Page 1 Foreword Congratulations on choosing a SUBARU vehicle. This Owner’s Manual has all the information necessary to keep your SUBARU in excellent condition and to properly maintain the emission control system for minimizing emission pollutants. We urge you to read this manual carefully so that you may understand your vehicle and its operation.
Page 2 This manual describes the following vehicle types.* * The illustrated vehicle is one of the FORESTER series.
Page 4: Seat, Seatbelt And Srs Airbags
Warranties & Warranties for U.S.A. All SUBARU vehicles distributed by Subaru of America, Inc. and sold at retail by an authorized SUBARU dealer in the United States come with the following warranties: . SUBARU Limited Warranty . Emission Control Systems Warranty .
Page 5: Climate Control
This chapter informs you how to keep your SUBARU looking good. Chapter 11: Maintenance and service This chapter informs you when you need to take your SUBARU to the dealer for scheduled maintenance and informs you how to keep your SUBARU running properly.
Page 6: Abbreviation List
& Abbreviation list You will find several abbreviations in this manual. The meanings of the abbrevia- tions are shown in the following list. Abbreviation Meaning Air conditioner Automatic/Emergency locking A/ELR retractor Anti-lock brake system Anti knock index Automatic locking retractor Automatic transmission Automatic transmission fluid All-wheel drive...
Page 7 Mark Name Hazard warning flasher Engine hood Seat heater Child restraint top tether an- chorages Child restraint lower an- chorages Horn Wiper intermittent Windshield washer Windshield wiper mist (for single wipe) Rear window wiper Rear window washer Mark Name Lights Tail lights, license plate light and instrument panel illumi- nation...
Page 8: Child Safety
Safety precautions when driving & Seatbelt and SRS airbag WARNING . All persons in the vehicle should fasten their seatbelts BEFORE the vehicle starts to move. Other- wise, the possibility of serious injury becomes greater in the event of a sudden stop or acci- dent.
Page 9 The SRS airbag deploys with considerable speed and force and can injure or even kill chil- dren, especially if they are 12 years of age and under and are not restrained or improperly re- strained. Because children are lighter and weaker than adults, their risk of being injured from deployment is greater.
Page 10: Drinking And Driving
& Drinking and driving WARNING Drinking and then driving is very dangerous. Alcohol in the blood- stream delays your reaction time and impairs your perception, judg- ment and attentiveness. If you drive after drinking – even if you drink just a little –...
Page 11: Driving With Pets
& Modification of your vehicle CAUTION Your vehicle should not be modified other than with genuine SUBARU parts and accessories. Other types of modifications could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or...
Page 12: California Proposition 65
& California proposition 65 warning WARNING Engine exhaust, some of its consti- tuents, and certain vehicle compo- nents contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addi- tion, certain fluids in vehicles and certain components of product wear contain or emit chemicals known to...
Page 13 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 14: Table Of Contents
Table of contents Seat, seatbelt and SRS airbags Keys and doors Instruments and controls Climate control Audio Interior equipment Starting and operating Driving tips In case of emergency Appearance care Maintenance and service Specifications Consumer information and Reporting safety defects Index...
Page 15 Illustrated index & Exterior Engine hood (page 11-5) Headlight switch (page 3-30) Replacing bulbs (page 11-47) Wiper switch (page 3-34) Moonroof (page 2-25) Roof rail (page 8-14) Door locks (page 2-4) Tire pressure (page 11-33) Flat tires (page 9-6) 10) Tire chains (page 8-11) 11) Front fog light switch (page 3-32) 12) Tie-down hooks (page 9-14) 13) Towing hook (page 9-14)
Page 16 Rear window defogger button (page 3-45) Fuel filler lid and cap (page 7-3) Child safety locks (page 2-20) Tie-down hook (page 9-14) Rear gate (page 2-23) Towing hook (page 9-14) – CONTINUED –...
Page 17 & Interior ! Passenger compartment area Lower anchorages for child restraint system (page 1-29) Seatbelt (page 1-12) Parking brake lever (page 7-29) Front seat (page 1-2) Rear seat (page 1-7)
Page 18 Center console (page 6-5) Cup holder (page 6-8) Front power supply socket (page 6-9) Glove box (page 6-5) – CONTINUED –...
