Page 1 Foreword Congratulations on choosing a SUBARU vehicle. This Owner’s Manual has all the information necessary to keep your SUBARU in excellent condition and to properly maintain the emission control system for minimizing emission pollutants. We urge you to read this manual carefully so that you may understand your vehicle and its operation.
Page 4: Seat, Seatbelt And Srs Airbags
Warranties & Warranties for U.S.A. All SUBARU vehicles distributed by Subaru of America, Inc. and sold at retail by an authorized SUBARU dealer in the United States come with the following warranties. . SUBARU Limited Warranty . Emission Control Systems Warranty .
Page 5: Climate Control
This chapter informs you how to keep your SUBARU looking good. Chapter 11: Maintenance and service This chapter informs you when you need to take your SUBARU to the dealer for scheduled maintenance and informs you how to keep your SUBARU running properly.
Page 6: Abbreviation List
& Abbreviation list You will find several abbreviations in this manual. The meanings of the abbrevia- tions are shown in the following list. Abbreviation Meaning Air conditioner Automatic/Emergency locking A/ELR retractor Anti-lock brake system Anti knock index Automatic locking retractor Automatic transmission Automatic transmission fluid All-wheel drive...
Page 7 Mark Name Child restraint top tether an- chorages Horn Windshield wiper deicer Wiper intermittent Windshield wiper and washer Windshield wiper mist (for single wipe) Rear window wiper Rear window washer Lights Headlight beam leveler Parking lights, tail lights, li- cense plate lights and instru- ment panel illumination Mark Name...
Page 8: Child Safety
Safety precautions when driving & Seatbelt and SRS airbag WARNING . All persons in the vehicle should fasten their seatbelts BEFORE the vehicle starts to move. Other- wise, the possibility of serious injury becomes greater in the event of a sudden stop or acci- dent.
Page 9 at all times in a child restraint device or in a seatbelt. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or improperly restrained.
Page 10: Drinking And Driving
& Drinking and driving WARNING Drinking and then driving is very dangerous. Alcohol in the blood- stream delays your reaction and impairs your perception, judgment and attentiveness. If you drive after drinking - even if you drink just a little - it will increase the risk of being involved in a serious or fatal accident, injuring or killing yourself, your passengers and others.
Page 11: Tire Pressures
& Modification of your vehicle CAUTION Your vehicle should not be modified other than with genuine SUBARU parts and accessories. Other types of modifications could affect its performance, safety or durability, and may even violate governmental regulations.
Page 12: California Proposition 65
& California proposition 65 warning WARNING Engine exhaust, some of its consti- tuents, and certain vehicle compo- nents contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addi- tion, certain fluids in vehicles and certain components of product wear contain or emit chemicals known to...
Page 13 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 14: Table Of Contents
Table of contents Seat, seatbelt and SRS airbags Keys and doors Instruments and controls Climate control Audio Interior equipment Starting and operating Driving tips In case of emergency Appearance care Maintenance and service Specifications Consumer information and Reporting safety defects Index...
Page 15 Illustrated index & Exterior Engine hood lock release (page 11-4) Headlight switch (page 3-26) Bulb replacement (page 11-38) Wiper switch (page 3-33) Moonroof (page 2-25) Roof rail (if equipped) (page 8-13) Door locks (page 2-5) Tire pressure (page 11-25) Flat tires (page 9-6) 10) Tire chains (page 8-11) 11) Fog light switch (page 3-31) 12) Tie-down hooks (page 9-15)
Page 16 Rear gate (page 2-24) Rear wiper switch (page 3-34) Rear window defogger button (page 3-36) Fuel filler lid and cap (page 7-3) Child safety locks (page 2-21) Tie-down hooks (page 9-15) Bulb replacement (page 11-38) Towing hook (page 9-14) – CONTINUED –...
Page 17 & Interior ! Passenger compartment area Seatbelt (page 1-17) Lower anchorages for child restraint system (page 1-38) Center console (page 6-6) Front seat (page 1-2) Second-row seat (page 1-8) Third-row seat (page 1-13)
Page 18 Cargo area light (page 6-3) Dome lights (page 6-2) Second-row center seatbelt (page 1-24) Sun visors (page 6-4) Map light (page 6-3) Top tether anchorages (second-row seat) (page 1-41) Top tether anchorages (third-row seat) (page 1-42) – CONTINUED –...
Page 19 Select lever (page 7-13) Hazard warning flasher switch (page 3-5) Multi function display (page 3-23) Glove box (page 6-6) Audio (page 5-1) Climate control (page 4-1) Cup holder (page 6-8)
Page 20 & Instrument panel Door locks (page 2-5) Illumination brightness control (page 3-28) Remote control mirror switch (page 3-41) Power folding mirror switch (if equipped) (page 3-42) Windshield wiper deicer (page 3-35) Traction Control system OFF switch (page 7-27) Headlight beam leveler (if equipped) (page 3-29) Light control switch (page 3-26) Combination meter (page 3-5)
Page 21 & Light control and wiper control levers/switches Parking light switch (page 3-31) Windshield wiper (page 3-32) Mist (page 3-33) Windshield washer (page 3-34) Rear window wiper and washer switch (page 3-34) Wiper intermittent time control switch (page 3-33) Wiper control lever (page 3-33) Light control switch (page 3-26) Fog light switch (page 3-31) 10) Headlight ON/OFF (page 3-26)
Page 22 & Combination meter ! U.S.-spec. models Temperature gauge (page 3-9) Tachometer (page 3-7) Speedometer (page 3-6) Fuel gauge (page 3-8) Trip meter and odometer (page 3-6/page 3-7) Trip meter A/B selection and trip meter reset knob (page 3-7) Select lever/Gear position indicator (page 3-20) –...
Page 23 ! Except U.S.-spec. models Temperature gauge (page 3-9) Tachometer (page 3-7) Speedometer (page 3-6) Fuel gauge (page 3-8) Trip meter and odometer (page 3-6/page 3-7) Trip meter A/B selection and trip meter reset knob (page 3-7) Select lever/Gear position indicator (page 3-20)
Page 24: Warning And Indicator Lights
& Warning and indicator lights Mark Name Page Driver’s seatbelt warning 3-10 light Front passenger’s seat- 3-10 belt warning light SRS airbag system 3-11 warning light CHECK ENGINE warn- ing light/Malfunction indi- 3-12 cator lamp Charge warning light 3-13 Oil pressure warning light 3-13 AT OIL TEMP warning 3-13...
Page 25: Cargo Area
& Cargo area Jack handle (page 9-19) Maintenance tools (page 9-19) Jack (page 9-19) Spare tire (page 9-5)
Page 26 Function settings A SUBARU dealer can change the settings of the functions shown in the following table to meet your personal requirements. Contact the nearest SUBARU dealer for details. If your vehicle is equipped with the genuine SUBARU navigation system, the settings for some of these functions can be changed using the navigation monitor.
Page 27 Item Function Seatbelt warning Sounds a chime while driving Possible settings Default setting Operation/Non-operation Operation Page 1-18...
Page 28 Top tether anchorages ... 1-14 *SRS airbag (Supplemental Restraint 1-15 System airbag)... 1-16 Your vehicle’s SRS configuration ... SUBARU advanced frontal airbag system ... 1-17 SRS side airbag and SRS curtain airbag... 1-18 SRS airbag system monitors... SRS airbag system servicing ... 1-18 Precautions against vehicle modification ...
Page 29: Front Seats
Seat, seatbelt and SRS airbags Front seats WARNING . Never adjust the seat while driv- ing to avoid the possibility of loss of vehicle control and of personal injury. . Before adjusting the seat, make sure the hands and feet of rear seat passengers or luggage are clear of the adjusting mechan- ism.
Page 30: Power Seat
TOO CLOSE TO THE SRS AIRBAG. According to accident statistics, children are safer when properly restrained in the rear seating posi- tions than in the front seating posi- tions. For instructions and precau- tions concerning child restraint sys- tems, refer to “Child restraint sys- tems”...
Page 31: Memory Function (Driver's Seat - If Equipped)
Seat, seatbelt and SRS airbags To adjust the seat cushion angle, pull up or push down the front end of the control switch. ! Seat height adjustment (driver’s seat) To adjust the seat height, pull up or push down the rear end of the control switch. &...
Page 32: Head Restraint Adjustment
. Be sure to press the correct button to retrieve your registered seat position. If the seat position is not optimum for you, it may adversely affect your driving and may reduce the effectiveness of the seatbelt. That could result in an accident involving serious injury or death.
Page 33: Active Head Restraint
. If your vehicle is involved in a rear-end collision, have an authorized SUBARU dealer in- spect the active head restraints. . The active head restraints may not operate in the event the vehicle experiences only a slight impact in the rear.
Page 34: Lumbar Support
& Lumbar support Pull the lever forward or backward. Pulling the lever forward will increase the amount of support for your lower back. Pulling the lever backward will decrease the amount of support for your lower back. Seat heater (if equipped) The seat heater is equipped in the front seats.
Page 35: Second-Row Seats
Seat, seatbelt and SRS airbags Second-row seats WARNING . Seatbelts provide maximum re- straint when the occupant sits well back and upright in the seat. Do not put cushions or any other materials between occupants and seatbacks or seat cushions. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen...
Page 36: Reclining The Seatback
When the right seat or the left seat pair is slid rearward, it stops partway at the lock point so as not to trap the legs of passengers sitting on the third-row seat. It is possible to slide the seat or seat pair further rearward by releasing the lock that stops it.
Page 37: Folding Down The Seatback
1-10 Seat, seatbelt and SRS airbags Pull the lever up and adjust the seatback to the desired position. Then release the lever and make sure the seatback is securely locked into place. & Folding down the seatback WARNING . Never allow passengers to ride on the folded seatback or in the cargo area.
Page 38 By pulling the tab on the center seat, you can fold only the seatback of the center seat. To return the seatback to its original position, raise the seatback until it locks into place. Make sure it is securely locked. CAUTION .
Page 39: Head Restraint Adjustment
1-12 Seat, seatbelt and SRS airbags & Head restraint adjustment Both the rear window side seats and the rear center seat are equipped with head restraints. WARNING . Never drive the vehicle with the head restraints removed because they are designed to reduce the risk of serious neck injury in the event that the vehicle is struck from the rear.
Page 40: Armrest
Head restraint Release button To raise: Pull the head restraint up. To lower: Push the head restraint down while pressing the release button on the top of the seatback. The head restraint should be adjusted so that the center of the head restraint is closest to the top of the occupant’s ears.
Page 41: Access To The Third-Row Seat
1-14 Seat, seatbelt and SRS airbags WARNING Never stack luggage or other cargo higher than the top of the seatback because it could tumble forward and injure passengers in the event of a sudden stop or accident. & Access to the third-row seat There are levers on both sides of the second-row seat.
Page 42: Folding Down The Seatback
& Folding down the seatback WARNING . Never allow passengers to ride on the folded seatback or in the cargo area. Doing so may result in serious injury or death. . Secure skis and other long items properly to prevent them from being thrown around inside the vehicle and causing serious in- jury during a sudden stop, a...
Page 43: Head Restraint Adjustment
1-16 Seat, seatbelt and SRS airbags & Head restraint adjustment Both the third-row seats are equipped with head restraints. WARNING . Never drive the vehicle with the head restraints removed because they are designed to reduce the risk of serious neck injury in the event that the vehicle is struck from the rear.
Page 44: Seatbelts
Seatbelts & Seatbelt safety tips WARNING . All persons in the vehicle should fasten their seatbelts BEFORE the vehicle starts to move. Other- wise, the possibility of serious injury becomes greater in the event of a sudden stop or acci- dent.
Page 45: Emergency Locking Retractor (Elr)
1-18 Seat, seatbelt and SRS airbags the face or neck, adjust the shoulder belt anchor height (window-side seating posi- tions only) and then if necessary move the child closer to the belt buckle to help provide a good shoulder belt fit. Care must be taken to securely place the lap belt as low as possible on the hips and not on the child’s waist.
Page 46 For further details about canceling the warning operation, please contact your SUBARU dealer. If there is no passenger on the front passenger’s seat, the seatbelt warning device for the front passenger’s seat will be deactivated.
Page 47: Fastening The Seatbelt
If the seatbelt warning device for front passenger’s seat still does not function correctly after taking relevant corrective actions described above, immediately contact your SUBARU dealer for an inspection. & Fastening the seatbelt WARNING . Never use a belt that is twisted or reversed.
Page 48 ! Front seatbelts 1. Adjust the seat position according to the following procedure. Driver’s seat: Adjust the seatback to the upright position. Move the seatback as far from the steering wheel as practical while still maintaining full vehicle control. Front passenger’s seat: Adjust the seat- back to the upright position.
Page 49 1-22 Seat, seatbelt and SRS airbags WARNING When wearing the seatbelts, make sure the shoulder portion of the webbing does not pass over your neck. If it does, adjust the seatbelt anchor to a lower position. Placing the shoulder belt over the neck may result in neck injury during sudden braking or in a collision.
Page 50 ! Adjusting the shoulder belt anchor height (second-row seats) The shoulder belt anchor height should be adjusted to the position best suited for the passenger. Always adjust the anchor height so that the shoulder belt passes over the middle of the shoulder without touching the neck.
Page 51 1-24 Seat, seatbelt and SRS airbags ! Second-row center seatbelt Center seatbelt tongue plate Connector (tongue) Connector (buckle) Center seatbelt buckle WARNING Fastening the seatbelt with the web- bing twisted can increase the risk or severity of injury in an accident. When fastening the belt after it is pulled out from the retractor, espe- cially when inserting the connec-...
Page 52 2. Pull out the seatbelt slowly from the overhead retractor. 3. After confirming that the webbing is not twisted, insert the connector (tongue) attached at the webbing end into the buckle on the right-hand side until a click is heard. Make sure that the “ ”...
Page 53 1-26 Seat, seatbelt and SRS airbags Push the release button of the center seatbelt buckle (on the left-hand side) to unfasten the seatbelt. 1. Insert a key or other hard pointed object into the slot in the connector (buckle) on the right-hand side and push it in, and the connector (tongue) plate will disconnect from the buckle.
