Related Manuals for Yaesu FTM-3200DE
Summary of Contents for Yaesu FTM-3200DE
- Page 1 FTM-3200DR/DE Advance Manual VHF DIGITAL/ANALOG TRANSCEIVER C4FM/FM DIAL M H z V / M TXPO SETUP...
-
Page 2: Table Of Contents
Contents Basic Operation ......................3 Microphone Gain Setting ....................3 RF Squelch ........................3 Advanced Operation ...................... 4 Programming the Key Assignments ................4 Split Tone Operation ....................... 5 Tone Search ........................6 DCS Search ........................7 EPCS (Enhanced Paging & Code Squelch) Operation ..........8 Storing CTCSS Tone Pairs for EPCS Operation ............ -
Page 3: Basic Operation
Basic Operation Microphone Gain Setting The microphone gain has been programmed at the factory to a level that should be satisfactory for the supplied MH-48A6JA Microphone. If an after-market microphone is used, you may wish to set a different Mic Gain level. 1. -
Page 4: Advanced Operation
Advanced Operation Programming the Key Assignments Default FTM-3200DR key functions have been assigned to the Microphone [ P3 ] / [ P4 ] keys at the factory. The user may change these key function assignments, if quick access to another function is desired. Note: The default setting: [ P3 ] - WIRES [ P4 ] - WX CH (T CALL: EXP/European version) To change the assignments for the programmable keys:... -
Page 5: Split Tone Operation
Advanced Operation Split Tone Operation The FTM-3200DR can be configured to operate in a “Split Tone” system via the Setup menu, to facilitate operation on repeaters using a mix of both CTCSS and DCS control. 1. Press and hold in the [ MHz ( SETUP )] key for one second to enter the Set mode. -
Page 6: Tone Search
Advanced Operation Tone Search When the CTCSS tone being transmitted by another station is not known, you can tune the radio to the incoming signal and activate tone scan to search for and identify the tone being used. To scan for the tone in use: 1. -
Page 7: Dcs Search
Advanced Operation DCS Search When the DCS code being transmitted by another station is not known, you can tune the radio to the incoming signal and activate DCS code scan to search for and identify the DCS code being used. To scan for the DCS in use: 1. -
Page 8: Epcs (Enhanced Paging & Code Squelch) Operation
Advanced Operation EPCS (Enhanced Paging & Code Squelch) Operation The FTM-3200DR includes an Enhanced CTCSS tone encoder/decoder and a dedicated microprocessor providing paging and selective calling features. This allows placing a call to a specific station (Paging), and choosing to receive calls directed only to you (Code Squelch). -
Page 9: Activating The Enhanced Paging & Code Squelch System
Advanced Operation Activating the Enhanced Paging & Code Squelch System 1. Press and hold in the [ MHz ( SETUP )] key for one second to enter the Set mode. 2. Rotate the DIAL knob to select “SQL TYPE DIAL 39”. -
Page 10: Dtmf Operation
Advanced Operation DTMF Operation DTMF tones (Dual Tone Multi Frequencies) are the tones you hear when dialing from a telephone keypad. The FTM-3200DR transceiver can transmit the DTMF codes by using the keys on the microphone or recalling registered number strings from memories. The maximum of 16-digit DTMF codes can be registered in up to 10 memory channels. -
Page 11: Registering A Dtmf Code
Advanced Operation Registering a DTMF code 1. Press and hold in the [ MHz ( SETUP )] key for one second to enter the Set mode. 2. Rotate the DIAL knob to select “DT SET 16”. DIAL M H z V / M TXPO SETUP... -
Page 12: Transmitting The Registered Dtmf Code
Advanced Operation Transmitting the registered DTMF code 1. Press and hold in the [ MHz ( SETUP )] key for one second to enter the Set mode. 2. Rotate the DIAL knob to select “DT AUTO DIAL 14”. M H z V / M TXPO SETUP... -
Page 13: Setting Dtmf Autodialer Tx Delay Time
Advanced Operation Setting DTMF Autodialer TX delay time A longer delay may be set between the time the transmitter is keyed and the first DTMF digit is sent: 1. Press and hold in the [ MHz ( SETUP )] key for one second to enter the Set mode. -
Page 14: Memory Operation