Page 19 & Instrument panel Door locks (page 2-4) Outside mirror switch (page 3-44) Illumination brightness control (page 3-32) Light control lever (page 3-29) Combination meter (page 3-6) Wiper control lever (page 3-33) Hazard warning flasher switch (page 3-5) Audio (page 5-1) Shift lever (MT) (page 7-13)/ Select lever (AT) (page 7-15) 10) Climate control (page 4-1)
Page 20 & Light control and wiper control levers/switches Windshield wiper (page 3-34) Mist (page 3-35) Windshield washer (page 3-35) Rear window wiper and washer switch (page 3-36) Wiper intermittent time control switch (page 3-35) Wiper control lever (page 3-33) Light control switch (page 3-29) Fog light switch (page 3-32) Headlight ON/OFF (page 3-30) 10) Headlight flasher High/Low beam...
Page 21 & Combination meter ! Type A Tachometer (page 3-10) Trip meter and odometer (page 3-8) Select lever and gear position indicator (page 3-24) Speedometer (page 3-8) Information display switching knob (page 3-26) ECO gauge (page 3-12) Fuel gauge (page 3-10) Temperature gauge (page 3-11) Trip meter A/B selection and trip meter reset knob (page 3-6)
Page 22 ! Type B (U.S.-spec. models) Tachometer (page 3-10) Speedometer (page 3-8) Fuel gauge (page 3-10) Trip meter A/B selection and trip meter reset knob (page 3-6) Odometer/Trip meter (page 3-8) Select lever and gear position indicator (AT models) (page 3-24) Coolant temperature low indicator light/ Coolant temperature high warning light (page 3-16)
Page 23 ! Type B (except U.S.-spec. models) Tachometer (page 3-10) Speedometer (page 3-8) Fuel gauge (page 3-10) Trip meter A/B selection and trip meter reset knob (page 3-6) Odometer/Trip meter (page 3-8) Select lever and gear position indicator (AT models) (page 3-24) Coolant temperature low indicator light/ Coolant temperature high warning light (page 3-16)
Page 24: Warning And Indicator Lights
& Warning and indicator lights Mark Name Page Seatbelt warning light 3-13 Front passenger’s seat- 3-13 belt warning light SRS airbag system 3-15 warning light Front passenger’s fron- 3-15 tal airbag ON indicator Front passenger’s fron- 3-15 tal airbag OFF indicator CHECK ENGINE warning light/Malfunction 3-16...
Page 25 Function settings A SUBARU dealer can change the settings of the functions shown in the following table to meet your personal requirements. Contact the nearest SUBARU dealer for details. If your vehicle is equipped with the genuine SUBARU navigation system, the settings for some of these functions can be changed using the navigation monitor.
Page 26 1-12 Models with SRS airbags and lap/shoulder 1-13 restraints for driver, front passenger, and window-side rear passengers... 1-13 SUBARU advanced frontal airbag system ... 1-13 SRS side airbag and SRS curtain airbag... 1-13 SRS airbag system monitors... 1-19 SRS airbag system servicing ...
Page 27: Seat, Seatbelt And Srs Airbags
Seat, seatbelt and SRS airbags Front seats WARNING . Never adjust the seat while driv- ing to avoid the possibility of loss of vehicle control and of personal injury. . Before adjusting the seat, make sure the hands and feet of rear seat passengers and cargo are clear of the adjusting mechan- ism.
Page 28: Manual Seat
restraint device or in a seatbelt, whichever is appropriate for the child’s age, height and weight. Se- cure ALL types of child restraint devices (including forward facing child seat) in the REAR seats at all times. NEVER INSTALL A REARWARD FA- CING CHILD SEAT IN THE FRONT SEAT.
Page 29: Power Seat (Driver's Seat - If Equipped)
Seat, seatbelt and SRS airbags WARNING To prevent the passenger from slid- ing under the seatbelt in the event of a collision, always put the seatback in the upright position while the vehicle is in motion. Also, do not place objects such as cushions between the passenger and the seatback.
Page 30: Head Restraint Adjustment
justment of the seat, you cannot adjust the seat cushion angle or seat cushion height. Seat cushion angle control switch To adjust the seat cushion angle, pull up or push down the front end of the control switch. Seatback angle (reclining) control switch To adjust the angle of the seatback, move the control switch.
Page 31: Active Head Restraint
. If your vehicle is involved in a rear-end collision, have an authorized SUBARU dealer in- spect the active head restraints. . The active head restraints may not operate in the event the vehicle experiences only a slight impact in the rear.