Page 54 ! Third-row seatbelt 1. Sit well back in the seat. 2. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly.
Page 55: Seatbelt Maintenance
. Pretensioners are designed to func- tion on a one-time-only basis. In the event that a pretensioner is activated, both the driver’s and front passenger’s seatbelt retractor assemblies must be replaced and only by an authorized SUBARU dealer. When replacing seat-...
Page 56: System Monitors
. If the front seatbelt retractor assem- bly or surrounding area has been damaged, contact your SUBARU dealer as soon as possible. . When you sell your vehicle, we urge you to explain to the buyer that it has seatbelt pretensioners by alerting him to the contents of this section.
Page 57: System Servicing
SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbags will operate improperly (e.g.
Page 58: Precautions Against Vehicle Modification
& Precautions against vehicle modification Always consult your SUBARU dealer if you want to install any accessory parts to your vehicle. CAUTION Do not perform any of the following modifications. Such modifications can interfere with proper operation of the seatbelt pretensioners.
Page 59: Where To Place A Child Restraint System
& Where to place a child re- straint system The following are SUBARU’s recommen- dations on where to place a child restraint system in your vehicle. A: Front passenger’s seat You should not install a child restraint...
Page 60 contours of the seat cushion and can be securely retained using the seatbelt. C: Second-row center seat Installing a child restraint system is not recommended, although the A/ELR seat- belt and an upper anchorage (tether anchorage) are provided in this position. Some types of child restraints might not be able to be secured firmly due to projection of the seat cushion.
Page 61: Choosing A Child Restraint System
1-34 Seat, seatbelt and SRS airbags & Choosing a child restraint system Choose a child restraint system that is appropriate for the child’s age and size (weight and height) in order to provide the child with proper protection. The child restraint system should meet all applic- able requirements of Federal Motor Vehi- cle Safety Standards for United States or...
Page 62 6. Take up the slack in the lap belt. 7. Pull out the seatbelt fully from the retractor to change the retractor over from the Emergency Locking Retractor (ELR) to the Automatic Locking Retractor (ALR) mode. Then, allow the belt to rewind into the retractor.
Page 63 1-36 Seat, seatbelt and SRS airbags NOTE When the child restraint system is no longer in use, remove it and restore the ELR mode of the retractor. That mode is restored by retracting the seatbelt fully. ! Installing forward facing child re- straint 1.
Page 64: Installing A Booster Seat
Second-row seat Third-row seat 10. If the child restraint system requires a top tether, latch the hook onto the top tether anchor and tighten the top tether. For additional instructions, refer to “Top tether anchorages” F1-41. 11. To remove the child restraint system, press the release button on the seatbelt buckle and allow the belt to retract completely.
Page 65: Installation Of Child Restraint Systems By Use Of Lower And Tether Anchorages (Latch)
1-38 Seat, seatbelt and SRS airbags creased. 1. Slide the seat or seat pair to its rearmost position. 2. Place the booster seat in the rear seating position and sit the child on it. The child should sit well back on the booster seat.
Page 66 restraint system in your vehicle. Unsecured child restraint sys- tems can be thrown around in- side of the vehicle in a sudden stop, turn or accident; they can strike and injure vehicle occu- pants as well as result in serious injuries or death to the child.
Page 67 1-40 Seat, seatbelt and SRS airbags The tether anchorages (upper an- chorages) are provided for all the seating positions of the second-row seat. On each outboard rear/second-row seat, you will find marks “ ” at the bottom of the seatback. Each lower anchorage is located where the seat cushion meets the seatback.
Page 68: Top Tether Anchorages
If you have any question concerning this type of child restraint system, ask your SUBARU dealer. & Top tether anchorages Your vehicle is equipped with five top tether anchorages so that a child restraint system having a top tether can be installed in a rear seating position.
Page 69 1-42 Seat, seatbelt and SRS airbags ! Third-row seat Two tether anchorages are attached to the rear edge of the cargo area. Open the cover flap to use each ancho- rage. ! To hook the top tether ! Second-row seat 1.
Page 70 CAUTION When the child restraint system is to be secured using the top tether, pass the top tether under the head restraint between the head restraint stay posts. CAUTION Be sure to install the top tether with the head restraint raised to the highest position.
Page 71 1-44 Seat, seatbelt and SRS airbags 3. Fasten the top tether hook of the child restraint system to the appropriate upper anchorage. 4. Tighten the top tether securely. CAUTION Do not pass the top tether under the head restraint. The top tether will touch the head restraint and the resulting slack will prevent its se- cure installation.
Page 72: Srs Airbag (Supplemental Restraint System Airbag)
*SRS airbag (Supplemental Restraint System airbag) *SRS: This stands for supplemental re- straint system. This name is used be- cause the airbag system supplements the vehicle’s seatbelts. Your vehicle is equipped with a crash sensing and diagnostic module, which will record the use of the seatbelt(s) by the driver and front passenger when any of the SRS frontal, side and curtain airbags...
Page 73 1-46 Seat, seatbelt and SRS airbags ment, the driver should always sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full vehicle control and the front passenger should move the seat as far back as possible and sit upright and well back in the seat.
Page 74 blems after SRS airbag deploys, get fresh air promptly. . A deploying SRS airbag releases hot gas. Occupants could get burned if they come into direct contact with the hot gas. NOTE When you sell your vehicle, we urge you to explain to the buyer that it is equipped with SRS airbags by alerting him or her to the applicable section in this Owner’s Manual.
Page 75 1-48 Seat, seatbelt and SRS airbags ! Components Airbag control module (including impact and rollover sensors) Frontal airbag module (driver’s side) Frontal airbag module (front passenger’s side) Front sub sensor (left-hand side) Front sub sensor (right-hand side) Side airbag module (driver’s side) Side airbag module (front passenger’s side) Side airbag sensor (center pillar left-hand...
Page 76: Subaru Advanced Frontal Airbag System
& SUBARU advanced frontal airbag system Your vehicle is equipped with a SUBARU advanced frontal airbag system that com- plies with the new advanced frontal airbag requirements in the amended Federal Motor Vehicle Safety Standard (FMVSS) No. 208. The SUBARU advanced frontal airbag system automatically determines the de- ployment force of the driver’s SRS frontal...
Page 77 1-50 Seat, seatbelt and SRS airbags WARNING Never hold a child on your lap or in your arms. The SRS airbag deploys with considerable force and can injure or even kill the child. WARNING The SRS airbag deploys with con- siderable speed and force.
Page 78 SRS frontal airbag even when the driver’s SRS frontal airbag deploys. This is normal. Observe the following precautions. Failure to do so may prevent the SUBARU advanced frontal airbag system from functioning correctly or cause the system to fail.
Page 79 . Do not remove or disassemble the front passenger’s seat. . Do not install any accessory (such as an audio amplifier) other than a genuine SUBARU accessory under the front pas- senger’s seat. . Do not place anything (shoes, umbrel- la, etc.) under the front passenger’s seat.
Page 80 ! Conditions in which front passen- ger’s SRS frontal airbag is not activated The front passenger’s SRS frontal airbag will not be activated when any of the following conditions are met regarding the front passenger’s seat. . The seat is empty. .
Page 81 Owner’s Manual and immediately contact your SUBARU dealer for an inspection. NOTE When a child who has outgrown a child restraint system or a small adult is seated in the front passenger’s seat,...
Page 82 SUBARU advanced air- bag system. If you have any questions, you may contact the following SUBARU distributors.
Page 83 Driver’s side Passenger’s side The SRS airbag can function only when the ignition switch is in the “ON” position. The SUBARU advanced frontal airbag system is designed to determine the activation or deactivation condition of the front passenger’s SRS frontal airbag depending on the total load on the front passenger’s seat monitored by the front...
Page 84 components can be very hot as a result of deployment. The driver’s SRS frontal airbag and front passenger’s SRS frontal airbag are de- signed to deploy in the event of an accident involving a moderate to severe frontal collision. It is basically not designed to deploy in lesser frontal impacts be- cause the necessary protection can be achieved by the seatbelt alone.
Page 85: Seat, Seatbelt And Srs Airbags
1-58 Seat, seatbelt and SRS airbags both driver’s and front passenger’s SRS frontal airbags may be activated when the vehicle sustains a hard impact in the undercarriage area from the road surface (such as when the vehicle plunges into a deep ditch, is severely impacted or knocked hard against an obstacle on the road such as a curb).
Page 86 ! Examples of the types of accidents in which deployment of the driver’s/driver’s and front passenger’s SRS frontal airbag(s) is unlikely to occur. 1-59 Seat, seatbelt and SRS airbags The vehicle strikes an object, such as a telephone pole or sign pole. The vehicle slides under the load bed of a truck.
Page 87: Srs Side Airbag And Srs Curtain Airbag
1-60 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which the driver’s/driver’s and front passenger’s SRS frontal airbag(s) will basically not deploy. The driver’s and front passenger’s SRS frontal airbags are designed basically not to deploy if the vehicle is struck from the side or from behind, or if it rolls onto its side or roof, or if it is involved in a low- speed frontal collision.
Page 88 for third-row seat occupants. WARNING The SRS side airbag and SRS curtain airbag are designed as only a supplement to the primary protec- tion provided by the seatbelt. They do not do away with the need to fasten seatbelts. It is also important to wear your seatbelt to help avoid injuries that can result when an occupant is not seated in a proper...
Page 89 1-62 Seat, seatbelt and SRS airbags WARNING . Never allow a child to kneel on the front passenger’s seat facing the side window or to wrap his/ her arms around the front seat seatback. In the event of an accident, the force of the SRS side airbag deployment could injure the child seriously be- cause his/her head or arms or...
Page 90 A hands-free microphone or other accessory in such a loca- tion could be propelled through the cabin with great force by the curtain airbag, or it could prevent correct deployment of the curtain airbag. In either case, the result could be serious injuries. WARNING Do not hang coat hangers or other hard or pointed objects on the coat...
Page 91 1-64 Seat, seatbelt and SRS airbags right center pillars and rear wheel houses. Another impact sensor, which also senses impact force, is located under the second- row center seat. In addition, a rollover sensor is located inside the airbag control module.
Page 92 itself. Also, the SRS curtain airbag de- ploys depending on the vehicle’s position and inclination at the time of the rollover. ! Example of the type of accident in which the SRS side airbag will most likely deploy. A severe side impact near the front seat activates the SRS side airbag.
Page 93 1-66 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which the SRS curtain airbag will most likely deploy. A severe side impact near the front seat or the rear seat activates the SRS curtain airbag. The vehicle rolls onto its side or the roof.
Page 94 ! Examples of the types of accidents in which it is possible that the SRS side airbag and the SRS curtain airbag will deploy. 1-67 Seat, seatbelt and SRS airbags Hitting a curb, edge of pavement or hard surface Falling into or jumping over a deep hole Landing hard or vehicle falling It is possible that the SRS side and curtain airbags will deploy if a serious impact...
Page 95 1-68 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which the SRS side airbag is unlikely to deploy. The vehicle is involved in an oblique side-on impact. The vehicle is involved in a side-on impact in an area outside the vicinity of the passenger compartment.
Page 96 ! Examples of the types of accidents in which the SRS curtain airbag is unlikely to deploy. 1-69 Seat, seatbelt and SRS airbags The vehicle is involved in an oblique side-on impact. The vehicle is involved in a side-on impact in an area outside the vicinity of the passenger compartment.
Page 97 1-70 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which the SRS side airbag and SRS curtain airbag will basically not deploy. The vehicle is involved in frontal collision with another vehicle (moving or station- ary).
Page 98: Srs Airbag System Monitors
SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbags will operate improperly (e.g.
Page 99: Srs Airbag System Servicing
CAUTION If you need service or repair in areas indicated in the following list, have the work performed by an author- ized SUBARU dealer. The SRS air- bag control module, impact sensors and airbag modules are stored in these areas.
Page 100 . Attachment of any equipment (side steps or side sill protectors, etc.) other than genuine SUBARU accessory parts to the side body. Always consult your SUBARU dealer if you want to install any accessory parts on your vehicle. 1-73 Seat, seatbelt and SRS airbags...
Page 101 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 102 Keys ... Key number plate ... Immobilizer ... Security ID plate... Security indicator light ... Key replacement ... Door locks ... Locking and unlocking from the outside ... Locking and unlocking from the inside ... Battery drainage prevention function ... Power door locking switches ...
Page 103: Keys And Doors
Keys and doors Keys Master key Submaster key Valet key Key number plate Security ID plate Three types of keys are provided for your vehicle. Master key, submaster key and valet key. The master key and submaster key fit all locks on your vehicle.
Page 104: Immobilizer
Immobilizer CAUTION FCC WARNING Changes or modifications not ex- pressly approved by the party re- sponsible for compliance could void the user’s authority to operate the equipment. The immobilizer system is designed to prevent an unauthorized person from starting the engine. Only keys registered with your vehicle’s immobilizer system can be used to operate your vehicle.
Page 105: Security Indicator Light
If the security indicator light does not flash, the immobilizer system may be malfunc- tioning. If this occurs, contact your SUBARU dealer as soon as possible. In case an unauthorized key is used (e.g. an imitation key), the security indicator light illuminates.
