Leica BLK2GO User Manual
Hide thumbs Also See for BLK2GO:

Advertisement

Leica BLK2GO
User Manual
Version 1.0
English

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BLK2GO and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Leica BLK2GO

  • Page 1 Leica BLK2GO User Manual Version 1.0 English...
  • Page 2 Leica Geosystems authorised service centre. Trademarks Trademarks are the property of their respective owners. Leica Geosystems On the last page of this manual, you can find the address of Leica Geosystems address book headquarters. For a list of regional contacts, please visit http://leica-geosystems.com/contact-us/sales_support.
  • Page 3: Table Of Contents

    Table of Contents Safety Directions General Introduction Definition of Use Limits of Use Responsibilities Hazards of Use Laser Classification 1.6.1 General 1.6.2 Scanning Laser Electromagnetic Compatibility (EMC) FCC Statement, Applicable in U.S. IC Statement, Applicable in Canada Description of the System System Components Container Contents Instrument Components...
  • Page 4 Software Licence Agreement Table of Contents...
  • Page 5: Safety Directions

    Safety Directions General Introduction Description The following directions enable the person responsible for the product, and the person who actually uses the equipment, to anticipate and avoid opera- tional hazards. The person responsible for the product must ensure that all users understand these directions and adhere to them.
  • Page 6: Definition Of Use

    Suitable for use in dry environments only and not under adverse conditions. Responsibilities Manufacturer of the Leica Geosystems AG, CH-9435 Heerbrugg, hereinafter referred to as product Leica Geosystems, is responsible for supplying the product, including the User Manual and original accessories, in a safe condition. Safety Directions...
  • Page 7: Hazards Of Use

    To be familiar with local regulations relating to safety and accident pre- • vention. To inform Leica Geosystems immediately if the product and the applica- • tion becomes unsafe. To ensure that the national laws, regulations and conditions for the oper- •...
  • Page 8 NOTICE Removal of battery during operation or shutdown This can result in a file system error and data loss! 1942_002 Precautions: ▶ Do NOT remove the battery during operation of the instrument, or during the shutdown procedure. ▶ Always switch off the instrument by pressing the On/Off key, and wait until the instrument has shutdown completely before removing the bat- tery.
  • Page 9 Dispose of the product appropriately in accordance with the national regulations in force in your country. Always prevent access to the product by unauthorised personnel. Product-specific treatment and waste management information can be received from your Leica Geosystems distributor. Safety Directions...
  • Page 10: Laser Classification

    Improperly repaired equipment Risk of injuries to users and equipment destruction due to lack of repair knowledge. Precautions: ▶ Only authorised Leica Geosystems Service Centres are entitled to repair these products. For the AC/DC power supply: WARNING Unauthorised opening of the product...
  • Page 11: Scanning Laser

    Base rotation 2.5 Hz Labelling 90° 0° 360° 0° 270° Complies with 21 CFR Model: BLK2GO 1040.10 and 1040.11 Art.No.: 875578 except for conformance Leica Geosystems AG with IEC 60825-1 Ed.3, CH-9435 Heerbrugg as described in Laser Made in Switzerland Notice No.
  • Page 12 Although the product meets the strict regulations and standards which are in force in this respect, Leica Geosystems cannot completely exclude the possib- ility that function of the product may be disturbed in such an electromagnetic environment.
  • Page 13: Fcc Statement, Applicable In U

    Precautions: ▶ Although the product meets the strict regulations and standards which are in force in this respect, Leica Geosystems cannot completely exclude the possibility that other equipment can be disturbed or that humans or animals can be affected. ▶...
  • Page 14 (2) this device must accept any interference received, Including interference that may cause undesired operations. 19551_001 Labelling GEB821 100°C Manufactured by Huizhou Longji Electronics Co.,Ltd. for Leica Geosystems AG 2INR19/66 L.No.:XXXXX Model/型號:GEB821 Art.No.:879638 Leica Geosystems AG Li-Ion Battery 型號二次鋰離子電池組 CH-9435 Heerbrugg 額定值...
  • Page 15: Ic Statement, Applicable In Canada

