Summary of Contents for Camille Bauer SIRAX BT5300
Page 1
П б SIRAX BT5300 Архангельск (8182)63-90-72 Калининград (4012)72-03-81 Новосибирск (383)227-86-73 Сочи (862)225-72-31 Астана (7172)727-132 Калуга (4842)92-23-67 Омск (3812)21-46-40 Ставрополь (8652)20-65-13 Астрахань (8512)99-46-04 Кемерово (3842)65-04-62 Орел (4862)44-53-42 Сургут (3462)77-98-35 Барнаул (3852)73-04-60 Киров (8332)68-02-04 Оренбург (3532)37-68-04 Тверь (4822)63-31-35 Белгород (4722)40-23-64 Краснодар (861)203-40-90 Пенза...
Page 2
The content of this document has been reviewed to ensure correctness. Nevertheless it may contain errors or inconsistencies and we cannot guarantee completeness and correctness. This is especially true for different language versions of this document. This document is regularly reviewed and updated. PM 1000290 000 00 Device handbook SIRAX BT5300 2/31...
1. Introduction 1.1 Purpose of this document This document describes the universal measurement device SIRAX BT5300. It is intended to be used by: Installation personnel and commissioning engineers • Service and maintenance personnel • Planners • Scope This handbook is valid for all hardware versions of the BT5300. Some of the functions described in this document are available only, if the neces- sary optional components are included in the device.
3. Device overview The SIRAX BT5300 is a top-hat rail mounted Transducer and used to measure and convert frequency input into an proportional DC current or voltage output signal. Input frequency and Output Voltage/Current is displayed on LCD and indicated by LED’s.
A marked and easily accessible current limiting switch has to be arranged in the vicinity of the device for turning off the power supply. Fusing should be 10 Amps or less and must be rated for the available voltage and fault current. PM 1000290 000 00 Device handbook SIRAX BT5300 6/31...
Before commissioning you have to check if the connection data of the device match the data of the plant. If so, you can start to put the device into operation by switching on the power supply and the measurement inputs. Label version PM 1000290 000 00 Device handbook SIRAX BT5300 7/31...
6.1 Operating the device O/P1 O/P2 SIRAX BT5300 can be confi gured and programmed at site for the following: Input parameters (i.e start, end and elbow value of Input) and Output parameters(i.e as INPUT x012 Voltage or as Current and start, end and elbow value of outputs).
3) Programming via optional RS485 (Modbus) communication port. 7.1 Programming via Front LCD & Two keys The following sections comprise step by step procedures for confi guring the SIRAX BT5300 for individual user requirements. To access the set-UP screens, press and hold the “...
Down” key will scroll the value of the third digit from 0 through to 9, the value will wrap from 9 round to 0. Pressing the “ Up” key will advance the operation to the next digit and set the third digit, in this case to “4” PM 1000290 000 00 Device handbook SIRAX BT5300 10/31...
Page 11
Pressing the “ Down” key will re-enter to the “New/Change Password” entry stage. Pressing the “ Up” key will confi rm New Password and advance to the Communication parameter selecti- on (section 7.1.2). PM 1000290 000 00 Device handbook SIRAX BT5300 11/31...
Down” key will re-enter to the “New / Change Address value edit” mode. Pressing the “ Up” key will confi rm New Address value and advance to Baud Rate selection (section 7.1.2.2). PM 1000290 000 00 Device handbook SIRAX BT5300 12/31...
Down” key will be re-enter into Parity Edit mode. Pressing the “ Up” key will set the present condition as parity and advance to the Input parameter selecti- on (section 7.1.3). PM 1000290 000 00 Device handbook SIRAX BT5300 13/31...
Down” key will re-enter into Output 2 Edit mode. Pressing the “ Up” key accepts the present type for Output 2 and advance to the Input parameter selecti- on (section 7.1.4). O/P 2 PM 1000290 000 00 Device handbook SIRAX BT5300 14/31...
INPUT x012 INPUT Pressing the “ Up” key will confi rm New End value of Input and advance to the Start value of Input selecti- on (section 7.1.4.2). O/P 12 y012 PM 1000290 000 00 Device handbook SIRAX BT5300 15/31...
Down” key will re-enter to the “New / Change Start value of Input edit” mode. INPUT x012 INPUT Pressing the “ Up” key will confi rm New Start value of Input and advance to the Elbow function selection (section 7.1.4.3). O/P 12 y012 PM 1000290 000 00 Device handbook SIRAX BT5300 16/31...
Page 17
9 round to 0 depending on the set End value of Input. O/P 12 y012 Pressing the “ Up” key will advance the operation to the next digit and set the second digit, in this case to “5”. PM 1000290 000 00 Device handbook SIRAX BT5300 17/31...
