Technical Data; Working Instructions; Specified Conditions Of Use - Milwaukee M18 ONEBLHPT Original Instructions Manual

TECHNICAL DATA

Press device
Production code
Frequency band(s) of Bluetooth
Radio-frequency power
Bluetooth version
Battery voltage
Power consumption
Nominal force
Compression range:
Ø Plastics & Composite pipes
Ø Metal until
Weight according EPTA-Procedure 01/2014
(Li-lon 2,0 Ah ... 12,0 Ah)
Weight
(M18 ONEBLHPT / Li-Ion 2.0 Ah / J18-Th14) 4,7 kg
Noise information
Measured values determined according to EN 60745. Typically, the
A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty
K=3dB(A))
Sound power level (Uncertainty K=3dB(A)) 86 dB (A)
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according
to EN 60745
Vibration emission value a
h
Uncertainty K=
WARNING!
The vibration and noise emission level given in this information
sheet has been measured in accordance with a standardized test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the
main applications of the tool. However if the tool is used for diffe-
rent applications, with different accessories or poorly maintained,
the vibration and noise emission may differ. This may significantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should
also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi-
cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm, organization of work
patterns.
WARNING Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
PRESS DEVICE SAFETY WARNINGS
M18 ONEBLHPT
Use protective equipment. Always wear goggles when using the
machine. The use of protective clothing is recommended, such as
4777 60 02 ...
dust mask, protective gloves, sturdy non-slip footwear, helmet and
... 000001-999999
ear defenders.
2402 - 2480 MHz
Never hold your fingers or other body parts in the working area of
1,8 dBm
the cylinder or the press jaws.
4.2 BT signal mode Do not hold the jaw levers with your hands during the pressing
operation.
18 V
Press tools and press devices must only be used by trained
450 W
personnel.
32 kN
Check the press tools and press devices for cracks and other signs of
wear before each use.
Only use press tools and press devices that are in perfect technical
63 mm (110 mm)
54 mm (108 mm) condition.
dep. on system
Have damage repaired immediately by an authorised workshop.
The machine may only be used with a press jaw inserted into it.
2,9 ... 3,9 kg
In the event of problems during the pressing process, press the
Emergency Stop button immediately and release the ON switch.
The valve will open and the piston will return to its initial position.
Compliance with the specified service work and service intervals is
mandatory.
Remove the battery pack before starting any work on the
appliance.
75 dB (A)

WORKING INSTRUCTIONS

Use only system-compatible press fittings and press jaws designed
for them.
Consult the documents provided by the system supplier for hand-
ling and assembly instructions for fittings and pipes.
Check whether the nominal width of the press fitting corresponds
to the nominal width of the press jaws.
<2,5 m/s
2
Make sure that the press jaw is fully closed when pressing is
1,5 m/s
2
complete.
Imperfect pipe joints must be compressed again using a new
fitting.
After finishing the work, check the installation with appropriate
testing equipment and assure that it is leakproof!
The press device is not suitable for continuous operation. Following
30 minutes of continuous operation, a short break of at least 15
minutes must be taken to allow the device to cool down.

SPECIFIED CONDITIONS OF USE

The devices and the press jaws are designed exclusively for the
press-fitting of pipes and fittings for which the relevant press jaws
are intended.
These press devices are intended exclusively for use with press jaws
approved by Milwaukee in agreement with the system supplier.
ONE-KEY™
To learn more about the ONE-KEY functionality of this device,
please refer to the Quick Start guide included with this product or
go to http://www.milwaukeetool.com/one-key
To download the ONE-KEY app, visit the App Store or Google Play
from your smart device.
We considered the result to be within our minimum acceptable
performance level according to EN 301 489-1/ EN 301 489-17.
Deutsch English
15 15
GB