Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zaxcom ZMT270
Summary of Contents for Zaxcom ZMT270
- Page 1 USER MANUAL Published October 2019 Firmware Version ZMT270 ZMT3-HH Smart Audio...
-
Page 2: Table Of Contents
ZMT3 HM TRANSMITTER ......................... 4 HOME SCREEN ............................6 MAIN MENU ..............................7 ................................7 ICROPHONE UHF T ............................... 7 RANSMIT REQUENCY ................................ 7 RANSMITTER SUB MENUS ..............................8 ..................................8 ENU GROUPS ........................8 CCESSING AND NAVIGATING THE MENU GROUPS .......................... - Page 3 FIRMWARE WITH A TRANSMITTER ....................24 ZMT3-HH PDATING FIRMWARE WITH A TRANSMITTER OPERATING FREQUENCIES ........................25 ........................25 EMOTE ONTROL AND ..................................25 UHF - A UDIO PRODUCT SUPPORT ..........................26 SPECIFICATIONS ............................. 27 ZAXCOM WARRANTY POLICY AND LIMITATIONS ..............28...
-
Page 4: Zmt3 Hm Transmitter
Zaxcom ZMT3-HH Transmitter ZMT3 HM Transmitter 1. Microphone Capsule - The ZMT3-HH can use any Shure compatible microphone capsule. 2. LED Light Ring 3. OLED Display XLR View - When looking at the OLED Display the INC key will be on the top and the DEC key will be on the bottom seperated by the MENU key. - Page 5 Zaxcom ZMT3-HH Transmitter 1. Micro SD Card Slot Inserting a Micro SD card: With the OLED screen of the transmitter facing you, turn the card so the finger contacts are facing you and pointing down toward the slot. Insert the card into the slot and press it down until you hear a slight click.
-
Page 6: Home Screen
Zaxcom ZMT3-HH Home Screen Home Screen ZaxNet Status Transport Power Frequency Modulation Status Level 543.2 STOP 09:18:03:00 ZHD96 05 attery Level Audio Meter Gain Indicators at -20, -10, 0 dBFS Frequency - This is the transmit frequency of the ZMT3-HH. -
Page 7: Main Menu
Zaxcom ZMT3-HH Main Menu Main Menu To cycle through the main menu press the MENU key. Microphone Gain Set GAIN 20 dB The microphone gain is adjusted from this menu. To increase the gain press the INC key and to decrease the gain press the DEC key. -
Page 8: Sub Menus
Zaxcom ZMT3-HH Menu Navigation Sub Menus Menu groups The ZMT3-HH has six sub menu groups Record - Changes the parameters of the on-board recorder. • Transmit - Changes the parameters of the UHF transmitter. • ZaxNet - Changes the parameters of the ZaxNet transceiver. -
Page 9: Record Menu
Zaxcom ZMT3-HH Record Menu RECORD MENU SD Card Format This menu will only appear if a card was inserted prior to booting up PRESS UP KEY 5X: TO ERASE CARD The Micro SD card is erased and formatted from this menu. Please note that all cards need to be formatted in the ZMT3-HH prior to recording. -
Page 10: Time Left On Card
Zaxcom ZMT3-HH Record Menu Time Left on Card This menu will only appear if a card was inserted prior to booting up TIME LEFT 20 H TIME USED 4 H ____ This page displays the remaining time left on the card as well as the time already recorded on the card. -
Page 11: Transmit Menu
Zaxcom ZMT3-HH Transmit Menu TRANSMIT MENU UHF Transmitter Power Level Set TX POWER: 50MW The UHF transmit power of the ZMT3-HH is set from this page. The transmit power can be adjusted to output 25, 50 or 75mW. The higher the power setting the more battery power will be required. -
Page 12: Zaxnet Menu
Zaxcom ZMT3-HH ZaxNet Menu ZAXNET MENU ZaxNet Mode ZAXNET MODE: TX This menu sets the mode of the ZaxNet receiver. OFF - The ZaxNet transceiver is disabled. The ZMT3-HH will not receive ZaxNet commands or time code and • it will not transmit any ZaxNet audio. Please note if ZaxNet mode is set to OFF the several ZaxNet menu items will not appear. -
Page 13: Low Power Zaxnet
ZaxNet commands. Therefore the different group codes allow each person to be independent and not interfere with each other. Most users leave the group set to 1 on all of their Zaxcom products. Group codes can be set from 1 to 99. -
Page 14: Zaxnet Receive Before Transmit Time
Zaxcom ZMT3-HH ZaxNet Menu ZaxNet Receive Before Transmit Time Receive only mode. RX TO TX TIME: The ZaxNet transceiver will only receive ZaxNet and NOT go into OFF (NORMAL RX) transmit mode. Therefore no ZaxNet TC and/or audio will be transmitted. -
Page 15: Audio Menu
Zaxcom ZMT3-HH Audio Menu AUDIO MENU High Pass Filter HIGH PASS FILTER: 90Hz ____ The high pass filter is turned on and adjusted from this menu. The high pass filter range is 70Hz to 220Hz in 10Hz increments. 2K Notch Filter 2K NOTCH FILTER The 2K notch filter is useful in removing digital RF interference that can be introduced into some microphones. -
