Toyota PC170-0K01A Installation Manual
Toyota PC170-0K01A Installation Manual

Toyota PC170-0K01A Installation Manual

Body side molding

Advertisement

INSTALLATION MANUAL BODY SIDE MOLDING
Thank you for your purchase of TOYOTA genuine "BODY SIDE MOLDING" This manual explains the procedure
for installation, Please read this manual before installation to ensure correct installation.
PART NUMBER
PC170-0K01A
1
2
NO.
PART NUMBER
1
PC170-0K01C
2
PC170-0K01F
PC170-0K01B
3
PC170-0K01D
4
5
-
6
-
7
-
8
-
9
-
10
-
APPLICABLE MODEL
HILUX 2015 (D-CAB ONLY)
3
4
(Body Side Molding FR LH)
(Body Side Molding RR
(Body Side Molding FR
(Body Side Molding RR
A
(Template
A)
B-RH
(Template
B-RH)
B-LH
(Template
B-LH)
C-RH
(Template
C-RH)
C-LH
(Template
C-LH)
(Installation
Manual)
INSTALLATION TOOLS/MATERIALS
1. Clean Cloth
2. Adhesive Tape
3. Degreasing Agent
4. Scissor or Cutter
5. Heat Gun (when temperature is 15 ํ C or Lower)
6. Laser Digital Thermometer
5
A
8
9
Time to installation : 30 min.
PART NAME
LH)
RH)
RH)
INSTALLATION REQUIREMENTS
1. Temperature Range : 15 ํ - 55 ํ C
2. Installation Force : 49N ±1N
Rev.#1 (Eng. 24-08-18)
ุ REMARK
-
Component Parts
6
7
10
Q'TY
1
1
1
1
8
1
1
1
1
1
1.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PC170-0K01A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Toyota PC170-0K01A

  • Page 1 Rev.#1 (Eng. 24-08-18) INSTALLATION MANUAL BODY SIDE MOLDING Thank you for your purchase of TOYOTA genuine “BODY SIDE MOLDING” This manual explains the procedure for installation, Please read this manual before installation to ensure correct installation. ุ REMARK PART NUMBER...
  • Page 2 Rev.01 1. Perform the installation indoors where it is not subjected to dust. If the air temperature is 15 ํ C CAUTION or lower, the adhesive strength will be reduced. In order to prevent such problems, use a heat gun to warm up the installation surface of the vehicle and the double-sided adhesive tape to a temperature between 15 ํ...
  • Page 3 Rev.01 Installation Method 1. Clean and degrease the shaded area using clean cloth with degreasing agent as shown in Fig. 1 C-RH B-RH END of R END of R 500mm 50mm 50mm 750mm 50mm 2. Position of sticker template. C-RH B-RH 2.1 Attach sticker template...
  • Page 4 Rev.01 C-RH B-RH 3. Trial fit (do not remove release liner) and check position of parts on both front and rear door mouldings by aligning them to the sticker templates. NOTE: If vehicle door panels and door mouldings are not at the required temperature, heat up vehicle door panels and door moulding.
  • Page 5 Rev.01 C-RH 6. Repeat Steps 4 and 5 for rear door mould. 7. Open doors to full opening angle to ensure moulds do not interfere with body panel. Remove the remaining release liners in the direction according to Fig. 7. Check all release liners have been removed as failure to do this may cause the product to drop off or peel off.

Table of Contents