Page 32: Rear Seats
HI – Rapid heating LO – Normal heating OFF – Off Left-hand side Right-hand side The seat heater operates when the igni- tion switch is either in the “Acc” or “ON” position. To turn on the seat heater, press the “LO” or “HI”...
Page 33: Armrest
Seat, seatbelt and SRS airbags WARNING Never stack luggage or other cargo higher than the top of the seatback because it could tumble forward and injure passengers in the event of a sudden stop or accident. & Armrest To lower the armrest, pull on the top edge of the armrest.
Page 34 ! Rear windows side seating position Head restraint Release button To remove: While pressing the release button, pull out the head restraint. To install: Install the head restraint into the holes that are located on the top of the seatback until the head restraint locks.
Page 35: Reclining The Seatback (If Equipped)
1-10 Seat, seatbelt and SRS airbags appropriate position depending on your sitting height. When the rear center seat- ing position is not occupied, lower the head restraint to improve rearward visibi- lity. & Reclining the seatback (if equipped) WARNING To prevent the passenger from slid- ing under the seatbelt in the event of a collision, always put the seatback in the upright position while the...
Page 36 ing down the rear seatback, re- turn the rear seat center table to its original position. If the rear seat center table is not returned to its original position, the rear seat center table could break and bodily injury could occur. .
Page 37: Seatbelts
1-12 Seat, seatbelt and SRS airbags Seatbelts & Seatbelt safety tips WARNING . All persons in the vehicle should fasten their seatbelts BEFORE the vehicle starts to move. Other- wise, the possibility of serious injury becomes greater in the event of a sudden stop or acci- dent.
Page 38: Emergency Locking Retractor (Elr)
tions only) and then if necessary move the child closer to the belt buckle to help provide a good shoulder belt fit. Care must be taken to securely place the lap belt as low as possible on the hips and not on the child’s waist.
Page 39 1-14 Seat, seatbelt and SRS airbags . Seatbelts provide maximum re- straint when the occupant sits well back and upright in the seat. To reduce the risk of sliding under the seatbelt in a collision, the front seatbacks should be always used in the upright posi- tion while the vehicle is running.
Page 40 4. Insert the tongue plate into the buckle until you hear a click. 5. To make the lap part tight, pull up on the shoulder belt. 6. Place the lap belt as low as possible on your hips, not on your waist. ! Adjusting the front seat shoulder belt anchor height The shoulder belt anchor height should be...
Page 41 1-16 Seat, seatbelt and SRS airbags ! Rear seatbelts (except rear center seatbelt) 1. Sit well back in the seat. 2. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly.
Page 42 WARNING Fastening the seatbelt with the web- bing twisted can increase the risk or severity of injury in an accident. When fastening the belt after it is pulled out from the retractor, espe- cially when inserting the connec- tor’s tongue plate into the mating buckle (on right-hand side), always check that the webbing is not twisted.
Page 43 1-18 Seat, seatbelt and SRS airbags 2. After drawing out the seatbelt, pass it through the belt guide. 3. After confirming that the webbing is not twisted, insert the connector (tongue) attached at the webbing end into the buckle on the right-hand side until a click is heard.
Page 44: Seatbelt Maintenance
1. Insert a key or other hard pointed object into the slot in the connector (buckle) on the right-hand side and push it in, and the connector (tongue) plate will disconnect from the buckle. 2. Allow the retractor to roll up the belt. You should hold the webbing end and guide it back into the retractor while it is rolling up.
Page 45: Front Seatbelt Pretensioners
SUBARU dealer. When replacing seat- belt retractor assemblies, use only genuine SUBARU parts. . If either front seatbelt does not...
Page 46: System Monitors
SUBARU dealer as soon as possible. & Precautions against vehicle modification Always consult your SUBARU dealer if you want to install any accessory parts to your vehicle. CAUTION Do not perform any of the following modifications.
Page 47: Child Restraint Systems
1-22 Seat, seatbelt and SRS airbags Child restraint systems Infants and small children should always be placed in an infant or child restraint system in the rear seat while riding in the vehicle. You should use an infant or child restraint system that meets Federal Motor Vehicle Safety Standards or Canada Motor Vehicle Safety Standards, is com-...