    IC Statement, Applicable in Canada WARNING This Class (B) digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe (B) est conforme à la norme NMB-003 du Canada. Canada Compliance Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence- exempt RSS(s).
  • Page 16: Description Of The System

    Description of the System System Components System components BLK2GO with table stand Lithium-Ion battery GEB821 (3x) AC power cable AC power adapter Battery charger GKL821 Transport case 19492_001 Container Contents Container contents Battery charger GKL821 AC power adapter and AC power cable...
  • Page 17: Instrument Components

    Instrument Components Instrument components 19557_001 Dome Air outlet Ring-shaped LED Power button Detail camera Air inlet Panoramic camera Battery compartment Handle Locking mechanism for bat- Mounting for accessories tery cover Description of the System...
  • Page 18: User Interface

    < 2 sec. continuous green. tialising and the LED starts blinking yellow. Press and hold the in recording mode. The BLK2GO is taking a button < 2 sec. picture with the detail camera. Press and hold the in recording mode.
  • Page 19: Instrument Status

    Instrument Status Instrument status The ring-shaped LED lights up in different colours and lighting intervals to show the operation states of the BLK2GO. 19558_002 Description Details Colours Green • Yellow • • Lighting intervals Continuous • Blinking • Pulsating •...
  • Page 20 The BLK2GO is running a firmware update. continous The firmware update was success- ful. The BLK2GO is in idle state. continous The firmware update failed. Press and hold the button for < 2 sec to bring the BLK2GO to the idle state. User Interface...
  • Page 21: Power Supply

    For Li-Ion batteries, a single discharging and charging cycle is sufficient. • We recommend carrying out the process when the battery capacity indic- ated on the charger or on a Leica Geosystems product deviates signific- antly from the actual battery capacity available. Operation/ The batteries can be operated from −20 °C to +55 °C/−4 °F to +131 °F.
  • Page 22 Charger components DC input Battery bay with char- ging function Battery status LED Battery connector 19535_001 LED indicators 19536_001 LED indicator Status Description No activity. Solid green The battery is fully charged. Blinking orange The battery is charging. Solid red Failure.
  • Page 23: Battery

    Remove and insert the battery again. Make sure that the battery is correctly positioned in the battery bay. Disconnect from AC power and reconnect. If the failure persists or reappears from time to time, the charger must be sent to a Leica Geosystems authorised service centre. Battery NOTICE Always shut down the instrument before removing the battery.
  • Page 24 Remove and insert Remove the battery the battery step-by-step 19544_001 Slide the locking mechanism of the battery to the open position. Lift the battery and remove it from the compartment. Insert the battery 19545_001 Attach the upper side of the battery to the compartment at an angle and then lower the bottom side.
  • Page 25 Battery status Press the status button to check the battery status. 19546_001 Status LED Battery status 0%-30% 19547_001 31%-60% 19548_001 61%-90% 19549_001 91%-100% 19550_001 Charge batteries The GKL821 can charge one to four batteries at a time. All batteries ☞ step-by-step are charging in parallel.
  • Page 26 Insert the battery with the contact slots facing downwards. The LED of the battery bay blinks orange indicating the charge process. Refer to "LED indicators". If the LED of the battery bay lights solid green the battery is fully charged. Disconnect the charger plug from the DC input of the charger.
  • Page 27: Operation

    Follow the instructions on the app to establish the connection. Place the BLK2GO on the table stand and press the power button to start the scan. The ring-shaped LED is blinking yellow and the instrument is initialising.
  • Page 28: Imaging

    Connecting to a Start the BLK2GO and wait until the LED is continuous green. computing device On the computing device, in the Connection screen, select the con- step-by-step nection mode and follow the instructions. Imaging Description The BLK2GO can collect two different types of images: A panoramic image using 3 calibrated panoramic cameras.
  • Page 29: Troubleshooting

    If status does not change or the problem occurs again, contact the Leica support. Troubleshooting - If you experience problems with your instrument, check the BLK2GO web page support contacts at https://www.blk2go.com/ for support information and contacts. Operation...
  • Page 30: Field Of View (Fov)