Page 16: Dynamics
Zaxcom ZMT3-HH Audio Menu Dynamics DYNAMICS The dynamics is a soft knee compressor that is located after the analog to digital converter which will limit the dynamic range to prevent clipping during occurrences of loud audio. Dynamics is comprised of both a... -
Page 17: Time Code Menu
Zaxcom ZMT3-HH Time Code Menu TIME CODE MENU Time Code Frame Rate Set TIMECODE 23.98 GEN 09:18:05:02 ____ The time code frame rate menu is where the time code frame rate is set. The ZMT3-HH will lock to and record all standard time code frame rates. -
Page 18: Setup Menu
Zaxcom ZMT3-HH Setup Menu SETUP MENU LED Color LED COLOR: BLUE This menu sets the color of the LED light ring. The light ring can be set to OFF, BLUE, GREEN, CYAN, RED, MAGENTA, YELLOW, or WHITE. LED Ring Mode LED RING MODE: This menu controls when the light ring illuminates. -
Page 19: Key Lock On Boot Up
Zaxcom ZMT3-HH Setup Menu Standby Mode After Boot Up STANDBY B00T MODE: NORMAL MODE This menu sets what power mode the ZMT3-HH boots up to. NORMAL MODE - The transmitter will boot up normally. • STANDBY MODE - The transmitter boots up in low power standby mode. The transmitter will be waiting for •... -
Page 20: Qrx / Erx Firmware Update
Zaxcom ZMT3-HH Setup Menu QRX / ERX Firmware Update PRESS TO SEND QRX PROG FILE This page is used to update the firmware on a QRX or ERX receiver. If the ZaxNet mode is set to OFF or receive (RX) this menu will allow for QRX firmware to be updated - if the ZaxNet mode is set to transmit (TX) then this menu will allow for ERX to be updated. -
Page 21: Encryption Code Set
Zaxcom ZMT3-HH Setup Menu Encryption Code Set ID1: 000 ID2: 000 If an encryption code is set the transmitted audio will be encrypted and can only be listened to if the receiver has the matching encryption code entered. When receiving an audio signal and the codes do not match, all that will be heard is white-noise or silence. -
Page 22: Media
The media card is formatted using a FAT32 file system. While recording, the unit places all recorded audio in a single file on the media. The files generated by the recorder (.zax format) can only be recognized by Zaxcom’s ZaxConvert program. Using ZaxConvert will transfer the file to a Broadcast Wave or MP3 file. ZaxConvert is available to anyone for free from the Zaxcom website http://www.zaxcom.com/support/updates/... -
Page 23: Firmware
WARNING: Before updating the firmware be sure to insert a fresh battery and do not power down the unit during the update process, if the unit should lose power during the upgrade, it may need to be sent back to Zaxcom for repair. -
Page 24: Updating Qrx Firmware With Azmt3-Hh Transmitter
Zaxcom ZMT3-HH Firmware Updating QRX firmware with a ZMT3-HH transmitter 1. Format a micro SD card in a ZMT3-HH transmitter. 2. With a computer take the formatted card and perform the following: Delete the “SNXXXX.ME” file from the card. •... -
Page 25: Operating Frequencies
Zaxcom ZMT3-HH Antenna Cutting Chart Operating Frequencies ZaxNet - Remote Control and Time Code 2.403 to 2.475 GHz UHF - Audio ZMT3-HH.5 512.0 MHz to 614.0 MHz (Blocks 20 through 23) ZMT3-HH.6 596.0 MHz to 698.0 MHz (Blocks 23 through 26) -
Page 26: Product Support
Download the latest Firmware from: http://zaxcom.com/support/updates/ Download the latest User Manuals from: http://zaxcom.com/support/updates/ Submit Technical Questions at: http://www.zaxcom.com/submit-a-technical-question Submit information for Repair Services at: http://www.zaxcom.com/support/repairs Join the Zaxcom User Forum at: http://www.zaxcom.com/forum/forum.php Join the Zaxcom Face Book User Group at: https://www.facebook.com/groups/682199065139938/... -
Page 27: Specifications
Zaxcom ZMT3-HH Specifications Specifications Transmitter Power output: 25 / 50 / 75 mW – Firmware Selectable RF Modulation: Proprietary Digital Method RF Frequency Range: ZMT3-HH.5: 512 - 614 MHz ZMT3-HH.6: 596 -698 MHz Antenna Connector: 50 Ω SSMA Female Emission Designator: 180 KV2E FCC Part: 75.861... -
Page 28: Zaxcom Warranty Policy And Limitations
Product exists to repair or replace a defective Product. Zaxcom’s replacement Product under its limited warranty will be manufactured from new and serviceable used parts. Zaxcom’s warranty applies to repaired or replaced Product for the balance of the applicable period of the original warranty or thirty days from the date of shipment of a repaired or replaced Product, whichever is longer. - Page 29 à faible puissance exempts de licence dans les bandes de télévision» USA - FCC Part 74, FCC Identifier PR6ZMT3-HH Canada - Industry Canada RSS 210, IC:12755A-ZMT3-HH Zaxcom Digital Wireless are protected under following patent #’s: 4,327,066 / 7,711,443 / 7,929,902 / 8,385,814 / 8,878,708 / 8,842,854...