Page 106: Door Locks
Door locks & Locking and unlocking from the outside To lock the driver’s door from the outside with the key, turn the key toward the front. To unlock the door, turn the key toward the rear. Lift the outside door handle to open an unlocked door.
Page 107: Battery Drainage Prevention Function
The operational/non-operational setting of this function can be changed by a SUBARU dealer. Contact your SUBARU dealer to change the setting. NOTE . The factory setting (default setting) for this function is set as “operational”.
Page 108: Power Door Locking Switches
gate are completely closed. . The battery drainage prevention function does not operate while the key is in the ignition switch. Power door locking switches Driver’s switch Lock Unlock Keys and doors Front passenger’s switch Lock Unlock All doors and the rear gate can be locked and unlocked by the power door locking switches located at the driver’s side and the front passenger’s side doors.
Page 109: Key Lock-In Prevention Function
This function’s operational/non-opera- tional setting can be changed by a SUBARU dealer. Contact a SUBARU dealer for details. NOTE When leaving the vehicle, make sure you are holding the key before locking the doors.
Page 110: Locking The Doors
to the following two conditions: (1) This device may not cause harmful inter- ference, and (2) this device must accept any interference received, in- cluding interference that may cause undesired operation. Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.
Page 111: Unlocking The Doors
Map light: OFF position Dome light: DOOR position Cargo area light: DOOR position A SUBARU dealer can change the illumi- nation period setting of the interior lights in accordance with your preference. Contact the nearest SUBARU dealer for details.
Page 112: Sounding A Panic Alarm
5. The turn signal lights flash 3 times to indicate completion of the setting. You may have the above settings done by your SUBARU dealer. & Replacing the battery CAUTION . Do not let dust, oil or water get on or in the transmitter when repla- cing the battery.
Page 113: Replacing Lost Transmitters
2-12 Keys and doors 2. Open the key head using a flat-head screwdriver. 3. Remove the transmitter case from the key head. 4. Open the transmitter case by releasing the hooks. 5. Remove the old battery from the holder. Negative (−) side facing up 6.
Page 114 different. Programming transmitter codes into system: Key tag Transmitter circuit board To register a new transmitter with the remote keyless entry system, it is neces- sary to program the transmitter’s code (identification number) into the system. A tag showing the code is affixed to the key unit, and another is affixed to the circuit board inside the transmitter.
Page 115 2-14 Keys and doors form the whole procedure again begin- ning with part 1. 4. Open and close the door once within 15 seconds. NOTE . When part 4 of the procedure is completed, an electronic tone will sound for 30 seconds. .
Page 116 NOTE . When you finish entering the eighth digit, an electronic tone will sound for 30 seconds. . If the interval between one push of the switch and the next exceeds 5 seconds, an error will occur. In this event, perform the procedure again beginning with part 4.
Page 117: Alarm System
. Map lights The notifications regarding the dome light and the map lights are deactivated as the factory setting. A SUBARU dealer can activate the system. Contact your SUBARU dealer for details. & Activating and deactivating the alarm system To change the setting of your vehicle’s...
Page 118: If You Have Accidentally Triggered The Alarm System
& If you have accidentally trig- gered the alarm system ! To stop the alarm Do any of the following operations. . Press any button on the remote trans- mitter. . Turn the ignition switch to the “ON” position. & Arming the system ! To arm the system using remote transmitter 1.
Page 119: Disarming The System
. The 30-second standby time can be eliminated if you prefer. Have it per- formed by your SUBARU dealer. . The system is in the standby mode for a 30-second period after locking the doors with the remote transmitter. The security indicator light will flash at short intervals during this period.
Page 120: Passive Arming
DOORS MUST BE MANUALLY LOCKED. ! To enter the passive mode If you wish to program the passive arming mode, have it done by your SUBARU dealer. ! Arming the system CAUTION In passive mode, the system will...
Page 121: Tripped Sensor Identification
30 seconds. If you desire, your SUBARU dealer can connect them and set them for activation or deactivation. NOTE . The shock sensors are not always...
Page 122: Child Safety Locks
Child safety locks WARNING Always use the child safety lock whenever a child rides in the rear. Serious injury could result if a child accidentally opened the door and fell out. Each rear door has a child safety lock that prevents the door from being opened even if the inside door handle is pulled.
Page 123 2-22 Keys and doors ! Operating the driver’s window Open Automatically open To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without holding the switch.
Page 124 ! Locking the passengers’ windows Push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed. Press the switch again to cancel the passengers’ window locking. NOTE When the lock switch is pushed to the “LOCK”...
Page 125: Rear Gate
2-24 Keys and doors Rear gate The rear gate can be locked and unlocked using any of the following systems. . Power door locking switch: Refer to “Power door locking switches” F2-7. . Remote keyless entry system (if equipped): Refer to “Remote keyless entry system”...
Page 126: Moonroof (If Equipped)
NOTE If the rear gate cannot be unlocked due to a discharged vehicle battery, a malfunction in the door locking/unlock- ing system or other causes, you can unlock it by manually operating the rear gate lock release lever. For the procedure, refer to “Rear gate –...
Page 127: Tilt Function
2-26 Keys and doors & Tilt function Tilt switch Raise Lower The tilting function will only operate when the moonroof is fully closed. Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt” switch to lower the moonroof.
Page 128: Sun Shade
CAUTION Never attempt to test this function using fingers, hands or other parts of your body. NOTE For the sake of safety, it is recom- mended that you avoid driving with the moonroof fully opened. & Sun shade The sun shade can be slid forward or backward by hand while the moonroof is closed.
Page 129 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 130: Instruments And Controls
Clock ... 3-11 Outside temperature indicator ... Low outside temperature warning ... 3-12 Multi function display (vehicles without a 3-12 genuine SUBARU navigation system)... 3-13 Current fuel consumption ... 3-13 Average fuel consumption ... 3-13 Driving range on remaining fuel ...
Page 131 Instruments and controls Light control switch ... 3-26 Headlights... High/low beam change (dimmer)... Headlight flasher ... Daytime running light system ... Turn signal lever ... 3-28 Illumination brightness control ... 3-28 Headlight beam leveler (if equipped) ... 3-29 Parking light switch ... 3-31 Front fog light switch...
Page 132: Ignition Switch
Ignition switch WARNING . Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.
Page 133: Acc
Instruments and controls & Acc In this position the electrical accessories (radio, accessory power outlet, etc.) can be used. & ON This is the normal operating position after the engine is started. & START CAUTION Do not turn the ignition switch to the “START”...
Page 134: Hazard Warning Flasher
Hazard warning flasher The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works with the ignition switch in any position. To turn on the hazard warning flasher, push the hazard warning button on the instrument panel.
Page 135: Speedometer
Instruments and controls meter needles and gauges when the ignition switch is turned to the “ON” position. To change the current setting, press the trip knob for at least 2 seconds. : Activated : Deactivated With the function deactivated, the combi- nation meter illuminates as follows.
Page 136: Double Trip Meter
“ ”. If the trip meter shows “ ”, immediately contact the nearest SUBARU dealer and have the vehicle communication system inspected. NOTE If you press the trip knob while the trip meter is showing “...
Page 137: Fuel Gauge
Instruments and controls pointer of the tachometer in the red zone. This may cause severe da- mage to the engine. NOTE To protect the engine while the select lever is in the “P” or “N” position, the engine is controlled so that the engine speed may not become too high even if the accelerator pedal is depressed hard.
Page 138: Driver's Seatbelt Warning
& Temperature gauge Normal operating range The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position. The coolant temperature will vary in accordance with the outside temperature and driving conditions. We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range.
Page 139: Seatbelt Warning Light And Chime
: Windshield washer fluid warning light : Door open warning light If any lights do not illuminate, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair. & Seatbelt warning light and chime Your vehicle is equipped with a seatbelt warning device at the driver’s and front...
Page 140: Srs Airbag System Warning Light
If still the seatbelt warning device for front passenger’s seat does not function cor- rectly after taking relevant corrective ac- tions described above, immediately con- tact your SUBARU dealer for an inspec- tion. 3-11 Instruments and controls &...
Page 141: Front Passenger's Frontal Airbag On And Off Indicators
2 seconds. After that, one of the indicators illuminates depending on the status of the front passenger’s SRS frontal airbag determined by the SUBARU ad- vanced frontal airbag system monitoring. If the front passenger’s SRS frontal airbag is activated, the passenger’s frontal airbag ON indicator will illuminate while the OFF indicator will remain off.
Page 142: Charge Warning Light
! Automatic transmission control system warning If the light flashes after the engine starts, it may indicate that the automatic transmis- sion control system is not working prop- erly. Contact your nearest SUBARU deal- er for service immediately. – CONTINUED –...
Page 143: Rear Differential Oil Temperature Warning Light
Park the vehicle for several minutes. After the light turns off, you can start driving. If the light does not turn off, contact the nearest SUBARU dealer for service. NOTE . If the tire pressures are not correct and/or the tires are not all the same...
Page 144: Abs Warning Light
Should the warning light illuminate stea- dily after blinking for approximately one minute, have the system inspected by your nearest SUBARU dealer as soon as possible. WARNING If this light does not illuminate briefly after the ignition switch is...
Page 145: Brake System Warning Light
This indicates your brake system may not be working properly. If the light remains illuminated, have the brakes in- spected by a SUBARU dealer immediately. . If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle.
Page 146: Low Fuel Warning Light
SUBARU dealer for repair. ! Electronic Brake Force Distribution (EBD) system warning The brake system warning light also illuminates if a malfunction occurs in the EBD system. In that event, it illuminates together with the ABS warning light.
Page 147: Windshield Washer Fluid Warning Light
The Vehicle Dynamics Control system is probably malfunctioning under any of the following conditions. Have your vehicle checked at a SUBARU dealer immedi- ately. . The light does not illuminate when the ignition switch is turned to the “ON”...
Page 148: Security Indicator Light
The Vehicle Dynamics Control system is probably malfunctioning under the follow- ing condition. Have your vehicle checked at a SUBARU dealer as soon as possible. . The light does not turn off even after the lapse of several minutes (the engine has warmed up) after the engine has started.
Page 149: Sport Mode Indicator Light
“Acc” or “LOCK” position, and then turn it again to the “ON” position. . If this indicator light and the CHECK ENGINE warning light/malfunction in- dicator lamp flash simultaneously dur- ing driving, have the vehicle checked by your nearest SUBARU dealer.
Page 150: Cruise Control Indicator Light
Clock NOTE If your vehicle is equipped with a genuine SUBARU navigation system, refer to the Owner’s Manual supple- ment for the navigation system. The clock shows the time while the ignition switch is in the “Acc” or “ON”...
Page 151: Outside Temperature Indicator
3-22 Instruments and controls Outside temperature indica- NOTE If your vehicle is equipped with a genuine SUBARU navigation system, refer to the Owner’s Manual supple- ment for the navigation system. U.S.-spec. models Except U.S.-spec. models The outside temperature indicator shows the outside temperature in a range from −22 to 1228F (−30 to 508C) when the...
Page 152: Multi Function Display (Vehicles Without A Genuine Subaru Navigation System)
SUBARU navigation system) NOTE . If your vehicle is equipped with a genuine SUBARU navigation system, refer to the Owner’s Manual supple- ment for the navigation system. . A liquid-crystal display is used in the multi function display. You will find its indications hard to see if you wear polarized glasses.
Page 153: Average Fuel Consumption
3-24 Instruments and controls & Average fuel consumption U.S.-spec. models Except U.S.-spec. models This indication shows the average rate of fuel consumption since the trip meter was last reset. Pressing the trip knob toggles the indica- tion between the average fuel consump- tion corresponding to the A trip meter indication and the average fuel consump- tion corresponding to the B trip meter...
Page 154: Journey Time
amount of fuel remaining in the tank and the average rate of fuel consumption. When the low fuel warning light illumi- nates, the driving range indication flashes for 5 seconds. (The display first switches to the driving range indication if it was originally giving some other indication.) U.S.-spec.
Page 155: Light Control Switch
3-26 Instruments and controls display is giving an indication other than the journey time, the display switches to the journey time, flashes for 5 seconds, and returns to its original indication each time a complete hour has elapsed. NOTE The journey time is reset when the ignition switch is turned to the “LOCK”...
Page 156: High/Low Beam Change (Dimmer)
& High/low beam change (dim- mer) To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the combina- tion meter also illuminates. To switch back to low beam, pull the lever back to the detent position.
Page 157: Turn Signal Lever
3-28 Instruments and controls Turn signal lever To activate the right turn signal, push the turn signal lever up. To activate the left turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return after cornering, return the lever to the neutral position by hand.
Page 158: Headlight Beam Leveler (If Equipped)
3-29 Instruments and controls Headlight beam leveler (if equipped) Adjust the headlight beam level with the following dial positions according to the number of passengers and load condition. – CONTINUED –...