9 round to 0, if fi rst digit is set to 1. O/P 1 Pressing the “ Up” key will advance the operation to the next digit and set the second digit, in this case to “8”. PM 1000290 000 00 Device handbook SIRAX BT5300 18/31...
4 round to 0 depending on the set End value of Output. O/P 1 Pressing the “ Up” key will advance the operation to the next digit and set the second digit, in this case to “0”. PM 1000290 000 00 Device handbook SIRAX BT5300 19/31...
2 round to 0 depending on the set End value of Output. O/P 1 Pressing the “ Up” key will advance the operation to the next digit and set the fi rst digit, in this case to “1”. PM 1000290 000 00 Device handbook SIRAX BT5300 20/31...
Down” key will enter the “New/Change End value of the Output 2 edit” mode. Pressing “ Up” key will set the present value as End value of the Output 2 and advance to the Start value of Output selection (section 7.1.5.2.2). O/P 2 PM 1000290 000 00 Device handbook SIRAX BT5300 21/31...
Page 22
Down” key will re-enter to the “New / Change End value of the Output 2”. O/P 2 Pressing the “ Up” key will confi rm New End value of the Output 2 and advance to the Start value of Output selection (section 7.1.5.2.2). PM 1000290 000 00 Device handbook SIRAX BT5300 22/31...
Page 23
Pressing the “ Up” key will confi rm New Start value of the Output 2 and advance to the Elbow value of O/P 2 Output selection (section 7.1.6.2.3) or exit setup menu. PM 1000290 000 00 Device handbook SIRAX BT5300 23/31...
Page 24
Down” key will re-enter to the “New / Change Elbow value of the Output 2”. Pressing the “ Up” key will confi rm New Elbow value of the Output 2 and exit setup menu. O/P 2 PM 1000290 000 00 Device handbook SIRAX BT5300 24/31...
Chapter 11. Schritt 2: Programming Program SIRAX BT5300 via the Modbus RTU interface and the CB-Configurator software. Please observe the detailed Modbus description in Chapter 11. To change the output from current to voltage, enter the value “1”.
Incorrect disposal can cause environ- mental risks. 8.5 Return All devices delivered to Camille Bauer Metrawatt AG shall be free of any hazardous contaminants (acids, lyes, solutions, etc.). Use original packaging or suitable transport packaging to return the device. Damage by returning Damages caused by improper returning, no warranties or guarantees can be given.
Output end Value Y2 (Voltage or Current) Basic Accuracy: 0.2*C Factor C (The Highest value applies): Linear characteristics: Bent characteristics: Y1 – Y0 1– · or C=1 X1 – X0 or C=1 1– 1– or C=1 1– PM 1000290 000 00 Device handbook SIRAX BT5300 27/31...
Page 28
Protection Class: II (Protection Isolated acc. to EN 61010-1, EN 61010-2-030) Protection: IP 40, housing acording to EN 60529 IP 20,terminal according to EN 60529 Pollution degree: Installation Category: III, 300V PM 1000290 000 00 Device handbook SIRAX BT5300 28/31...
10, in each of the three axes EN 60068-2-7: Shock Acceleration: 3 x 50g 3 shocks in each direction EN 60068-2-1/-2/-3 Cold, Dry, Damp heat EN 61000-4-2/-3/-4/-5/-6 EN 55011 Electromagnetic compatibility 12. Dimensional drawings 43,5mm 106,5mm PM 1000290 000 00 Device handbook SIRAX BT5300 29/31...
11. Interface Defi nition Modbus RTU SIRAX BT5300 supports Modbus RTU protocol (RS485). The permissible address range for the BT5300 is between 1 and 247. Broadcast Mode (address 0) is not allowed. The maximum latency time of an BT5300 is 200ms i.e. this is the amount of time that can pass before the fi rst response character is output.
– – 40035 Analog O/P 2 This address is used to set the Analog O/P2 as Voltage/Current. Voltage = 1 Current = 2 40037 – – – 40039 – – – PM 1000290 000 00 Device handbook SIRAX BT5300 31/31...
Page 32
По вопросам продажи и поддержки обращайтесь: Архангельск (8182)63-90-72 Калининград (4012)72-03-81 Новосибирск (383)227-86-73 Сочи (862)225-72-31 Астана (7172)727-132 Калуга (4842)92-23-67 Омск (3812)21-46-40 Ставрополь (8652)20-65-13 Астрахань (8512)99-46-04 Кемерово (3842)65-04-62 Орел (4862)44-53-42 Сургут (3462)77-98-35 Барнаул (3852)73-04-60 Киров (8332)68-02-04 Оренбург (3532)37-68-04 Тверь (4822)63-31-35 Белгород (4722)40-23-64 Краснодар...