Memory Operation Split Memory A separate transmit frequency may be registered to a memory channel to which a receive frequency has already been registered. 1. In the VFO mode, select the transmit frequency to be registered. 2. Press and hold the [ V/M ( MW )] key for one second. A memory number will appear in the bottom right corner of the display. -
Page 15: Naming A Memory Channel
Memory Operation Naming a Memory Channel You may wish to append an alphanumeric “Tag” (label) to each memory, to aid in recollection of the channel’s use (such as club name, etc.). 1. Recall the memory channel on which you wish to append a label. 2. -
Page 16: Scanning
Scanning Scan Resume Options Select one of the three receiving operations to be performed after the scanning stops. (1) Restart scanning after receiving the frequency for the set amount of time. Select from 2.0 to 10.0 seconds (0.5 step). (2) Continue receiving the frequency until the signal disappears, and then restart scan- ning 2 seconds after the signal disappears (BUSY). -
Page 17: Memory Skip Scanning
Scanning Memory Skip Scanning When some memory channels are continuously active, you may wish to skip them during scanning, but still have them available for manual selection. To mask a memory to be skipped (only) during scanning, use the following procedure: 1. -
Page 18: Preferential Memory Scan
Scanning Preferential Memory Scan The FTM-3200DR also allows setting up a “Preferential Scan List” of channels, which you can “flag” within the memory system. The flagged channels are designated by an “ ” icon when they are selected, one by one, for the Preferential Scan List. When memory scanning is initiated beginning on a channel with the “... -
Page 19: Programmable Memory Scan (Pms)
Scanning Programmable Memory Scan (PMS) The FTM-3200DR can be set to tune or scan only the frequencies between user-defined lower and band limits. Example: Set up a PMS channel by registering a lower frequency of 144.300 MHz, and an upper frequency of 148.000 MHz to the L1/U1 memory channels. Registering to the programmable memory channels 1. -
Page 20: Scanning The Programmable Memory Channels
Scanning Scanning the programmable memory channels 1. Press the [ V/M ( MW )] key to enter memory mode. 2. Turn the DIAL knob, or use the microphone keypad, to recall the upper or lower fre- quency PMS memory channel (L1 or U1). 3. -
Page 21: Priority Channel Scanning (Dual Watch)
Scanning Priority Channel Scanning (Dual Watch) The FTM-3200DR’s scanning features include a two-channel scanning capability which allows operating on a VFO, Memory channel, or Home channel, while periodically checking a user- defined Memory Channel for activity. If a station received on the Memory Channel is strong enough to open the Squelch, the scanner will pause on that station in accordance with the Scan-Resume mode setting of Menu item “SCAN RSM 36.”... -
Page 22: Gm Function
GM Function GM Alert Beep To alert you to the current status of GM operation, the GM (Group Monitor) feature allows two kinds of alert beeps (with the additional option of turning them off). Depending on your location and the potential annoyance associated with frequent beeps, you may choose the Beep mode which best suits your needs. -
Page 23: Clone
Clone The FTM-3200DR includes a convenient “Clone” feature, which allows the memory and configuration data from one transceiver to be transferred to another FTM-3200DR. This can be particularly useful when configuring a number of transceivers for a public service operation. Here is the procedure for cloning data from one radio to another: 1. -
Page 24: Setup (Menu) Mode
Setup (Menu) Mode The FTM-3200DR Setup (Menu) mode, already described in parts of many previous chapters, is easy to activate and setup. The Menus may be used to configure many of transceiver parameters, some of which have not been detailed previously. Use the following procedure to activate the Setup (Menu) mode: 1. - Page 25 Setup (Menu) Mode Menu Item Function Available Values Default Setting of the DTMF Autodialer Sending 17: DT SPEED 50 / 100 50 MS Speed. Enables/Disables the “Priority Channel 18: DW RVRT ON / OFF Revert” feature. Enables/Disables the alert sound when IN RANGE / ALWAYS / 19: GM RINGR detecting stations within communication...
