Download Print this page
WaterLogic WL380 Troubleshooting
Hide thumbs Also See for WL380:

Advertisement

Quick Links

1. Red Power Switch and Green Heater & Compressor Switch won't light
2. Red Power Switch and Green Heater & Compressor Switch is lit but the Status LED lights
on the Front are not lit
3. Compressor Runs but does Not Chill
4. Compressor is Not Running
 
 
1. Red Power Switch and Green Heater & Compressor  
Switch won't light 
 
 
Possible Reason 
Circuit Breaker 
Fuse is Blown 
Defective / Loose Power Cord 
Failed Socket ‐ Power Line 
Noise Filter, Electro‐Magnetic 
Interference filter (EMI) 
Defective Red Power Switch  
Defective Green Heater & 
Compressor Switch 
 
 
WL380 Manual 
POWER TROUBLESHOOTING INDEX 
Check the Circuit Breaker 
Replace Fuse.  Use 15‐amp Waterlogic Fuse 
 
Check that Power Cord is properly plugged in.  If it is properly 
plugged in, use a different power cord to verify.  Use only 
Waterlogic supplied power cord. 
 
Replace Socket ‐ Power Line Noise Filter, Electro‐Magnetic 
Interference filter (EMI) 
Replace Red Power Switch 
Replace Green Heater & Compressor Switch  
 
                                                                 Page 39 ‐ Revision:  2‐5‐2018 
Solution 

Advertisement

loading
Need help?

Need help?

Do you have a question about the WL380 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for WaterLogic WL380

  • Page 1 3. Compressor Runs but does Not Chill 4. Compressor is Not Running     1. Red Power Switch and Green Heater & Compressor   Switch won’t light      Possible Reason  Solution  Circuit Breaker  Check the Circuit Breaker  Fuse is Blown  Replace Fuse.  Use 15‐amp Waterlogic Fuse    Check that Power Cord is properly plugged in.  If it is properly  Defective / Loose Power Cord  plugged in, use a different power cord to verify.  Use only  Waterlogic supplied power cord.    Failed Socket ‐ Power Line  Replace Socket ‐ Power Line Noise Filter, Electro‐Magnetic  Noise Filter, Electro‐Magnetic  Interference filter (EMI)  Interference filter (EMI)  Defective Red Power Switch   Replace Red Power Switch  Defective Green Heater &  Replace Green Heater & Compressor Switch   Compressor Switch        WL380 Manual                                                                   Page 39 ‐ Revision:  2‐5‐2018 ...
  • Page 2 Possible Reason  Solution  Bad Transformer  Replace Transformer  Black Power Connector to the  Properly connect.  PCB is not properly connected  Bad Front PCB   Replace Front PCB  Defective Green Heater &  Replace Green Heater & Compressor Switch  Compressor Switch    3. Compressor Runs but Does Not Chill      Possible Reason  Solution  Condenser is dirty  Clean the condensing coil of any obstructions or dust.    Make sure unit is not under minimum ventilation requirements  Reduction of airflow into unit.  (2 to 4 inches of clearance around the unit for heat exchange).      Low or lost refrigerant.    Compressor is running very    hot (over 150 F)  Refrigerant recharge as necessary.  See Specifications for  refrigerant charge data.          WL380 Manual                                                                   Page 40 ‐ Revision:  2‐5‐2018 ...
  • Page 3 Red Power and Green Heater  Turn Green Heater & Compressor Switch on.    & Compressor Switch in the   I = ON  O = OFF position          Isolate Power and remove red leads from cold thermostat to check  Cold Thermostat is Faulty   continuity.  Thermostat should be closed if sensor is at room  temperature.  Check for continuity.  Replace thermostat        Turn Green Heater & Compressor Switch off.  O = OFF.    Remove the compressor cap on side of the compressor;      Disconnect the black and red terminal connectors;     Compressor Starting Circuit   Inspect the starter and overload relay for any defects.    Faulty or Over Heated    (tripped)  Check with Multi‐Meter to ensure 120V AC is being supplied to the  compressor starter.  Turn ON Red Power and Green Heater &  Compressor Switch with meter hooked to red and black  compressor leads.    Replace components(s) as needed.            WL380 Manual                                                                   Page 41 ‐ Revision:  2‐5‐2018 ...