Yaesu FTM-6000R Operating Manual page 11

[F menu] key
Press briefly
Press the [F menu] key to display the function list screen. Rotate the DIAL knob to select an item and perform
the functions and make settings.
In the factory default setting, the items in gray of the table below are registered to the function list. The regis-
tration can be canceled at any time.
Add registration:
Cancel registration: Turn the DIAL knob to select the registered item to cancel → Press and hold the [SQL
Press and hold
Press and hold the [F menu] key to enter the menu list. The Menu list permits configuring the various func-
tions according to individual operating needs and preferences. (Refer to page 35).
The items in gray are registered to the "function list" in advance, briefly press the [F menu] key to call them.
Enables/Disables the Automatic Power Off
01 APO
feature.
02 AR MOD Select the ARTS Beep mode.
Select the Polling Interval during ARTS op-
03 AR INT
eration.
Enables/Disables the Busy Channel Lock-
04 BCLO
Out feature.
05 BEEP Set the beep level.
Select the CTCSS/DCS/EPCS Bell Ringer
06 BELL
repetitions.
07 CLK.TYP Shift the CPU clock frequency.
Sets of the front panel display illumination
08 DIMMER
level.
Enables/Disables the DTMF Autodialer fea-
09 DTMF
ture.
10 DT TX Loads the DTMF Autodialer Memories.
11 DT MEM Register a DTMF code.
12 HOME Recall the home channel.
13 MIC.GIN Adjust the microphone gain level.
14 MIC.PGM
Program the function assigned to the Micro-
PGM.P1
phone [ P1 ] key.
Program the function assigned to the Micro-
PGM.P2
phone [ P2 ] key.
Program the function assigned to the Micro-
PGM.P3
phone [ P3 ] key.
Program the function assigned to the Micro-
PGM.P4
phone [ P4 ] key.
15 PAGER
Set the Receive Pager Code for Enhanced
PAG.CDR
CTCSS Paging & Code Squelch functions.
Sett the Transmit Pager Code for Enhanced
PAG.CDT
CTCSS Paging & Code Squelch functions.
16 PKT.SPD DATA communication baud rate settings.
17 RX MODE Select the receive mode.
Set the frequency bands that can be select-
18 BND.SEL
ed.
Press and hold the [F menu] key → Turn the DIAL knob to select the item to register
→ Press and hold the [F menu] key.
back] key.
Menu list
Reverses the transmit and receive repeater
19 RPT.REV
offset frequencies.
Set the Repeater offset frequency Shift di-
20 RPT.SET
rection.
21 RPT.OTR
Activate/Deactivate the Automatic Repeater
RPT.ARS
Shift feature.
RPT.FRQ Set the magnitude of the Repeater Shift.
22 SCN.ON Engages the Scan operation.
23 SCN.TYP
SCN.RSM Select the Scan Resume mode.
Enables/Disables the "Dual Watch Revert"
DW RVT
feature.
Selects the Tone Encoder and/or Decoder
24 SQL.TYP
mode.
Setting of the CTCSS Tone Frequency or
25 SQL.COD
the DCS code.
Enables/Disables the split CTCSS/DCS
26 SQL.EXP
coding.
27 STEP Sets the frequency synthesizer steps.
Indicates the current temperature inside the
28 xx.xF
transceiver.
29 TOT Set the Time-Out Timer.
30 TX PWR Set the transmit power level.
31 VER.DSP Display the transceiver software version.
32 xx.xV Display the DC Supply Voltage.
Set the FM transmit modulation level and
33 WIDTH
receiver bandwidth.
34 WX ALT Weather alert operation setting.
35 BLT
BLT.OFF Set the Bluetooth function.
BLT.LST Bluetooth device list.
BLT.SAV Set the Bluetooth save function.
BLT.AF Set the Bluetooth receive audio output.
9