Emulex LP11000 Installation Manual
Host bus adapter
Hide thumbs
Also See for LP11000:
- Firmware update manual (5 pages) ,
- Troubleshooting and maintenance manual (23 pages) ,
- User manual (69 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Emulex LP11000
Summary of Contents for Emulex LP11000
- Page 1 LP11000 HBA Installation Manual...
- Page 2 Emulex Corporation for its use; or for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Emulex Corporation.
-
Page 3: Table Of Contents
Applying Power ... 6 Viewing the LEDs ...6 POST Conditions and Results ...6 References ... 7 Specifications ... 7 FCC and Regulatory Notices ... 8 Declaration of Conformity ... 9 Laser Safety Notice ...11 LP11000 Hardware Installation Manual Page iii... -
Page 4: Introduction
LP11000 host bus adapter (HBA) is a single-channel, 4-gigabit per second (Gb/s), Fibre ® Channel (FC) PCI-X 2.0 HBA. The core technology of this HBA is Emulex’s seventh generation FC controller. The controller incorporates a multi-function native PCI-X 2.0 core that is compliant to the Peripheral Component Interconnect (PCI) and PCI-X local bus specifications. -
Page 5: Compatibility
PCI-X Mode 2 64-bit data and 266-MHz (133-MHz clock frequency, double data rate) • 3.3-V and 5-V PCI power required for operation LP11000 Hardware Installation Manual Windows 2000 Server, Windows Server 2003, Novell NetWare, Sun Solaris, Linux and HP-UX PCI and PCI-X Mode 1 and 2 compliant systems... -
Page 6: Setting The Jumpers
Setting the Jumpers Caution: Emulex LightPulse® HBAs contain electronic components that can be damaged by static electricity through an electrostatic discharge (ESD) event. To prevent ESD damage, maintain constant contact with any grounded metal surface. A grounding wrist strap is useful for this purpose. -
Page 7: Installing The Host Bus Adapter
World Wide Name (WWN) derived from the IEEE address, and this number is needed for FC connectivity. The IEEE address is used when configuring your system. The serial number is used when communicating with Emulex. All numbers are clearly marked on the board. We recommend that you record these numbers before installation. -
Page 8: Attaching Media
Figure 3: Connecting Fiber Optic Cable 2. Connect the other end of the cable to the Fibre Channel device. After the media is connected to the HBA, you are ready to apply power to the computer. LP11000 Hardware Installation Manual Minimum Length Connector .5 meters... -
Page 9: Applying Power
3 Blinks Slow Blink Slow Blink Slow Blink Fast Blink Slow Blink Flashing Slow Blink LP11000 Hardware Installation Manual Green LED Wake-up failure (Dead board) POST failure (Dead board) Wake-up failure monitor POST failure POST processing in progress Failure while functioning... -
Page 10: References
References Specifications Table 5: LP11000 Specifications Parameter Media Interface The controller interfaces to the physical media through an FC-0 Media Interface (FC-PI compliant transceiver), and then connects through dual optical fiber LC connectors. Physical Dimensions Low-profile MD2 form factor, 6.600 inches by 2.536 inches, and accommodates both the full-height and low-profile bracket. -
Page 11: Fcc And Regulatory Notices
The reader is cautioned that changes or modifications made to the equipment not expressly approved by Emulex could void the user's authority to operate this equipment. The above statement applies to products marketed in the USA. -
Page 12: Declaration Of Conformity
WARNING: This is a class A product. In a domestic environment, this product may cause radio interference requiring the user to take adequate measures. Note: Changes or modifications not expressly approved by Emulex Corporation could void the user's authority to operate this equipment. - Page 13 LP11000 Hardware Installation Manual Page 10...
-
Page 14: Laser Safety Notice
Certification and Classification The LP11000, LP11002 and LP1150 host adapters may contain a laser product known as a small form factor transceiver. This transceiver provides the physical connection to the optical cable, and its LC-style connector extends through the mounting bracket. - Page 15 Short wavelength and long wavelength small form factor transceivers embedded in Emulex host adapter are non-OFC. For non- OFC links, a compatible laser device must be non-OFC and certified as a Class 1 laser product.
- Page 16 Copies of the certificate of conformity for any small form factor transceiver sold by Emulex can be obtained upon request from Emulex Corporation, Costa Mesa. LP11000 Hardware Installation Manual Page 13...
Need help?
Do you have a question about the LP11000 and is the answer not in the manual?
Questions and answers