Advertisement
Quick Links
Warranty Statement:
All of our products sold are guaranteed to be free from
defects in workmanship and materials for
from date of purchase, unless otherwise stated. TPC
will repair or replace any defective part at no charge.
TPC will not be responsible for labor charges or
shipping charges to / from the TPC facility. This
guarantee does not cover normal wear or stains on
surface finish. The guarantee does not cover damage
resulting
from
improper
accidents incurred in shipping and handling. All claims
against the freight carrier must be initiated at the time
the damaged items are received. The claim is the
responsibility of the customer. We are improving our
products on a continuous basis. We reserve the right to
make
modifications
notification and are not obliged to modify previously
manufactured items. Bulbs and batteries are not
covered under any type of warranty.
851 S. Lawson St
City of Industry CA 91748
800-560-8222
service@tpcdental.com
www.tpcdental.com
installation,
misuse
without
the
need
for
one
year
or
prior
PC 2530 User Manual
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for TPC PC 2530
Summary of Contents for TPC PC 2530
- Page 1 TPC will repair or replace any defective part at no charge. TPC will not be responsible for labor charges or shipping charges to / from the TPC facility. This guarantee does not cover normal wear or stains on surface finish.
- Page 2 Markings Figures Check for internal leaks inside the machine. Notice: Risk of losing accessories and documents Unit is very loud when the The motor should ramp un in rpms motor is running. once in the on position. Check for any suction clogs if the motor appears to Caution: Risk of injury or malfunction be strained. If the motor makes loud screeching sounds, discontinue use Read carefully of the manual. and contact TPC support. The unit powers on and when Check internal waste container and I remove the suction valve verify its empty. Check level probes the motor will not turn on. inside the tank and verify they are Ground Protective clean. If the probes become corroded you may need to clean them with an abrasive cloth or pad. The fuse continues to blow Short or fault in the electrical circuit. Electron garbage bin Call TPC tech support for further assistance.
- Page 3 Care and maintenance Setting up unit for operation Clean Solids Collector trap or replace as needed. Connect power cable to inlet power port on the back of the Turn unit off. Turn lid of solids unit as shown. canister counter clockwise and Replacement Power Cord: remove lid. Remove trap and Part Number: PC2530N-PC replace as needed. Trap size is 2 1/8” Item Code. 53016-L Once usage is complete, Its recommended that clean water be purged through the machine. Vacuum approximately two cups of Turn the power switch to the water through the suction “on” position and the unit’s air lines, Allow waste container to compressor will cycle on. drain. This will remove any left over waste in the lines. Turn the power switch to the “off” position to discontinue use. Should you encounter a blown fuse they are located in two places. The internal power inlet has a 15 amp 250 Volt fuse. 5 x 20 mm. Install waste container onto the back of the PC 2630 unit. Secondary Fuse Assembly located on Main PCB...
- Page 4 Setting up unit for operation General use Instructions Set waste container onto Lift Desired suction valve to be ledge as shown. used. Once the Suction Valve is removed from the hanger the motor will automatically turn “ON”. Make sure the additional suction Valve Spool Levers are in the Closed Position. Place Suction Valve back in to the hanger and the motor will automatically turn “Off”. Install the drain Line as shown During use, if the internal waste container becomes full the motor will automatically turn off. Once this occurs the unit will begin to automatically drain the internal waste tank into the waste container on the back of the machine. Place unit in desired location for use. Lock wheels in place Once the draining is complete once unit is in the desired the motor will automatically operating position. Unlock turn “ON” again. wheel lock to move unit. Note: If the HP holder switch gets stuck in the on position, the unit motor will continue to operate...
Need help?
Do you have a question about the PC 2530 and is the answer not in the manual?
Questions and answers