 1: The audio data is recorded by non-compression.
Multiple Tracing Technology
In the Multiple Tracing technology, the non-tracking technol-
ogy used for a digital audio tape recorder is applied for VTR.
This technology requires no high-precision tracking during
recording as well as playback.
For the playback at variable speed, it was necessary changing
the drum rotation relative the tape speed or using the dynam-
ic tracking (DT) heads for precision tracking in the past.
DNW-A100/A50P/A45
DNW-A100P/A50P/A45P
Appendix A
Outline of Format
In this multiple tracking technology, two playback heads
are provided for one recorded track. If one playback head
missed the recorded track, the another playback head
makes up the complete playback signal.
This technology enables the variable-speed (JOG) playback
(_1 to +1 times the normal speed) without using the
conventional dynamic tracking (DT) head. Moreover, by
increasing the number of playback heads, it can transfer
data from the tape to the signal processing circuit at high
speed without changing the drum rotation changing only
the tape speed.
Note2: DNW-A100/A100P is equipped with this
function.

A-2. Recording Format

Foot Print
Fig. A-2-1 shows the foot print in the 525/60 system (the
top of figure) and the 625/50 system (the bottom of figure) .
This figure shows the tape pattern of a Betacam SX at
right, and the foot print of a Betacam SP at left,
respectively.
Foot Print of Helical Track
In the Betacam SX format, two-frame (1 GOP*) video
data, system data and four-channel audio data is recorded
on ten (525/60 system) or twelve (625/50 system) helical
tracks.
*GOP: Group of Picture
This unit records two helical tracks in pairs. Therefore, the
drum rotation is approximately 75 per second (common in
525/60 and 625/50 systems).
In the playback of the Betacam/Betacam SP format, the
number of drum rotations is approximately 30 per second
(525/60) or 25 per second (625/50) .
Moreover, the tape speed of the Betacam SX format is
lower than that of the Betacam/Betacam SP format by
approximately half.
This unit detects whether the tape to be played back is
based on the Betacam SX format or Betacam/Betacam SP
format by the initial signal of playback, and as a result, the
tape is played back by the proper drum rotation and tape
speed.
(Note 2
A-1