- Page 26 Setup (Menu) Mode Menu Item Function Available Values Default AUTO / 5 / 6.25 / 10 / 40: STEP Sets the frequency synthesizer steps. 12.5 / 15 / 20 / 25 / 50 / AUTO 100 (kHz) Indicates the current temperature inside 41: TEMP the transceiver.
-
Page 27: Menu Selection Details
Menu Selection Details 1 APO Function: Enables/Disables the Automatic Power Off feature. Available Values: 0.5 H to 12.0 H (0.5 H/step) / OFF Default: OFF 2 BCLO Function: Enables/Disables the Busy Channel Lock-Out feature. Available Values: ON / OFF Default: OFF 3 BEP KEY Function: Enables/Disables the key beeper. - Page 28 Menu Selection Details 9 DCS CODE Function: Setting of the DCS code. DCS CODE Available Values: 104 standard DCS codes 023 025 026 031 032 036 043 047 051 053 054 065 071 072 073 074 114 115 116 122 Default: 023 125 131 132 134 143 145 152 155 156 162 165 172 174 205 212 223 225 226 243 244...
- Page 29 Menu Selection Details 14 DT AUTO Function: Enables/Disables the DTMF Autodialer feature. Available Values: MANUAL / AUTO Default: MANUAL 15 DT DELAY Function: Setting of the DTMF Autodialer’s TX Delay Time. Available Values: 50 / 250 / 450 / 750 / 1000 ms Default: 450 ms 16 DT SET Function: Loading of the DTMF Autodialer Memories.
- Page 30 Menu Selection Details 22 LOCK Function: Selects the Control Locking Lockout combination. Available Values: KEY+DIAL / PTT / KEY+PTT / DIAL+PTT / ALL / KEY / DIAL Default: KEY+DIAL 23 MIC GAIN Function: Adjust the microphone gain level. Available Values: LEVEL 1 - LEVEL 9 Default: LEVEL 5 24 MEM NAME Function: Programming an Alpha/Numeric label for a Memory Channel.
- Page 31 Menu Selection Details 27 PAG CD-R Function: Setting the Receiver Pager Code for the Enhanced CTCSS Paging & Code Squelch function See page 8 for details. 28 PAG CD-T Function: Setting the Transmitting Pager Code for the Enhanced CTCSS Paging & Code Squelch function.
- Page 32 Menu Selection Details 35 RPT SFT Function: Sets the Repeater Shift direction. Available Values: - RPT / + RPT / SIMPLEX Default: SIMPLEX 36 SCAN RSM Function: Selects the Scan Resume mode. Available Values: BUSY / HOLD / 2.0 SEC - 10.0 SEC (0.5 SEC step) Default: 5.0 SEC BUSY: The scanner will hold until the signal disappears, then will resume...
- Page 33 Menu Selection Details 40 STEP Function: Sets the frequency synthesizer steps. Available Values: AUTO / 5 / 6.25 / 10 / 12.5 / 15 / 20 / 25 / 50 / 100 (kHz) Default: AUTO 41 TEMP Function: Indicates the current temperature inside the transceiver. 42 TONE FRQ Function: Setting of the CTCSS Tone Frequency.
- Page 34 Menu Selection Details 48 WX VOL Function: Selects the audio output level of the Weather Alert. Available Values: NOR VOL / MAX VOL Default: NOR VOL 49 W/N DEV Function: Reduction of the Microphone Gain/Deviation and receiver bandwidth. Available Values: WIDE / NARROW Default: WIDE 50 MY CALL Function: Sets your station call sign.
- Page 35 Copyright 2019 YAESU MUSEN CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD. YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress, CA 90630, U.S.A.