Page 159: Instruments And Controls
3-30 Instruments and controls Dial position Number of front seat occupants 1 or 2 Not applicable Number of 2nd seat Number of 3rd seat occupants occupants Not applicable Not applicable Load in the luggage Trailer towing compartment area No load No load No load Full load...
Page 160: Parking Light Switch
Parking light switch The parking light switch operates regard- less of the ignition switch position. By pushing the front end of this switch, following lights will illuminate. – Parking lights – Front and rear side marker lights – Tail lights –...
Page 161: Wiper And Washer
. Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. Refer to “Windshield washer fluid” F11-30. Also, when driving the vehicle...
Page 162: Windshield Wiper And Washer Switches
. Grease, wax, insects or other mate- rial on the windshield or the wiper blades results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer sur- face of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or...
Page 163: Rear Window Wiper And Washer Switch
3-34 Instruments and controls When the wiper switch is in the “ position, turn the dial to adjust the operat- ing interval of the wiper. The operating interval can be adjusted in nine steps. The intermittent operation interval varies depending on the vehicle speed in any of the adjustment steps (longer when the vehicle speed is low;...
Page 164: Windshield Wiper Deicer
3-35 Instruments and controls the control switch to turn it on again. Your SUBARU dealer can set your wind- shield wiper deicer to the continuous operation mode. Contact your SUBARU dealer for details.
Page 165: Rear Window Defogger Button
If defrosting or defogging is not complete, you have to push the control switch to turn it on again. Your SUBARU dealer can set your rear window defogger to the continuous opera- tion mode. Contact your SUBARU dealer for details.
Page 166: Mirrors
NOTE The outside mirror defogger also oper- ates while the rear window defogger is operating. Mirrors Always check that the inside and outside mirrors are properly adjusted before you start driving. & Type A inside mirror (if equipped) The mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position.
Page 167 3-38 Instruments and controls Period of time multi- Gear Function function position displayed button is pressed Briefly Rear view display ON/OFF* R (reverse) More than Help lines indica- 3 seconds tion ON/OFF Except Briefly Auto-dimming R (reverse) function ON/OFF* 3 to 6 Electronic com- seconds pass display ON/...
Page 168 The mirror has a photosensor attached on both the front and back sides. Use care not to cover the sensors with stickers, or other similar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator. NOTE When cleaning the mirror, use a paper towel or similar item dampened with...
Page 169: Type C Inside Mirror (If Equipped)
3-40 Instruments and controls & Type C inside mirror (if equipped) Left button Auto dimming indicator Photosensor Right button This mirror has an anti-glare feature which automatically reduces glare coming from headlights of vehicles behind you. It also contains a built-in compass. .
Page 170: Outside Mirrors
! Compass zone adjustment 1. The zone setting is factory preset to Zone 8. Refer to the “Compass calibration zone” map attached to the end of this manual to verify that the compass zone setting is correct for your geographical location.
Page 171 3-42 Instruments and controls ! Outside mirror defogger The outside mirror defogger shares the control switch with the rear window de- fogger. Therefore, the outside mirror de- fogger always operates with the rear window defogger. If the rear window defogger is set to the continuous operation mode, the outside mirror defogger also follows the contin- uous setting.
Page 172: Tilt Steering Wheel
Tilt steering wheel WARNING Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury. 1. Adjust the seat position. Refer to “Front seats” F1-2. 2. Pull the tilt lock lever down. 3.
Page 173 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 174 Ventilator... Airflow ... Ventilator ... Automatic climate control system ... Control panel ... Rear air conditioner... Temperature sensors... Operating tips for heater and air conditioner... 4-10 Cleaning ventilator grille... Efficient cooling after parking in direct sunlight ... Lubrication oil circulation in the refrigerant circuit...
Page 175: Climate Control
Climate control Ventilator & Airflow Ventilator and airflow : Standard : If equipped...
Page 176 Climate control ! Airflow mode selection *: If equipped – CONTINUED –...
Page 177: Ventilator
Climate control & Ventilator ! Center ventilators Move the tab to adjust the flow direction. ! Side ventilators Open Close Move the tab to adjust the flow direction. To open the ventilator, turn the side grille open/close wheel upward. To close it, turn the wheel downward. ! Rear ventilators Move the tab or rotate it to adjust the flow direction.
Page 178: Automatic Climate Control System
Automatic climate control system NOTE . Operate the automatic climate con- trol system when the engine is running. . The blower fan rotates at a low speed when the engine coolant tem- perature is low. For efficient defogging or dehumidify- ing in cold weather, press the “A/C”...
Page 179 Climate control ! OFF button The Automatic Climate Control system turns off (the air conditioner compressor and fan turn off) when the “OFF” button is pressed. When the “OFF” button is pressed, the outside air introduction mode (air inlet selection OFF) is automatically selected. ! Temperature control dial Driver’s side Passenger’s side...
Page 180 – Defroster button To defrost or dehumidify the windshield and front door windows, push the defros- ter button “ ”. When the “ ” button is pushed, the indicator light on the button illuminates and the following operation is performed. .
Page 181 Climate control ! Airflow mode selection button Select the desired airflow mode by push- ing the airflow mode selection button. The selected airflow mode is shown on the center of the dial. There are five airflow modes that activate the following air outlets. (Ventilation): Instrument panel outlets (Bi-level): Instrument panel outlets and foot outlets...
Page 182: Rear Air Conditioner
& Rear air conditioner The rear air conditioner blows cool air out of the rear ventilators while the “A/C” button on the control panel is in the “ON” position. The fan speed of the rear air conditioner can be adjusted using the rear air conditioner dial behind the center console.
Page 183: Operating Tips For Heater And Air Conditioner
HFC134a. Therefore, the meth- od of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
Page 184: Air Filtration System
Under extremely dusty conditions, the filter should be replaced more fre- quently. It is recommended that you have your filter checked or replaced by your SUBARU dealer. For replacement, we recommend the use of a genuine SUBARU air filter kit. Replacement schedule:...
Page 185 4-12 Climate control 4. Remove the air filter cover by detach- ing the five clips. 5. Unhook the air filter and draw it out. 6. Replace the air filter with a new one. 7. Install the air filter cover. 8. Install the glove box. 9.
Page 186 CAUTION Contact your SUBARU dealer if the following occurs, even if it is not yet time to change the filter. – Reduction of the airflow through the vents. – Windshield gets easily fogged or misted. NOTE The filter can influence the air condi- tioning, heating and defroster perfor- mance if not properly maintained.
Page 187 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 188: Audio
Antenna system ... Printed antenna... FM reception ... Installation of accessories... Audio set ... Type A audio set ... Type B audio set ... Type A audio set (if equipped) ... Radio operation... Compact disc player operation ... Type B audio set (if equipped)... Radio operation ...
Page 189: Antenna System
This noise does not indicate a radio malfunction. Installation of accessories Always consult your SUBARU dealer before installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic...
Page 190: Audio Set
Audio set Your SUBARU may be equipped with one of the following audio sets. See the pages indicated in this section for operating details. & Type A audio set . Radio operation: refer to page 5-4 . CD (compact disc) player operation: refer to page 5-10 &...
Page 191: Type A Audio Set (If Equipped)
Audio Type A audio set (if equipped) The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. & Radio operation (1) Satellite radio mode button (2) FM AM mode button (3) Auxiliary audio unit and Rear seat entertainment selection button (4) Tuning button (5) AUDIO button...
Page 192 Audio ! To change tone and balance control modes Each brief press of the “TONE BAL” button (9) changes control modes in the following sequence starting from volume control mode. (When the radio is first turned on, the control mode is in the volume control.) The “TONE BAL”...
Page 193 Audio Control mode (range of le- vels) Turn counterclockwise Bass control (−6 to +6) For less bass sound Midrange control (−6 to +6) For less midrange sound Treble control (−6 to +6) For less treble sound Fader control (R9 to F9) To increase rear speaker vo- lume and decrease front speak- er volume...
Page 194 ! Satellite radio mode (if equipped) To receive satellite radio, it is necessary to install the SUBARU genuine satellite receiver (optional part) and to enter into a contract with a satellite radio network service such as “XM satellite radio”...
Page 195 Audio ! XM satellite radio (for U.S.A. only) is a continental U.S. based satellite radio service, including music, news, sports, talk and children’s programming. provides digital quality audio and text information, including song title and artist name. A service fee is required to receive the XM service.
Page 196 for more than 1.5 seconds to store the channel. If the button is pressed for less than 1.5 seconds, the preceding selection will remain in memory. NOTE If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio re- moval, all channels stored in the preset buttons are cleared.
Page 197: Compact Disc Player Operation
5-10 Audio & Compact disc player operation (1) CD button (2) Track button (3) AUDIO button (4) Seek and Folder button (5) Random button (6) Repeat button (7) Scan button (8) Eject button ! To playback a compact disc ! When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side...
Page 198 . If you insert a disc that cannot be played by the player, “CHECK DISC” will appear on the display and the player will revert to the previously selected mode. . The player is designed to be able to play music CD-Rs and music CD-RWs, but it may not be able to play certain ones.
Page 199 5-12 Audio ! Repeating ! To repeat the currently playing track/ file (track) To repeat a track/file (track), briefly press the “RPT” button (6) while the track/file (track) is playing. The display will show “RPT”, and the track/file (track) will be repeated.
Page 200 NOTE Random playback will be cancelled if you perform any of the following steps. . Press the “RPT” button . Press the “SCAN” button . Press the “ ” button . Select the radio mode . Press the “RSE AUX” button .
Page 201 5-14 Audio . If the disc is left ejected for more than approximately 15 seconds after the ignition switch is turned to the “LOCK” position, a disc protection function will operate, automatically reloading the disc. In this case, the disc is not played. ! Display selection (MP3 disc) If you press the “AUDIO”...
Page 202: Type B Audio Set (If Equipped)
Type B audio set (if equipped) The audio set will operate only when the ignition switch is in the “Acc” or “ON” positions. & Radio operation 5-15 Audio (1) Satellite radio mode button (2) FM AM mode button (3) Auxiliary audio unit and Rear seat entertainment selection button (4) Tuning button (5) AUDIO button...
Page 203 5-16 Audio ! To change tone and balance control modes Each brief press of the “TONE BAL” button (9) changes control modes in the following sequence starting from volume control mode. (When the radio is first turned on, the control mode is in the volume control.) The “TONE BAL”...
Page 204 Control mode (Range of le- vels) Turn counterclockwise Bass control (−6 to +6) For less bass sound Midrange control (−6 to +6) For less midrange sound Treble control (−6 to +6) For less treble sound Fader control (R9 to F9) To increase rear speaker vo- lume and decrease front speaker volume...
Page 205 ! Satellite radio mode (if equipped) To receive satellite radio, it is necessary to install the SUBARU genuine satellite receiver (optional part) and to enter into a contract with a satellite radio network service such as “XM satellite radio”...
Page 206 ! XM satellite radio (for U.S.A. only) is a continental U.S. based satellite radio service, including music, news, sports, talk and children’s programming. provides digital quality audio and text information, including song title and artist name. A service fee is required to receive the XM service.
Page 207 5-20 Audio for more than 1.5 seconds to store the channel. If the button is pressed for less than 1.5 seconds, the preceding selection will remain in memory. NOTE If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio re- moval, all channels stored in the preset buttons are cleared.
Page 208: Built In Cd Changer Operation
& Built in CD changer operation 5-21 Audio (1) CD button (2) Track button (3) AUDIO button (4) Seek and Folder button (5) Random button (6) Repeat button (7) Scan button (8) Eject button (9) Disc select button (10) Load button NOTE .
Page 209 5-22 Audio ! How to insert a CD(s) ! Inserting a CD 1. Briefly press the “LOAD” button (10). If the magazine in the player has an idle position where you can insert a disc, the disc number indicator associated with the idle position will blink.
Page 210 ! When there are CDs loaded: Press a desired one of the disc select buttons (9) the disc number indicator of which steadily lights up. The player will then start playback of the selected CD, beginning with the first track. If a disc that the player cannot read has been loaded, “CHECK DISC”...
Page 211 5-24 Audio – Press the disc select button – Select the radio mode – Press the “RSE AUX” button – Press the “ ” or “ ” side of the “SEEK FLDR” button (MP3 disc) – Turn off the power of the audio equipment –...
Page 212 next one in the following sequence. If you accidentally press the button and cancel the random mode, press it again to reselect the random mode. . Random playback will be cancelled if you perform any of the following steps. – Press the “RPT” button –...
Page 213: Audio Control Buttons
5-26 Audio ! How to unload CDs from the player ! Ejecting a CD from the player Of the discs loaded, you can select and remove only one disc. 1. Use the disc select button (9) to select the disc to be ejected. 2.
Page 214 The audio display will show “MUTE”. If you press the button again, the original sound volume will return and “MUTE” turns off. NOTE If your vehicle is equipped with a genuine SUBARU navigation system, the display will show “ ”.
Page 215: Auxiliary Input Jack