Page 48: Where To Place A Child Restraint System
& Where to place a child re- straint system The following are SUBARU’s recommen- dations on where to place a child restraint system in your vehicle. A: Front passenger’s seat You should not install a child restraint...
Page 49: Choosing A Child Restraint System
1-24 Seat, seatbelt and SRS airbags cording to accident statistics, chil- dren are safer when properly re- strained in the rear seating posi- tions than in the front seating posi- tions. WARNING S I N C E Y O U R V E H I C L E EQUIPPED WITH A PASSENGER’S SRS AIRBAG, NEVER INSTALL A R E A R W A R D FA C I N G C H I L D...
Page 50 child suffering personal injury in the event of an accident may be in- creased. ! Installing a rearward facing child restraint 1. Place the child restraint system in the rear seating position. 2. Run the lap and shoulder belt through or around the child restraint system following the instructions provided by its manufacturer.
Page 51 1-26 Seat, seatbelt and SRS airbags 8. To remove the child restraint system, press the release button on the seatbelt buckle and allow the belt to retract completely. The belt will return to the ELR mode. WARNING NEVER INSTALL A REARWARD FA- CING CHILD SEAT IN THE FRONT PASSENGER’S SEAT.
Page 52: Installing A Booster Seat
6. Before having a child sit in the child restraint system, move it back and forth and right and left to check if it is firmly secured. Sometimes a child restraint can be more firmly secured by pushing it down into the seat cushion and then tightening the seatbelt.
Page 53 1-28 Seat, seatbelt and SRS airbags injuries or death to the child. CAUTION When you install a child restraint system, follow the manufacturer’s instructions supplied with it. After installing the child restraint system, check to ensure that it is held securely in position.
Page 54: Installation Of Child Restraint Systems By Use Of Lower And Tether Anchorages (Latch)
& Installation of child restraint systems by use of lower and tether anchorages (LATCH) WARNING . Child restraint systems and seat- belts can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child.
Page 55 1-30 Seat, seatbelt and SRS airbags the rear seat window-side seating posi- tions. For each window-side seating posi- tion, two lower anchorages are provided. Each lower anchorage is located where the seat cushion meets the seatback. The tether anchorages (upper an- chorages) are provided at the locations shown in the above illustration.
Page 56: Top Tether Anchorages
If you have any question concerning this type of child restraint system, ask your SUBARU dealer. 1-31 Seat, seatbelt and SRS airbags & Top tether anchorages Your vehicle is equipped with three top...
Page 57 1-32 Seat, seatbelt and SRS airbags ! Anchorage location For right seat For center seat For left seat There is an anchorage located on the rear edge of the ceiling above each seating position. ! To hook the top tether 1.
Page 58: Srs Airbag (Supplemental Restraint System Airbag)
Please contact your SUBARU dealer if you have any question regarding the installation of a child restraint system. CAUTION Always remove the headrest when mounting a child restraint system with a top tether. Otherwise, the top tether cannot be fastened tightly.
Page 59 1-34 Seat, seatbelt and SRS airbags refer to “Seatbelts” F1-12. . Do not sit or lean unnecessarily close to the SRS airbag. Because the SRS airbag deploys with considerable speed – faster than the blink of an eye – and force to protect in high speed collisions, the force of an airbag can injure an occupant whose body is too...
Page 60 positions than in the front seat- ing positions. For instructions and precautions concerning the child restraint system, refer to “Child restraint systems” F1-22. . NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG.
Page 61 1-36 Seat, seatbelt and SRS airbags ! Components Airbag control module (including impact and rollover sensors) Frontal airbag module (driver’s side) Frontal airbag module (front passenger’s side) Front sub sensor (left-hand side) Front sub sensor (right-hand side) Side airbag module (driver’s side) Side airbag module (front passenger’s side) Side airbag sensor (center pillar left-hand...
Page 62: Subaru Advanced Frontal Airbag System
& SUBARU advanced frontal airbag system Your vehicle is equipped with a SUBARU advanced frontal airbag system that com- plies with the new advanced frontal airbag requirements in the amended Federal Motor Vehicle Safety Standard (FMVSS) No. 208. The SUBARU advanced frontal airbag system automatically determines the de- ployment force of the driver’s SRS frontal...
Page 63 1-38 Seat, seatbelt and SRS airbags WARNING Never hold a child on your lap or in your arms. The SRS airbag deploys with considerable force and can injure or even kill the child. WARNING The SRS airbag deploys with con- siderable speed and force.
