Honeywell NOTIFIER NFW-100X Operating Instructions Manual page 15

Read Status
Pressing 2 while viewing the Program Check screen #1 will display a screen which will indicate if any output zones have not been pro-
grammed to at least one input zone. Use the up and down arrow keys to view all zones.
Pressing 3 while viewing the Program Check screen #1 will display a screen which will indicate if any input zones have not been pro-
grammed to at least one output zone. Use the up and down arrow keys to view all zones.
4.24.8 History
Pressing 3 while viewing Read Status Screen #3 will display the following screen:
The operator can view all events which have been stored in the history file, only alarms or other events, such as troubles or supervisories,
by pressing the corresponding number key.
4.24.9 Annunciators
READ STATUS
1=ANNUNCIATORS
2=COMMUNICATOR
Read Status Screen #4
Pressing 1 or 2 for ANN-BUS while viewing the Annunciator Screen allows the operator to view the settings and devices for each ANN-
BUS. Press 1 for the Primary ANN-BUS and 2 for the Secondary ANN-BUS.
The ANN-BUS Screen #1 indicates if the ANN-BUS has been enabled Yes or disabled No.
Pressing 2 for Modules Installed while viewing ANN-BUS Screen #1 will display screens for ANN-BUS Addresses 1 -8 and the devices
installed at each address. A subscreen will display the options that have been programmed for each device.
ANN-BUS SELECT
1=PRIMARY
2=SECONDARY
3=ANN-BUS OPTIONS
Annunciator Screen
Pressing 1 for ANN-S/PG Options while viewing ANN-BUS Screen #2 will display the options selected for the installed N-ANN-S/PG
annunciators.
Pressing 2 for ANN-LED Options while viewing ANN-BUS Screen #2 will display the options selected for the installed N-ANN-LED
annunciators.
Pressing 3 for ANN-80/100 Options while viewing ANN-BUS Screen #2 will display the options selected for the installed N-ANN-80 or
N-ANN-100 annunciators.
4.24.10 Communicator
READ STATUS
1=ANNUNCIATORS
2=COMMUNICATOR
Read Status Screen #4
COMMUNICATOR
INSTALLED YES
2=POTS SETTINGS
3=IP SETTINGS
Communicator Screen #1
The Communicator Screen #1 indicates if an IPOTS-COM has been installed Yes or No.
NFW-100X Manual — P/N LS10131-001NF-E:C 7/25/2018
1=VIEW ALL
2=VIEW ALARMS
3=VIEW OTHER EVENTS
Pressing 1 while viewing Read Status Screen #4 will display the following screens:
ANN-BUS SELECT
1=PRIMARY
2=SECONDARY
3=ANN-BUS OPTIONS
Annunciator Screen
ENABLED
2=MODULES INSTALLED
CLASS A
ANN-BUS Screen #1
Pressing 3 for ANN-BUS Options while viewing the Annunciator Screen allows the operator to view the
settings for any N-ANN-S/PG, N-ANN-LED, N-ANN-80, and N-ANN-100 installed in the system.
1=ANN-S/PG OPTIONS
2=ANN-LED OPTIONS
3=ANN-80/100 OPTIONS
ANN-BUS Screen #2
Pressing 2 while viewing Read Status Screen #4 will display the following screens:
COMMUNICATOR
1=PRI COMM PATH
2=SEC COMM PATH
TBL REPORT LIMIT 0
Communicator Screen #2
HISTORY
ANN-BUS
NO
NO
ANN-BUS
COMMUNICATOR
1=EVENT CODES
TEST TIME INT
24HR TEST TIME
Communicator Screen #3
Operating Instructions
COMMUNICATOR
REPORT STYLE
24
0100
Communicator Screen #4
POINT
117