5-28 Audio Auxiliary input jack By connecting a commercial audio pro- duct to the vehicle, such as a portable audio player, you can hear its sound via the vehicle’s speaker. An auxiliary (AUX) input jack is equipped in the lower compartment of the center console.
Page 216: Rear Seat Entertainment (Rse) System
Rear Seat Entertainment (RSE) system operation (if equipped) If your vehicle is equipped with the Rear Seat Entertainment (RSE) system, you can listen to the audio via the vehicle speakers. Push the “RSE AUX” button to play a DVD using the Rear Seat Entertain- ment system.
Page 217 5-30 Audio . You cannot use a DualDisc in the CD player. If you insert a DualDisc into the player, the disc may not come out again, possibly causing the player to malfunction. . In cold and/or rainy weather, dew can form inside the CD player, preventing normal operation.
Page 218 Interior light ... Dome light ... Cargo area light ... Rear gate light ... Map light... Automatic ambient light for center console area (if equipped)... Sun visors ... Sun visor extension plate ... Vanity mirror with light ... Storage compartment ... Glove box ...
Page 219: Interior Equipment
. All doors and the rear gate are locked using the remote keyless entry transmitter. The setting of the period for which the light remains on (OFF delay timer) can be changed by a SUBARU dealer. Contact the nearest SUBARU dealer for details.
Page 220: Cargo Area Light
. Any of the doors or the rear gate is opened. – The operational/non-operational setting of this function can be changed by a SUBARU dealer. Contact your SUBARU dealer to change the setting. – The factory setting (default setting) for this function is set as “operational”...
Page 221: Automatic Ambient Light For Center Console Area (If Equipped)
The setting of the period for which the light remains illuminated (OFF delay timer) can be changed by a SUBARU dealer. Con- tact your SUBARU dealer for details. NOTE If any of the doors or the rear gate is not completely closed, the map lights will remain illuminated as a result.
Page 222: Sun Visor Extension Plate
& Sun visor extension plate With the sun visor positioned over the side window, you can use the sun visor extension plate to prevent glare through the gap between the sun visor and center pillar. To use the extension plate, pull it toward the rear of the vehicle.
Page 223: Storage Compartment
Interior equipment Storage compartment CAUTION . Always keep the storage com- partment closed while driving to reduce the risk of injury in the event of sudden stops or an accident. . Do not store spray cans, contain- ers with flammable or corrosive liquids or any other dangerous items in the storage compart- ment.
Page 224: Rear Console
! Upper compartment Upper compartment lock release Pull up the upper compartment lock release to open the upper compartment. ! Lower compartment Lower compartment lock release Pull up the lower compartment lock release to open the lower compartment. Interior equipment &...
Page 225: Overhead Console
Interior equipment & Overhead console To open the console, push on the lid lightly and it will automatically open. CAUTION When your vehicle is parked in the sun or on a warm day, the inside of the overhead console heats up. Avoid storing plastic or other heat- vulnerable or flammable articles such as a lighter in the overhead...
Page 226: Second-Row Seat Cup Holders
& Second-row seat cup holders A dual cup holder is built in the armrest. CAUTION When a cup containing a beverage is in the cup holder, do not slide or recline any seat. Otherwise, the beverage could spill while driving and, if the beverage is hot, it could scald you.
Page 227: Accessory Power Outlets
6-10 Interior equipment trim can be used to hold beverage bottles and other items. Accessory power outlets Power outlets in the center console Power outlets in the rear cabin Accessory power outlets are provided in the center console (lower compartment) and in the rear cabin.
Page 228 especially metal ones such as coins or aluminum foil, into the accessory power outlet. That could cause a short circuit. Al- ways put the cap on the acces- sory power outlet when it is not in use. . Use only electrical appliances which are designed for 12V DC.
Page 229: Coat Hook
6-12 Interior equipment compartment) and the lid. It is also possible to pass the cord through a groove in the lid and up to the center console (upper compartment). Coat hook A coat hook is attached to each hand grip for the outboard second-row passenger’s seats.
Page 230: Shopping Bag Hook
Shopping bag hook CAUTION Do not hang items on the shopping bag hook that weigh 11 lbs (5 kg) or more. A shopping bag hook is attached to each side of the cargo area. Floor mat A retaining pin is located on the driver’s side of the vehicle next to the fuel filler door release.
Page 231: Cargo Area Cover (If Equipped)
6-14 Interior equipment Cargo area cover (if equipped) The cargo area cover is provided for covering the cargo area and to protect its contents from direct sunlight. This cover is detachable to make room for additional cargo. & Using the cover Holder Insert the seatbelt webbing to the holder of the third-row seat.
Page 232: To Remove The Cover
& To remove the cover 1. Rewind the cover. 2. Pull either sleeve on the end of the cover housing to shorten the cover’s length. 3. Take it off the retainer. & To install the cover housing 1. Remove the cover at the cover hous- ing retaining part using a flat-head screw- driver.
Page 233: Convenient Tie-Down Hooks
6-16 Interior equipment Convenient tie-down hooks CAUTION The convenient tie-down hooks are designed only for securing light cargo. Never try to secure cargo that exceeds the capacity of the hooks. The maximum load capacity is 44 lbs (20 kg) per hook. The cargo area is equipped with four tie- down hooks so that cargo can be secured with a luggage net or ropes.
Page 234: Homelink Wireless Control System (If Equipped)
® HomeLink Wireless Control System (if equipped) ® HomeLink buttons Indicator light Hand-held transmitter* * Not part of your vehicle’s remote keyless entry system but of a ® HomeLink -compatible device. ® The HomeLink Wireless Control System, located on the driver’s sun visor, is a handy way to operate, from inside of your vehicle, up to three remote-controlled indoor and outdoor devices, such as...
Page 235: Garage Door Opener Programming In The U.s.a
6-18 Interior equipment NOTE . After programming your HomeLink Wireless Control System for the de- sired devices, retain the hand-held transmitters for further programming or device testing in the event of a problem. . It is recommended that you insert a new battery in the hand-held transmit- ter of a device to ensure correct programming.
Page 236: Programming Rolling-Code-Protected Garage Door Openers In The U.s.a
your garage door opener may be pro- tected by a rolling code feature. In this case you need to perform additional steps. Refer to “Programming rolling-code-pro- tected garage door openers in the U.S.A.” F6-19. NOTE Rolling-code-protected garage door openers are manufactured after 1996. See the instruction manual of your garage opener for confirmation.
Page 237: Programming For Entrance Gates And Garage Door Openers In Canada
6-20 Interior equipment trol System and your garage door opener should activate when the HomeLink button is pressed. & Programming for entrance gates and garage door open- ers in Canada 1. Unplug the motor of the entrance gate or garage door opener from the outlet. 2.
Page 238: Erasing Homelink
3. Press and hold the hand-held trans- ® mitter button. The HomeLink indicator light will flash, first slowly and then rapidly. 4. When the indicator light begins to flash rapidly, release both buttons. The programming for the previous device is now erased and the new device can be operated by pushing the HomeLink button.
Page 239 . Do not disassemble or modify the camera, switch or wiring. If smoke comes out or you smell a strange odor, stop using the rear view camera immediately. Contact your SUBARU dealer for an inspection. Continued use may result in accident, fire or electric shock. CAUTION .
Page 240: Viewing Range On The Screen
NOTE . The image of the rear view camera has priority over other screen displays. . The image of the rear view camera is horizontally reversed as is the case with the vehicle rearview mirror or the side view mirror. .
Page 241: Help Line
6-24 Interior equipment Range of view Image from camera The area above the camera cannot be viewed. If there is an object that has a wide projection on its upper part such as a sign pole behind the vehicle, the projec- tion cannot be seen on the screen.
Page 242 ferent from the indication of the help lines. . Differences may occur due to number of passengers or loaded cargo. . When the vehicle is on a slope or when the vehicle is inclined against the road, the indication is different from the actual posi- tion.
Page 243 6-26 Interior equipment ! Feature of distance marker 3 feet (1 m) line 6.5 feet (2 m) line 10 feet (3 m) line The distance marker shows the distance on the road. If there is a car or other object close behind, distance cannot be correctly displayed.
Page 244: Starting And Operating
Fuel ... Fuel requirements ... Fuel filler lid and cap... State emission testing (U.S. only)... Preparing to drive ... Starting the engine... Stopping the engine... Remote engine start system (dealer option) ... Starting your vehicle ... Remote start safety features ... Entering the vehicle while it is running via remote start...
Page 245: Starting And Operating
Do not be concerned if your vehicle sometimes knocks lightly when you drive up a hill or when you accelerate. Contact your SUBARU dealer if you use a fuel with the specified octane rating and your vehicle knocks heavily or persistently.
Page 246: Fuel Filler Lid And Cap
SUBARU. In addition, some gasoline suppliers are now producing reformulated gasolines, which are designed to reduce vehicle emissions. SUBARU approves the use of reformulated gasoline. If you are not sure what the fuel contains, you should ask your service station...
Page 247 Starting and operating WARNING Before opening the fuel filler cap, first touch the vehicle body or a metal portion of the fuel pump or similar object to discharge any static electricity that may be present on your body. If your body is carry- ing an electrostatic charge, there is a possibility that an electric spark could ignite the fuel, which could...
Page 248: State Emission Testing (U.s. Only)
Paint damage caused by spilled fuel is not covered under the SUBARU Limited Warranty. . Always use a genuine SUBARU fuel filler cap. If you use the wrong cap, it may not fit, and your fuel tank and emission con- trol system may be damaged.
Page 249 There are some states that use four-wheel dynamometers in their testing programs. When properly used, that equipment will not damage a SUBARU AWD vehicle. Under no circumstances should the rear wheels be jacked off the ground, nor should the driveshaft be disconnected for state emission testing.
Page 250: Preparing To Drive
“START” position without depressing the accelerator pedal. (4) If the engine still refuses to start, contact your nearest SUBARU dealer for assistance. 6. Confirm that all warning and indicator lights have turned off after the engine has...
Page 251: Stopping The Engine
Starting and operating started. The fuel injection system auto- matically lowers the idle speed as the engine warms up. While the engine is warming up, make sure that the select lever is at the “P” or “N” position and that the parking brake is applied.
Page 252: Starting Your Vehicle
& Starting your vehicle The remote engine start system is acti- vated by pressing the “ ” button twice within 3 seconds on your remote engine start transmitter. The system will check certain pre-conditions before starting, and if all safety parameters are correct, the engine will start within 5 seconds.
Page 253: Pre-Heating Or Pre-Cooling The Interior Of The Vehicle
7-10 Starting and operating transmitter within a few seconds immedi- ately following remote engine start shut- down. & Pre-heating or pre-cooling the interior of the vehicle Before exiting the vehicle, set the tem- perature controls to the desired setting and operation. After the system starts the vehicle, the heater or air-conditioning will activate and heat or cool the interior to your setting.
Page 254: System Maintenance
sing the brake pedal repeatedly will toggle the feature ON or OFF each time. 7. To exit the remote transmitter and feature programming mode, turn the igni- tion switch to the “LOCK” position, remove the key from the ignition switch and test operation of the remote transmitter(s) and horn confirmation feature.
Page 255: Automatic Transmission
7-12 Starting and operating 2. Remove the circuit board from the bottom half of the case and slide the white plastic battery holder out from under the battery tab releasing the batteries. Re- move the old batteries and replace with new ones.
Page 256: Select Lever
“R” position or vice versa until the vehicle has completely stopped. Such shifting may cause damage to the transmis- sion. . When parking the vehicle, first securely apply the parking brake and then place the select lever in the “P” position. Avoid parking for a long time with the select lever in any other position as doing so could result in a dead...
Page 257: Shift Lock Function
7-14 Starting and operating is started. If the select lever does not move from the “P” position with the brake pedal de- pressed, the select lever button pushed in, and the ignition switch in the ON position, refer to “Shift lock function” F7- ! R (Reverse) This position is for backing the vehicle.
Page 258 If you must perform the above procedure, the shift lock system (or the vehicle control system) may be malfunctioning. Contact a SUBARU dealer for an inspection as soon as possible. If the select lever does not move after performing the above procedure, refer to “Shift lock release using the shift lock...
Page 259: Selection Of Manual Mode
If the select lever does not move after performing the above procedure, the shift lock system may be malfunctioning. Con- tact a SUBARU dealer for an inspection as soon as possible. & Selection of manual mode With the vehicle either moving or station- ary, move the select lever from the “D”...
Page 260: Driving Tips
Gearshifts can be performed using the select lever. Shift to the next-higher gear by briefly pushing the select lever toward the “+” end of the manual gate. Shift to the next-lower gear by briefly pulling the select lever toward the “−” end of the manual gate.
Page 261: Sport Mode
7-18 Starting and operating & SPORT mode SPORT mode is used when power is needed for rapid acceleration or for uphill driving. To select this mode, move the select lever from the “D” position to the manual gate. When selected, the SPORT mode indica- tor light on the combination meter will illuminate.
Page 262: Braking
Braking & Braking tips WARNING Never rest your foot on the brake pedal while driving. This can cause dangerous overheating of the brakes and needless wear on the brake pads and linings. ! When the brakes get wet When driving in rain or after washing the vehicle, the brakes may get wet.
Page 263: Disc Brake Pad Wear Warning Indicators
