Table of Contents
Advertisement
Micro-USB connector
This connector is used to configure and update the system with Pandora Alarm Studio or Pandora
Specialist App.
Main cable
The main cable contains low-current programmable channels: inputs «INP» and outputs «CH» with a
preset logic. Changing the preset logic is available in the system settings «Inputs and outputs» or «Time
channels» menus. Additionally, in the «Input settings» submenu the «INP» channels can be reassigned
from the normally open type «NO» (the system reacts to the appearance of the potential corresponding
to the scheme) to the normally closed type «NC» (the system reacts to the disappearance of the
potential corresponding to the scheme).
• Wire №1 | Red | POWER SUPPLY (+12V) 10A — System power supply. It should be securely
connected to the reliable conductor with a constant voltage of +12V. The wire is equipped with a
10A fuse.
• Wire №2 | Black | GROUND (-) — ground. It should be connected to a vehicle grounding spot (-).
This wire should be connected FIRST during the installation.
• Wire №3 | White — channel for connecting of the external temperature sensor, default logic is
«Engine temperature sensor». It is connected to the red wire of the sensor, the black wire of the
sensor is connected to the ground (-).
• Wire №4 | White/red | LED/VALET — channel for connecting the external VALET button. It is
connected to the red wire of the external button.
• Wire №5 | Yellow | (+) | INP1 — default setting is positive status «Ignition» input. It is connected to
the ignition switch or other wire, where +12V appears when the ignition is turned on and does not
disappear until the ignition is turned off. This input is mandatory for connection.
• Wire №6 | Green | 200mA (-) | INP2/CH4 — default setting negative status «NC blocking» output.
Channel for controlling the blocking relay with a normally closed contact group (the channel is
enabled when: the system is armed and ignition being switched on, the system is disarmed but the
Immobiliser or Anti-hi-Jack mode is enabled and the ignition being switched on).
• Wire №7 | Grey | 200mA (-) | CH1/INP4 — default setting negative status «Clutch» input. Is used
for system arming/disarming in the presence of authorization devices (see 1.2.4 setting «Arming/
disarming by clutch lever»). It is connected to the wire what becomes grounded when the clutch
lever is pressed.
• Wire №8 | Orange/black | CAN-L - digital bus «CAN-Low». It is connected to the corresponding
CAN-Low wire of the vehicle. Before connecting the digital bus, you must select the vehicle model
(model code). Information available on www.loader.pandorainfo.com and in the Pandora Specialist
App and Pandora Alarm Studio.
26
PA N D O R A S M A R T M OTO / S M A R T M OTO P LU S
• Wire №9 | Orange | 6A (+12V) | CH7 — default logic is «Turn indicators». Connect this wire to (+)
control wire of the left or right turn indicators. The wire is equipped with a 7.5A fuse.
• Wire №10 | Orange | 6A (+12V) | CH6 — default logic is «Turn indicators». Connect this wire to (+)
control wire of the left or right turn indicators. The wire is equipped with a 7.5A fuse.
• Wire №11 | Purple | 2A (+12V) | CH5 — default logic is «Siren». Connect this wire to +12V wire
of the siren. When using owner's authorization devices and Immobiliser or Anti-hi-Jack modes, it is
recommended to set both «Siren» and «Beeper» logic in the settings.
• Wire №12 | White/Green | LED/VALET — channel for connecting the external VALET button. It is
connected to the black wire of the external button.
• Wire №13 | White/blue | (+) | INP3 — default logic is «Brake». Connect this wire to a wire where
+12V appears when the brake pedal or lever is pressed.
• Wire №14 | White/brown | 200mA (-) | CH2/INP5 — default logic is «Trunk». Connect this wire to a
wire that becomes grounded when the pannier opens. It is necessary to change the input type from
NO to NC in the «Inputs settings» if a magnetic reed sensor is used.
• Wire №15 | Brown | 200mA (-) | CH3/INP6 — default logic is «Trunk». Connect this wire to a wire that
becomes grounded when the pannier opens. It is necessary to change the input type from NO to NC
in the «Inputs settings» if a magnetic reed sensor is used.
• Wire №16 | Orange/black | CAN-H — digital bus «CAN-High». It is connected to the corresponding
CAN-High wire of the vehicle. Before connecting the digital bus, you must select the vehicle model
(model code). Information available on www.loader.pandorainfo.com and in the Pandora Specialist
App and Pandora Alarm Studio.
U S E R A N D I N S TA L L AT I O N M A N UA L
27
Advertisement
Table of Contents