    19576_002 Cooling System Description The BLK2GO has an air cooling system. It sucks in and circulates air to main- tain the temperature of the system components. The air inlet and the filter cartridge protect from dust particles entering the housing and components.
  • Page 31 The BLK2GO is not supposed to work in a dusty environment, since ☞ the laser measurements suffer a lot from dust refraction. Refer to "Ambient Conditions". Operation...
  • Page 32: Care And Transport

    Shipping When transporting the product by rail, air or sea, always use the complete ori- ginal Leica Geosystems packaging, container and cardboard box, or its equival- ent, to protect against shock and vibration. Shipping, transport of When transporting or shipping batteries, the person responsible for the...
  • Page 33: Cleaning And Drying

    Cleaning and Drying Damp products Dry the product, the transport case, the foam inserts and the accessories at a temperature not higher than 40°C /104°F and clean them. Remove the battery cover and dry the battery compartment. Do not repack until everything is completely dry.
  • Page 34: Filter Cleaning Procedure

    Clean or replace the filter cartridge • The ring-shaped LED indicates reaching high temperature of the BLK2GO. If this indication occurs after few minutes of operation in standard working con- ditions, it can be necessary to clean the air inlet and clean or replace the filter cartridge.
  • Page 35 2 2 2 19824_002 Open the handle by removing the filter cover. To remove the filter cartridge: Grab the bottom flap with your thumb and index finger. Gently push the filter cartridge toward the impeller and raise up the bottom part of it. Slide the filter cartridge back few millimetres, then remove it.
  • Page 36 If the device is used with damaged filter cartridge, air inlet, air outlet or seals, it irretrievably damages inner components. Precautions: ▶ The BLK2GO needs technical assistance from a Leica Geosystems author- ised service centre if: Any filter mesh is damaged. •...
  • Page 37: Technical Data

    Shutter Global System Performance System performance All ± accuracy specifications are one sigma (1σ) under ☞ and accuracy Leica Geosystems standard test conditions unless otherwise noted. Accuracy of single measurement Value at 78% albedo Angle (horizontal/vertical) 30"/30" 3D point accuracy ±3 mm @ 10 m...
  • Page 38: Electrical Data

    Scanning laser Value Wavelength 830 nm (invisible) Electrical Data BLK2GO power supply Internal battery 7.2 V DC; one internal battery provided with the instrument. Battery operating and Internal battery Value charging times Operating time > 40-45 minutes operating, continuous use at room temperature.
  • Page 39: Dimensions

    Weight [lbs] Leica BLK2GO 0.655 nominal 1.4 nominal AC power supply for GKL821 GKL821 charging station GEB821 battery Leica BLK2GO transport container (without scanner and accessor- ies) Leica BLK2GO transport container (with scanner and standard accessories) Accessories Scope of delivery Included standard accessories: Battery GEB821 (3 ×)
  • Page 40: Dangerous Goods Regulations

    Hereby, Leica Geosystems AG declares that the radio equipment type • BLK2GO is in compliance with Directive 2014/53/EU and other applicable European Directives. The full text of the EU declaration of conformity is available at the fol- lowing Internet address: http://www.leica-geosystems.com/ce.
  • Page 41 Leica Geosystems has developed Guidelines on “How to carry Leica ☞ products” and “How to ship Leica products” with Lithium batteries. Before any transportation of a Leica product, we ask you to consult these guidelines on our web page (http://www.leica-geosystems.com/dgr) to ensure that you are in accordance with the IATA Dangerous Goods Regulations and that the Leica products can be transported correctly.
  • Page 42 Rights, Limitation of Liability, Exclusion of other Assurances, Governing Law and Place of Jurisdiction. Please make sure, that at any time you fully comply with the terms and conditions of the Leica Geosystems Software Licence Agreement. Such agreement is provided together with all products and can also be referred to and downloaded at the Leica Geosystems home page at http://leica-geosystems.com/about-us/compliance-standards/legal-documents...
  • Page 44 896179-1.0.0en Original text (896179-1.0.0en) Printed in Switzerland © 2019 Leica Geosystems AG, Heerbrugg, Switzerland Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Switzerland Phone +41 71 727 31 31 www.leica-geosystems.com...

Table of Contents

Save PDF