If a squeaking or scraping noise is heard from the disc brakes while braking, im- mediately have your vehicle inspected by the nearest SUBARU dealer. ABS (Anti-lock Brake Sys- tem) WARNING Always use the utmost care in driving –...
Page 264: Abs System Self-Check
. The warning light illuminates dur- ing driving. If these occur, have the ABS system repaired at the first available oppor- tunity by your SUBARU dealer. NOTE If the warning light behavior is as described in the following, the ABS system may be considered normal.
Page 265: Electronic Brake Force Distribution (Ebd) System
7-22 Starting and operating started, the ABS warning light may illumi- nate. This is due to the low battery voltage and does not indicate a malfunction. When the battery becomes fully charged, the light will turn off. Electronic Brake Force Dis- tribution (EBD) system The EBD system maximizes the effective- ness of the brakes by allowing the rear...
Page 266: Vehicle Dynamics Control System
3. Release the parking brake. If both warning lights turn off, the EBD system may be malfunctioning. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights illuminate again and remain illuminated after the engine...
Page 267 Vehicle Dynamics Control system, have an inspection of that system performed by an authorized SUBARU dealer. . The following precautions should be observed in order to ensure that the Vehicle Dynamics Con- trol system is operating properly.
Page 268: Vehicle Dynamics Control System Monitor
The following two situations could indicate a malfunction of the Vehicle Dynamics Control system; if either should occur, have an authorized SUBARU dealer carry out an inspection of that system at the first available opportunity. . The indicator light does not illuminate...
Page 269 Vehicle Dynamics Control system; if any should occur, we recommend that you have an authorized SUBARU dealer carry out an inspection of the system at the first available opportu- nity. . The warning light does not illuminate when the ignition key is turned to the ON position.
Page 270: Traction Control System Off Switch
to heat up sufficiently. & Traction Control system OFF switch Pressing the switch to deactivate the Traction Control system can facilitate the following operations. . a standing start on a steeply sloping road with a snowy, gravel-covered, or otherwise slippery surface .
Page 271: Tire Pressure Monitoring System (Tpms)
This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. Do not inject any tire liquid or...
Page 272: Parking Your Vehicle
CAUTION Do not place metal film or any metal parts under the driver’s seat. This may cause poor reception of the signals from the tire pressure sen- sors, and the tire pressure monitor- ing system will not function prop- erly. NOTE This device complies with Part 15 of the FCC Rules and with RSS-210 of...
Page 273: Parking Tips
7-30 Starting and operating To release the parking brake, hold down the brake pedal while depressing the parking brake pedal and slowly releasing When the parking brake is set while the engine is running, the brake system warning light illuminates. After starting the vehicle, be sure that the warning light has turned off before the vehicle is driven.
Page 274: To Set Cruise Control
. towing a trailer & To set cruise control 1. Push the main switch button. The cruise control indicator light on the combination meter will illuminate. 2. Depress the accelerator pedal until the vehicle reaches the desired speed. 3. Push the control lever downward in the “SET/COAST”...
Page 275: To Turn Off The Cruise Control
7-32 Starting and operating . Depress the brake pedal. . Shift the select lever into the “N” position. The cruise control set indicator light on the combination meter turns off when the cruise control is canceled. To resume the cruise control after it has been temporarily canceled and with vehi- cle speed of approximately 20 mph (32 km/h) or more, push the control lever...
Page 276: Cruise Control Indicator Light
! To decrease the speed (by control lever) Push the control lever downward in the “SET/COAST” direction and hold it until the vehicle reaches the desired speed. Then, release the control lever. The vehicle speed at that moment will be memorized and treated as the new set speed.
Page 277 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 278 New vehicle break-in driving – the first 1,000 miles (1,600 km) ... Fuel economy hints ... Engine exhaust gas (carbon monoxide)... Catalytic converter ... Periodic inspections ... Driving in foreign countries ... Driving tips for AWD models... On-pavement and off road driving... Winter driving ...
Page 279: Driving Tips
Driving tips New vehicle break-in driving – the first 1,000 miles (1,600 The performance and long life of your vehicle are dependent on how you handle and care for your vehicle while it is new. Follow these instructions during the first 1,000 miles (1,600 km): .
Page 280: Catalytic Converter
(misfiring, back- firing or incomplete combustion), have your vehicle checked and repaired by an authorized SUBARU dealer. . Do not apply undercoating or rust prevention treatment to the heat shield of catalytic converter and the exhaust sys- tem.
Page 281: Periodic Inspections
Driving tips Periodic inspections To keep your vehicle in the best condition at all times, always have the recom- mended maintenance services listed in the maintenance schedule in the “War- ranty and Maintenance Booklet” per- formed at the specified time or mileage intervals.
Page 282: On-Pavement And Off Road Driving
By shifting power between the front and rear wheels, SUBARU AWD can also provide added traction during accelera- tion, and added engine braking force during deceleration.
Page 283 If you do take your SUBARU off-road, certain common sense precautions such as those in the following list should be taken. . Make certain that you and all of your passengers are wearing seatbelts.
Page 284: Winter Driving
“Warranty and Mainte- nance Booklet”. Remember that damage done to your SUBARU while operating it off-road and not using common sense precautions such as those listed above is not eligible for warranty coverage.
Page 285 Do not use engine antifreeze or other substitutes because they may damage the paint of the vehicle. SUBARU Windshield Washer Fluid con- tains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing tem- perature varies according to how much it is diluted, as indicated in the following table.
Page 286: Driving On Snowy And Icy Roads
If your SUBARU is not going to be used for an extended period, it is best to have the fuel tank filled to capacity.
Page 287: Corrosion Protection
8-10 Driving tips Snow stuck on the wiper arm prevents the wiper from working effectively. If snow is stuck on the wiper arm, pull off the road to a safe place, then remove it. If you stop the vehicle at road side, use the hazard warning flasher to alert other drivers.
Page 288: Tire Chains
Recommended winter (snow) tire size P255/55R18 stud less & Tire chains CAUTION Tire chains cannot be used on your vehicle because of the lack of clearance between the tires and vehicle body. & Rocking the vehicle If you must rock the vehicle to free it from snow, sand, or mud, depress the accel- erator pedal slightly and move the select lever back and forth between “D”...
Page 289: Vehicle Capacity Weight
8-12 Driving tips CAUTION Do not carry spray cans, containers with flammable or corrosive liquids or any other dangerous items inside the vehicle. NOTE For better fuel economy, do not carry unneeded cargo. & Vehicle capacity weight The load capacity of your vehicle is determined by weight, not by available cargo space.
Page 290: Roof Rails And Crossbar (If Equipped)
adjusted by relocating luggage inside the vehicle. Even if the total weight of your luggage is lower than the vehicle capacity weight, either front or rear GAW may exceed the GAWR, depending on the distribution of the luggage. When possible, the load should be evenly distributed throughout the vehicle.
Page 291 8-14 Driving tips ! Installing carrying attachments on the crossbars When installing any carrying attachment such as a bike carrier, ski carrier, kayak carrier, cargo basket, etc. on the cross- bars, follow the manufacturer’s instruc- tions and make sure that the attachment is securely fixed to the crossbars.
Page 292 3. The crossbar with a 150 lbs (68 kg) load label attached onto it is the front crossbar. An arrow is marked on the back of the front crossbar for correct installa- tion. Install the front crossbar so that the arrow faces the front of the vehicle.
Page 293: Roof Molding And Crossbar (If Equipped)
8-16 Driving tips 6. Adjust the alignment of the crossbar on the roof rails, and if available, use a T- ® 30 torx bit and torque wrench and tighten ® the T-30 torx head screws to 30 to 35 lbf·in (3.4 to 4.0 N·m, 0.35 to 0.41 kgf·m) of torque (or tighten securely with the torx wrench provided).
Page 294 road hazard due to loss of cargo could result. . When using the roof crossbar kit, make sure that the total weight of the crossbars, carrying attach- ment and cargo does not exceed the maximum load limit. Over- loading may cause damage to the vehicle and create a safety hazard.
Page 295: Trailer Hitch (If Equipped)
8-18 Driving tips Trailer hitch (if equipped) Trailer hitch WARNING . Never exceed the maximum weight specified for the trailer hitch. Exceeding the maximum weight could cause an accident resulting in serious personal in- juries. Permissible trailer weight changes depending on the situa- tion.
Page 296 3. Insert the safety pin into the hitch pin securely. 4. Pull the ball mount to make sure it does not come off the hitch receiver. Hitch ball installation point Hooks for safety chains 5. Use only a hitch ball that is appropriate for the ball mount and your trailer.
Page 297: When You Do Not Tow A Trailer
Seek the advice of your SUBARU dealer to assist you in purchasing a hitch and other necessary towing equipment appropriate for your vehicle. In addition, be sure to follow the...
Page 298 ble. ! Total trailer weight Total trailer weight The total trailer weight (trailer weight plus its cargo load) must never exceed the maximum weight shown in the following table. Vehicle without cooling kit Conditions When towing a trailer without brakes. When towing a trailer with brakes.
Page 299 8-22 Driving tips ! Gross Vehicle Weight (GVW) and Gross Vehicle Weight Rating (GVWR) Gross Vehicle Weight The Gross Vehicle Weight (GVW) must never exceed the Gross Vehicle Weight Rating (GVWR). Gross Vehicle Weight (GVW) is the combined total of the weight of the vehicle, driver, passengers, luggage, trailer hitch, trailer tongue load and any other optional equipment installed on your vehicle.
Page 300: Trailer Hitches
! Tongue load Tongue load WARNING If the trailer is loaded with more weight in the back of trailer’s axle than in the front, the load is taken off the rear axle of the towing vehicle. This may cause the rear wheels to skid, especially during braking or when vehicle speed is reduced dur- ing cornering, resulting in over-...
Page 301: Connecting A Trailer
Choose a proper hitch for your vehicle and trailer. The use of a genuine SUBARU trailer hitch is recommended. A genuine SUBARU hitch is available from your SUBARU dealer. If use of a non-genuine hitch is unavoid- able, be sure the hitch is suited to your vehicle and trailer.
Page 302 To ensure the trailer lights are connected properly, please consult your SUBARU dealer. Check for proper operation of the turn signals, the brake lights and parking lights each time you hitch up.
Page 303: Trailer Towing Tips
8-26 Driving tips & Trailer towing tips CAUTION . Never exceed 45 mph (72 km/h) when towing a trailer in hilly country on hot days. . When towing a trailer, steering, stability, stopping distance and braking performance will be dif- ferent from normal operation.
Page 304 . If the ABS warning light illuminates while the vehicle is in motion, stop towing the trailer and have repairs performed immediately by the nearest SUBARU dealer. ! Driving on grades . Before going down a steep hill, slow...
Page 305 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 306: In Case Of Emergency
If you park your vehicle in an emergency... Spare tire ... Removing the spare tire ... Re-storage of spare tire ... Temporary spare tire... Flat tires... Changing a flat tire... Tire pressure monitoring system (TPMS) ... Jump starting ... How to jump start... In case of emergency Engine overheating ...
Page 307: If You Park Your Vehicle In An Emergency
In case of emergency If you park your vehicle in an emergency The hazard warning flasher should be used in day or night to warn other drivers when you have to park your vehicle under emergency conditions. Avoid stopping on the road. It is best to safely pull off the road if a problem occurs.
Page 308: Removing The Spare Tire
carefully read “Temporary spare tire” F9-5 for instructions and precautions. & Removing the spare tire 1. Take the wheel nut wrench and exten- sion out of the tool bag. Refer to “Main- tenance tools” F9-19. 2. Remove the subfloor storage lid in the cargo area.
Page 309: Re-Storage Of Spare Tire
In case of emergency and pull it through the center of the temporary spare tire. 9. After the temporary spare tire is removed from the cable, the cable must be wound up completely by turning the hoist nut shaft clockwise until you hear a clicking sound.
Page 310: Temporary Spare Tire
This indicates the tire pressure monitoring system (TPMS) is un- able to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. – CONTINUED –...
Page 311: Flat Tires
In case of emergency CAUTION Never use any temporary spare tire other than the original. Using other sizes may result in severe mechan- ical damage to the drive train of your vehicle. The temporary spare tire is smaller and lighter than a conventional tire and is designed for emergency use only.
Page 312 . Always turn off the engine before raising the flat tire off the ground using the jack. Never swing or push the vehicle supported with the jack. The jack can come out of the jacking point due to a jolt and this can result in a severe accident.
Page 313 In case of emergency 8. Loosen the wheel nuts using the wheel nut wrench but do not remove the nuts. 9. Place the jack under the side sill at the front or rear jack-up point closest to the flat tire. Turn the jackscrew by hand until the jack head engages firmly into the jack-up point.
Page 314 WARNING Do not use oil or grease on the wheel studs or nuts when the spare tire is installed. This could cause the nuts to become loose and lead to an accident. 15. Turn the jack handle counterclockwise to lower the vehicle. CAUTION There are 2 types of wheel nut wrenches that apply to different...
Page 315: Tire Pressure Monitoring System (Tpms)
9-10 In case of emergency holder. Refer to “Spare tire” F9-2 for its location, instructions and precautions. CAUTION . When stowing a flat tire in the spare tire holder, turn the hoist shaft end only slowly. If it is turned quickly, the wheel disc of the flat tire could be damaged.
Page 316: Jump Starting
SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors. If the light illuminates steadily after...
Page 317: How To Jump Start
9-12 In case of emergency & How to jump start 1. Make sure the booster battery is 12 volts and the negative terminal is grounded. 2. If the booster battery is in another vehicle, do not let the two vehicles touch. 3.
Page 318 9-13 In case of emergency (1) Connect one jumper cable to the positive (+) terminal on the discharged battery. (2) Connect the other end of the jumper cable to the positive (+) term- inal of the booster battery. (3) Connect one end of the other cable to the negative (−) terminal of the booster battery.
Page 319: Engine Overheating
This will cause the vehicle to spin away due to the operation or deterioration of the center differential. If towing is necessary, it is best done by your SUBARU dealer or a commercial towing service. Observe the following procedures for safety.
Page 320: Towing And Tie-Down Hooks
& Towing and tie-down hooks The towing hooks should be used only in an emergency (e.g., to free a stuck vehicle from mud, sand or snow). CAUTION . Use only the specified towing hooks and tie-down hooks. Never use suspension parts or other parts of the body for towing or tie-down purposes.
Page 321 9-16 In case of emergency After towing, remove the towing hook from the vehicle and stow it in the tool bag. Fit the towing hook cover on the bumper. WARNING . Do not use the towing hook except when towing your vehicle. .
Page 322: Using A Flat-Bed Truck
The front tie-down hooks are located between each of the front tires and the front bumper. Rear tie-down hooks: The rear tie-down hooks are located near each of the jack-up reinforcements. WARNING Use the rear tie-down hooks only for downward anchoring. If they are used to anchor the vehicle in any other direction, cables may slip off the hooks, possibly causing a dan-...
Page 323: Rear Gate - If The Rear Gate Cannot Be Unlocked
9-18 In case of emergency CAUTION . If transmission failure occurs, transport your vehicle on a flat- bed truck. . Do not run the engine while being towed using this method. Trans- mission damage could result if the vehicle is towed with the engine running.
Page 324: Maintenance Tools
Maintenance tools Your vehicle is equipped with the following maintenance tools. Screwdriver Towing hook (eye bolt) (if equipped) Wheel nut wrench Extension & Jack and jack handle The jack and jack handle is stored under the cargo area. For how to use the jack, refer to “Flat tires” F9-6.
Page 325 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 326: Appearance Care
Exterior care ... 10-2 Washing... Waxing and polishing ... Cleaning aluminum wheels ... Corrosion protection... 10-4 Most common causes of corrosion ... To help prevent corrosion... Cleaning the interior... 10-2 Seat fabric ... 10-3 Leather seat materials... 10-3 Synthetic leather upholstery... Climate control panel, audio panel, instrument panel, console panel, switches, combination 10-4...
Page 327: Exterior Care
10-2 Appearance care Exterior care & Washing CAUTION . When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes.
Page 328: Waxing And Polishing
When in doubt, it is always best to contact your SUBARU dealer or an auto paint specia- list. CAUTION Do not use any agents with organic solvents on the surface of the bulb assembly cover.
Page 329: Corrosion Protection
Contact your SUBARU dealer to perform this kind of maintenance and treatment if you need assistance. Repair chips and scratches in the paint as soon as you find them.
Page 330: Cleaning The Interior
If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading or shrinkage.
Page 331: Navigation Monitor (If Equipped)
10-6 Appearance care & Navigation monitor (if equipped) To clean the navigation monitor, wipe it with a silicone cloth or with a soft cloth. If the navigation monitor is extremely dirty, clean it with a soft cloth moistened with neutral detergent then carefully wipe off any remaining detergent.
Page 332: Maintenance And Service
Maintenance schedule ... Maintenance precautions... Before checking or servicing in the engine compartment... When you do checking or servicing in the engine compartment while the engine is running... Engine hood ... Engine compartment overview... Engine oil... Checking the oil level ... Changing the oil and oil filter...
Page 333 Maintenance and service Replacement of wiper blades ... Windshield wiper blade assembly ... Windshield wiper blade rubber ... Rear window wiper blade assembly ... Rear window wiper blade rubber... Battery... Fuses ... Main fuse ... Installation of accessories... Replacing bulbs ... Headlights (models with HID headlights) ...
Page 334: Maintenance Schedule
Maintenance precautions When maintenance and service are re- quired, it is recommended that all work be done by an authorized SUBARU dealer. If you perform maintenance and service by yourself, you should familiarize yourself with the information provided in this section on general maintenance and service for your SUBARU.
Page 335: Before Checking Or Servicing In The Engine Compartment
NEVER use a circuit tester for these wiring. If your SRS airbag or seatbelt preten- sioner needs service, consult your nearest SUBARU dealer. & Before checking or servicing in the engine compartment WARNING . Always stop the engine and set the parking brake firmly to pre- vent the vehicle from moving.
Page 336 3. Release the secondary hood release located under the front grille by moving the lever toward the left. 4. Lift up the hood. To close the hood: 1. Lower the hood to a point approxi- mately 20 in (50 cm) from the closed position and then give the hood a strong push down to make it drop.
Page 337: Engine Compartment Overview
11-6 Maintenance and service Engine compartment overview Air cleaner element (page 11-14) Power steering fluid reservoir (page 11-18) Differential gear oil level gauge (page 11-17) Automatic transmission fluid level gauge (page 11-16) Brake fluid reservoir (page 11-19) Fuse box (page 11-36) Battery (page 11-35) Windshield washer tank (page 11-30) Radiator cap (page 11-11)
Page 338: Engine Oil
1 quart per 1,200 miles or 1 liter per 2,000 kilometers, we recommend that you contact your SUBARU dealer. & Checking the oil level Check the engine oil level at each fuel stop.
Page 339: Changing The Oil And Oil Filter
11-8 Maintenance and service . Be careful not to spill engine oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine oil gets on the exhaust pipe, be sure to wipe it off. If you check the oil level just after stopping the engine, wait a few minutes for the oil to drain back into the oil pan before checking...
Page 340: Recommended Grade And Viscosity
8. Clean the rubber seal seating area of the bottom of engine and install the oil filter by hand turning. Be careful not to twist or damage the seal. 9. Tighten the oil filter by the amount indicated in the following table after the seal makes contact with the bottom of engine.
Page 341: Recommended Grade And Viscosity Under Severe Driving Conditions
When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity as those recommended by SUBARU. SAE viscosity number and applicable temperature 5W-30 is recommended. Engine oil viscosity (thickness) affects fuel economy.
Page 342: Cooling System
, u s e o n l y SUBARU Super Coolant. If the SUBARU Super Coolant is diluted with another brand or type, the maintenance interval is shortened to that of the mixing coolant.
Page 343 The alcohol contained in the engine coolant may damage the paint surface. ! Changing the coolant Always add genuine SUBARU cooling system conditioner whenever the coolant is replaced. Change the engine coolant and add genuine SUBARU cooling system condi-...
Page 344 SUBARU cooling system conditioner in the radiator. Add genuine SUBARU cooling system condi- tioner until the coolant level reaches the filler neck. Do not pour the coolant too quickly, as this may lead to insufficient air bleeding and trapped air in the system.
Page 345: Air Cleaner Element
CAUTION When replacing the air cleaner ele- ment, use a genuine SUBARU air cleaner element. If it is not used, there is the possibility of causing a negative effect to the engine.
Page 346: Spark Plugs
However, replacement of the belt should be done according to the main- tenance schedule in the “Warranty and Maintenance Booklet”. Consult your SUBARU dealer for replacement. If a belt is loose, cracked, or worn, contact your SUBARU dealer.
Page 347: Automatic Transmission Fluid
11-16 Maintenance and service Automatic transmission fluid & Checking the fluid level The automatic transmission fluid expands largely as its temperature rises; the fluid level differs according to fluid temperature. Therefore, there are two different scales for checking the level of hot fluid and cold fluid on the level gauge.
Page 348: Recommended Fluid
& Recommended fluid Use one of the following types of auto- matic transmission fluid. SUBARU ATF IDEMITSU ATF HP NOTE Using any non-specified type of auto- matic transmission fluid could result in damage inside the transmission. When replacing the automatic transmission fluid, be sure to use a fluid of the types specified above.
Page 349: Recommended Grade And Viscosity
Rear differential gear oil There is no rear differential gear oil level gauge. To check the rear differential gear oil level, consult your SUBARU dealer for inspection. & Recommended grade and viscosity Each oil manufacturer has its own base oils and additives.
Page 350: Recommended Fluid
. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. CAUTION . When adding brake fluid, be care- ful not to allow any dirt into the reservoir.
Page 351: Recommended Brake Fluid
Brake booster If the brake booster does not operate as described in the following, have it checked by your SUBARU dealer. 1. With the engine off, depress the brake pedal several times, applying the same pedal force each time. The distance the pedal travels should not vary.
Page 352: Brake Pedal
2 lbf (10 N, 1 kgf). If the free play is not within proper specification, contact your SUBARU deal- & Checking the brake pedal reserve distance More than 2.16 in (55 mm)
Page 353: Breaking-In Of New Brake Pads And Linings
11-22 Maintenance and service you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as possible. & Breaking-in of new brake pads and linings When replacing the brake pad or lining, use only genuine SUBARU parts. After replacement, the new parts must be broken in as follows.
Page 354: Tires And Wheels
Tires and wheels & Types of tires You should be familiar with type of tires present on your vehicle. ! All season tires The factory-installed tires on your new vehicle are all season tires. All season tires are designed to provide an adequate measure of traction, handling and braking performance in year-round driving including snowy and icy road...
Page 355: Tire Inspection
11-24 Maintenance and service not be functioning normally. In this event, go to a SUBARU dealer to have the system inspected as soon as possible. While the vehicle is driven, friction be- tween tires and the road surface causes the tires to warm up. After illumination of...
Page 356: Tire Pressures And Wear
Drive slowly to the nearest authorized SUBARU dealer and have the vehicle inspected. & Tire pressures and wear Maintaining the correct tire pressures helps to maximize the tires’...
Page 357 11-26 Maintenance and service . Correct tire pressure (tread worn evenly) Roadholding is good, and steering is responsive. Rolling resistance is low, so fuel consumption is also lower. . Abnormally low tire pressure (tread worn at shoulders) Rolling resistance is high, so fuel con- sumption is also higher.
Page 358: Wheel Balance
If you suspect that the wheels are not correctly balanced, have them checked and adjusted by your SUBARU dealer. Also have them adjusted after tire repairs and after tire rotation. NOTE...
Page 359: Tire Rotation
(tread pattern), con- struction, and size. You are advised to replace the tires with new ones that are identical to those fitted as standard equip- ment. For safe vehicle operation, SUBARU recommends replacing all four tires at the same time.
Page 360: Wheel Replacement
. Never let the wheel rub against sharp protrusions or curbs. . When wheel nuts, balance weights, or the center cap is replaced, be sure to replace them with genuine SUBARU parts designed for the specific wheel.
Page 361: Windshield Washer Fluid
In areas where water freezes in winter, use an anti-freeze type windshield washer fluid. SUBARU Windshield Washer Fluid contains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing tem- perature varies according to how much it is diluted, as indicated in the following table.
Page 362: Replacement Of Wiper Blades
If you cannot eliminate the streaking even after following this method, replace the wiper blades using the following proce- dures. Be sure to use genuine SUBARU wiper blade rubbers as replacements. – CONTINUED –...
Page 363: Windshield Wiper Blade Assembly
11-32 Maintenance and service & Windshield wiper blade as- sembly 1. Raise the windshield wiper arm on the driver’s side. 2. Next, raise the windshield wiper arm on the passenger’s side. Stopper 3. Remove the wiper blade assembly by holding its pivot area and pushing it in the direction shown by the arrow while de- pressing the wiper blade stopper.
Page 364: Rear Window Wiper Blade Assembly
3. Align the claws of the metal support with the grooves in the rubber and slide the blade rubber assembly into the metal support until it locks. Stopper 4. Be sure to position the claws at the end of the metal support between the stoppers on the rubber as shown.
Page 365 11-34 Maintenance and service 1. Pull out the end of the blade rubber assembly to unlock it from the plastic support. 2. Pull the blade rubber assembly out of the plastic support. Metal spines 3. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber.
Page 366: Battery
Battery WARNING . Before beginning work on or near any battery, be sure to extinguish all cigarettes, matches, and light- ers. Never expose a battery to an open flame or electric sparks. Batteries give off a gas which is highly flammable and explosive. .
Page 367: Fuses
11-36 Maintenance and service Fuses CAUTION Never replace a fuse with one hav- ing a higher rating or with material other than a fuse because serious damage or a fire could result. The fuses are designed to melt during an overload to prevent damage to the wiring harness and electrical equipment.
Page 368: Main Fuse
6. If the same fuse blows again, this indicates that its system has a problem. Contact your SUBARU dealer for repairs. 11-37 Maintenance and service Main fuse Main fuse box...
Page 369: Installation Of Accessories
11-38 Maintenance and service Installation of accessories Always consult your SUBARU dealer before installing fog lights or any other electrical equipment in your vehicle. Such accessories may cause the electronic system to malfunction if they are incor- rectly installed or if they are not suited for the vehicle.
Page 370 NOTE . If headlight aiming is required, con- sult your SUBARU dealer for proper adjustment of the headlight aim. . It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary. ! Low beam light bulbs (right-hand side) 1.
Page 371: Parking Light (Right-Hand Side)
2. Pull the bulb out of the socket. 3. Install a new bulb. 4. Set the bulb socket into the headlight assembly and turn it clockwise until it locks. NOTE Contact your SUBARU dealer for the bulb replacement of the left-hand side.
Page 372: Front Turn Signal Light (Right-Hand Side)
Contact your SUBARU dealer for the bulb replacement of the left-hand side. & Front fog light It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary. 11-41 Maintenance and service & Rear combination lights 1.
Page 373: Back-Up Light/Tail Light
11-42 Maintenance and service the rear combination light assembly rear- ward and remove it from the vehicle. Brake/tail light Rear turn signal light 3. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise. 4. Remove the bulb from the socket by pushing it and turning counterclockwise.
Page 374: Rear Gate Light
2. Turn the bulb socket counterclockwise and remove it. 3. Pull the bulb out of the bulb socket and replace it with a new one. 4. Install the bulb socket by turning it clockwise. 5. Install the light cover on the rear gate. &...
Page 375: Dome Light
11-44 Maintenance and service 4. Pull the bulb out of the socket. Install a new bulb. 5. Set the bulb socket into the license plate light assembly and turn it clockwise until it locks. 6. Reinstall the license plate light assem- bly to the rear gate.
Page 376: Map Light
2. Pull the bulb out of the socket. 3. Install a new bulb. 4. Reinstall the lens. & Door step light It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary. – CONTINUED –...
Page 377: Cargo Area Light
11-46 Maintenance and service & Cargo area light 1. Remove the cargo area light assembly by prying the edge of the light with a flat- head screwdriver. 2. Remove the lens from the cargo area light assembly. 3. Pull the bulb out of the socket. 4.
Page 378: Specifications
Specifications ... 12-2 Dimensions... Engine ... Electrical system... Capacities ... Tires ... Wheel alignment ... Fuses and circuits ... 12-2 Fuse panel located in the passenger compartment ... 12-2 Fuse panel located in the engine 12-3 compartment ... 12-3 Bulb chart... 12-4 Vehicle identification ...
Page 379: Dimensions
12-2 Specifications Specifications These specifications are subject to change without notice. & Dimensions Overall length Overall width Overall height Without roof rail With roof rail Wheel base Tread Front Rear Ground clearance & Engine Engine model Engine type Displacement cc (cu-in) Bore 6 Stroke in (mm) Compression ratio Firing order...
Page 380: Electrical System
& Electrical system Battery type and capacity (5HR) Alternator Spark plugs & Capacities Fuel tank Engine oil Transmission fluid Front differential gear oil Rear differential gear oil Power steering fluid Engine coolant Each quantity indicated above is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other factors.
Page 381: Tires
12-4 Specifications & Tires Tire size Wheel size Pressure Front Rear Temporary spare tire Size Pressure Wheel nut tightening torque Aluminum wheels (silver-colored) Chrome-finished wheels Temporary spare tire wheel *1: This torque is equivalent to applying the following load at the end of the wheel nut wrench. When you use a wheel nut wrench of the 10.8-inch (275 mm) length: Approximately 96 to 115 lbf (43 to 52 kgf) When you use a wheel nut wrench of the 13.2-inch (335 mm) length: Approximately 73 to 87 lbf (33 to 40 kgf) If you have tightened the wheel nuts by yourself, have the tightening torque checked at the nearest automotive service facility as soon as possible.
Page 382: Wheel Alignment
& Wheel alignment Front Rear Camber* Front Rear *: The difference between right-hand camber and left-hand camber should be within 45’ or less. Specifications 0+0.12 in (0+3 mm) Toe angle (sum of both wheels): 08+0814’ 0.08+0.08 in (2+2 mm) Toe angle (sum of both wheels): 0810’+0810’ 0810’+0845’...
Page 383: Fuses And Circuits
12-6 Specifications Fuses and circuits & Fuse panel located in the passenger compartment Fuse Fuse Circuit panel rating Trailer hitch connector Empty Door locking 7.5A Front wiper deicer relay Moonroof 7.5A Combination meter 7.5A Remote control rear view mirrors Seat heater relay Combination meter Integrated unit Stop light...
Page 384 Fuse Fuse Circuit panel rating Cargo socket Position light Tail light Rear combination light Empty Illumination Seat heaters Back-up light Headlight right side re- 7.5A Empty 7.5A Starter relay Air conditioner Rear window defogger relay coil Rear wiper Rear window washer Audio unit airbag system...
Page 385: Fuse Panel Located In The Engine Compartment
12-8 Specifications & Fuse panel located in the engine compartment Fuse Fuse Circuit panel rating Vehicle Dynamics Con- trol unit Main fan (cooling fan) Main fan (cooling fan) Console socket Headlight (right side) Headlight (left side) Backup Horn Rear window defogger Fuel pump Automatic transmission...
Page 386: Bulb Chart
12-9 Specifications Bulb chart NOTE Lights A and B are the LED (Light Emitting Diode) type. Consult your SUBARU dealer for replacement. – CONTINUED –...
Page 387: Specifications
– Do not replace any headlight bulbs (both low beam and high beam) by yourself. – Do not remove/restore the headlight assemblies by your- self. – Do not remove any headlight- assembly components by yourself. For replacement, contact your SUBARU dealer.
Page 388 12-11 Specifications CAUTION Replace any bulb only with a new bulb of the specified wattage. Using a bulb of different wattage could result in a fire.
Page 389: Vehicle Identification
12-12 Specifications Vehicle identification Vehicle identification number Certification and bar code label Tire inflation pressure label Vehicle identification number plate Model number label Emission control label Fuel label Air conditioner label...
Page 390 Consumer information and Reporting safety defects For U.S.A..13-2 Tire information ... 13-2 Tire labeling ... Recommended tire inflation pressure... Glossary of tire terminology ... Tire care – maintenance and safety practices... Vehicle load limit – how to determine... Determining compatibility of tire and vehicle load capacities ...
Page 391: Consumer Information And Reporting Safety Defects
13-2 Consumer information and Reporting safety defects For U.S.A. The following information has been compiled according to Code of Federal Regulations “Title 49, Part 575”. Tire information & Tire labeling Many markings (e.g. Tire size, Tire Identification Number or TIN) are placed on the sidewall of a tire by tire manufacturers.
Page 392 Example: (6) Load Index: A numerical code which specifies the maximum load a tire can carry at the speed indicated by its speed symbol, at maximum inflation pressure. For example, “104” means 1,984 lbs (900 kg), “100” means 1,764 lbs (800 kg), “90”...
Page 393: Recommended Tire Inflation Pressure
13-4 Consumer information and Reporting safety defects ! Maximum load rating The load rating at the maximum permissible weight load for this tire. For example, “MAX. LOAD 730 kg (1609 LBS) @ 300 kPa (44 PSI) MAX. PRESS.” WARNING Maximum load rating applies only to the tire, not to the vehicle.
Page 394: Glossary Of Tire Terminology
Example: The vehicle placard shows original tire size, recommended cold tire inflation pressure on each tire at maximum loaded vehicle weight, seating capacity and loading infor- mation. ! Adverse safety consequences of under-inflation Driving at high speeds with exces- sively low tire pressures can cause the tires to flex severely and to rapidly become hot.
Page 395 13-6 Consumer information and Reporting safety defects sidewall rubber which, when in- flated, bears the load. Chunking The breaking away of pieces of the tread or sidewall. Cold tire pressure The pressure in a tire that has been driven less than 1 mile or has been standing for three hours or more.
Page 396 Measuring rim The rim on which a tire is fitted for physical dimension requirements. Normal occupant weight 150 lbs (68 kg) times the number of occupants specified in the second column of Table 1 that is appended to the end of this section. Occupant distribution Distribution of occupants in a vehi- cle as specified in the third column...
Page 397 13-8 Consumer information and Reporting safety defects Rim type designation The industry of manufacturer’s des- ignation for a rim by style or code. Rim width Nominal distance between rim flanges. Section width The linear distance between the exteriors of the sidewalls of an inflated tire, excluding elevations due to labeling, decoration, or protective bands.
Page 398: Tire Care - Maintenance And Safety Practices
Table 1 — Occupant loading and distribution for vehicle normal load for various designated seating capacities Designated seating Vehicle normal load, capacity, number of number of occupants occupants 2 through 4 5 through 10 11 through 15 16 through 22 Consumer information and Reporting safety defects Occupant distribution in a normally loaded vehicle...
Page 399: Vehicle Load Limit - How To Determine
13-10 Consumer information and Reporting safety defects To maximize the life of each tire and ensure that the tires wear uniformly, it is best to rotate the tires every 7,500 miles (12,000 km). For information about the tire rota- tion order, refer to “Tire rotation” F11-28 Replace any damaged or unevenly worn tires at the time of...
Page 400 For example, if the vehicle has one occupant weighing 154 lbs (70 kg) plus cargo weighing 882 lbs (400 kg). Calculate the total weight. Calculate the available load ca- pacity by subtracting the total weight from the vehicle capacity weight of 1,157 lbs (525 kg). The result of step 2 shows that a further 121 lbs (55 kg) of cargo can be carried.
Page 401 13-12 Consumer information and Reporting safety defects vehicle is 1,157 lbs (525 kg), which is indicated on the vehicle placard with the statement “The combined weight of occupants and cargo should never exceed 525 kg or 1,157 lbs”. For example, the vehicle has one occupant weighing 165 lbs (75 kg) plus cargo weighing 705 lbs (320 kg).
Page 402: Determining Compatibility Of Tire And Vehicle Load Capacities
The total weight now exceeds the capacity weight by 105 lbs (48 kg), so the cargo weight must be reduced by 105 lbs (48 kg) or more. & Determining compatibility of tire and vehicle load capaci- ties The sum of four tires’ maximum load ratings must exceed the max- imum loaded vehicle weight (“GVWR”).
Page 403: Uniform Tire Quality Grading Standards
13-14 Consumer information and Reporting safety defects The resulting figure equals the available amount of cargo and luggage load capacity. For exam- ple, if the “XXX” amount equals 1,400 lbs (635 kg) and there will be five- 150 lbs (68 kg) passengers in your vehicle, the amount of avail- able cargo and luggage load capa- city is 650 lbs.
Page 404: Temperature A, B, C
However, NHTSA cannot become involved in individual problems between you, your dealer, or Subaru of America, Inc. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov;...
Page 405 13-16 Consumer information and Reporting safety defects Building, Washington, DC 20590. You can also obtain other informa- tion about motor vehicle safety from http://www.safercar.gov.
Page 406: Index
Index...
Page 407 14-2 Index ABS (Anti-lock Brake System) ... 7-20 Warning light ... 3-15, 7-21 Accessories... 5-2, 11-38 Accessory power outlet... 6-10 Active head restraint... 1-6 Air cleaner element ... 11-14 Air conditioner Automatic climate control system ... 4-5 Air filtration system... 4-11 Airflow ...
Page 408 Braking ... 7-19 Tips... 7-19 Breaking-in of new brake pads and linings ... 11-22 Bulb Chart ... 12-8 Replacing... 11-38 Capacities ... 12-3 Cargo area Cover ... 6-14 Light... 6-3 Tie-down hooks ... 6-16 Catalytic converter ... 8-3 Center Console ... 6-6 Ventilators ...
Page 409 14-4 Index Second-row seat... 6-9 Third-row seat ... 6-9 Daytime running light system... 3-27 Differential gear oil Front ... 11-17 Rear... 11-18 Dimensions ... 12-2 Disarming the alarm system ... 2-18 Disc brake pad wear warning indicators ... 7-20 Dome light ... 6-2, 11-44 Door Locks ...
Page 410 Seatbelt pretensioners ... 1-28 Turn signal light ... 11-41 Front seats... 1-2 Active head restraint... 1-6 Forward and backward adjustment ... 1-3 Head restraint adjustment ... 1-5 Lumbar support ... 1-7 Memory function ... 1-4 Power seat... 1-3 Reclining... 1-3 Seat height adjustment ...
Page 411 14-6 Index Immobilizer... 3-19 Security ... 2-4, 3-19 Select lever/Gear position ... 3-20 SPORT mode... 3-20 Traction control system OFF... 7-25 Turn signal ... 3-20 Vehicle Dynamics Control OFF ... 3-18 Vehicle Dynamics Control operation ... 3-18, 7-25 Inside mirror ... 3-37 Interior lights ...
Page 412 New vehicle break-in driving... 8-2 Odometer... 3-6 Oil filter... 11-8 Oil level Engine... 11-7 Front differential gear ... 11-17 Rear differential gear ... 11-18 Oil pressure warning light... 3-13 On-pavement and off-road driving ... 8-5 Outside Mirror defogger ... 3-42 Mirrors ...
Page 413 14-8 Index Spark plugs... 11-15, 12-3 Refueling ... 7-3 Remote engine start system ... 7-8 Remote keyless entry system ... 2-8 Replacement Brake pad and lining ... 11-21 Wiper blades ... 11-31 Replacing Air cleaner element ... 11-14 Battery (remote keyless entry system) ... 2-11 Lost transmitters (remote keyless entry system) ...
Page 414 Select lever ... 7-13 Position indicator ... 3-20 Shift lock function... 7-14 Shift lock release ... 7-14 Shock sensors... 2-20 Shopping bag hook ... 6-13 Snow tires... 8-10, 11-23 Snowy and icy roads ... 8-9 Sounding a panic alarm ... 2-11 Spare tire...
Page 415 14-10 Index Top tether anchorages ... 1-38, 1-41 Towing... 9-14 All wheels on the ground ... 9-17 Flat-bed truck ... 9-17 Hooks... 9-15 Weight... 8-20 Traction Control system OFF indicator light... 3-18, 7-25 OFF switch ... 7-27 Trailer Connecting... 8-18 Hitch ...
Page 416 Aluminum... 11-29 Balance ... 11-27 Nut tightening torque ... 12-4 Replacement ... 11-29 Windows... 2-21 Windshield Washer fluid ... 11-30 Wiper and washer switches... 3-33 Wiper blades ... 11-32 Wiper deicer... 3-35 Winter Driving... 8-7 Tires... 8-10, 11-23 Wiper and washer ... 3-32 Wiper deicer...
Page 417 Compass calibration zones...
Page 418 & Fuel Use unleaded gasoline with an octane rating of 87 AKI or higher. & Fuel octane rating This octane rating is the average of the Research Octane and Motor Octane numbers and is commonly referred to as the Anti Knock Index (AKI).

Subaru 2011 Tribeca Owner's Manual

Table of Contents

Table of Contents

Front Seats

Seat Heater (if Equipped)

Second-Row Seats

Third-Row Seat

Seatbelts

Front Seatbelt Pretensioners

Child Restraint Systems

SRS Airbag (Supplemental Restraint System Airbag)

Keys and Doors

Keys

Immobilizer

Door Locks

Power Door Locking Switches

Remote Keyless Entry System

Alarm System

Windows

Child Safety Locks

Rear Gate

Moonroof (if Equipped)

Instruments and Controls

Climate Control

Ventilator

Automatic Climate Control System

Operating Tips for Heater and Air Conditioner

Air Filtration System

Audio

Antenna System

Installation of Accessories

Audio Set

Type a Audio Set (if Equipped)

Type B Audio Set (if Equipped)

Audio Control Buttons

Auxiliary Input Jack

Rear Seat Entertainment (RSE) System

Precautions to Observe When Handling a Compact Disc

Interior Equipment

Starting and Operating

Quick Links

Chapters

Related Manuals for Subaru 2011 Tribeca

Summary of Contents for Subaru 2011 Tribeca