Page 64 SRS frontal airbag even when the driver’s SRS frontal airbag deploys. This is normal. Observe the following precautions. Failure to do so may prevent the SUBARU advanced frontal airbag system from functioning correctly or cause the system to fail.
Page 65 Seat, seatbelt and SRS airbags have failed, the SRS airbag system warning light will illuminate. Have the system inspected by your SUBARU deal- er immediately if the SRS airbag system warning light illuminates. If your vehicle has sustained impact, this may affect the proper function of the SUBARU advanced frontal airbag system.
Page 66 OFF indicator turns off after taking relevant corrective actions de- scribed above, relocate the child restraint system to the rear seat and immediately contact your SUBARU dealer for an inspection. NOTE When a child who has outgrown a child restraint system or a small adult is seated in the front passenger’s seat,...
Page 67 Subaru of America, Inc. Customer Dealer Services Department P.O. Box 6000 Cherry Hill, NJ 08034-6000 1-800-SUBARU3 (1-800-782-2783) <Hawaii> Servco Subaru Inc., dba Subaru Hawaii 2850 Pukoloa Street, Suite 202, Honolulu, HI 96819 808-839-2273 <Guam> Shen’s Corporation dba Prestige Automo- bile...
Page 68 you bought your vehicle. ! Operation Driver’s side Passenger’s side SRS AIRBAGs deploy as soon as a collision occurs. After deployment, SRS AIRBAGs start to deflate immediately so that the driver’s vision is not obstructed. 1-43 Seat, seatbelt and SRS airbags –...
Page 69 Seat, seatbelt and SRS airbags The SRS airbag can function only when the ignition switch is in the “ON” position. The SUBARU advanced frontal airbag system is designed to determine the activation or deactivation condition of the front passenger’s SRS frontal airbag depending on the total load on the front passenger’s seat monitored by the front...
Page 70 ! Example of accident in which the driver’s/driver’s and front passen- ger’s SRS frontal airbag(s) will most likely deploy. A head-on collision against a thick con- crete wall at a vehicle speed of 12 to 19 mph (20 to 30 km/h) or higher activates only the driver’s SRS frontal airbag or both driver’s and front passenger’s SRS frontal airbags.
Page 71 1-46 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which deployment of the driver’s/driver’s and front passenger’s SRS frontal airbag(s) is unlikely to occur. The vehicle strikes an object, such as a telephone pole or sign pole. The vehicle slides under the load bed of a truck.
Page 72: Srs Side Airbag And Srs Curtain Airbag
! Examples of the types of accidents in which the driver’s/driver’s and front passenger’s SRS frontal airbag(s) will basically not deploy. The driver’s and front passenger’s SRS frontal airbags are designed basically not to deploy if the vehicle is struck from the side or from behind, or if it rolls onto its side or roof, or if it is involved in a low- speed frontal collision.
Page 73 1-48 Seat, seatbelt and SRS airbags WARNING The SRS side airbag and SRS curtain airbag are designed as only a supplement to the primary protec- tion provided by the seatbelt. They do not do away with the need to fasten seatbelts. It is also important to wear your seatbelt to help avoid injuries that can result when an occupant is not seated in a proper...
Page 74 WARNING . Never allow a child to kneel on the front passenger’s seat facing the side window or to wrap his/ her arms around the front seat seatback. In the event of an accident, the force of the SRS side airbag deployment could injure the child seriously be- cause his/her head or arms or other parts of the body are too...
Page 75 1-50 Seat, seatbelt and SRS airbags A hands-free microphone or other accessory in such a loca- tion could be propelled through the cabin with great force by the curtain airbag, or it could prevent correct deployment of the curtain airbag. In either case, the result could be serious injuries.
Page 76 vehicle, the control module inflates the curtain airbags. After the deployment, the SRS side airbag immediately starts to deflate. The time required from detection of an impact to deflation of an SRS side airbag after deployment is shorter than the blink of an eye.
Page 77 1-52 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which the SRS curtain airbag will most likely deploy. A severe side impact near the front seat or the rear seat activates the SRS curtain airbag. The vehicle rolls onto its side or the roof.
Page 78 ! Examples of the types of accidents in which it is possible that the SRS side airbag and the SRS curtain airbag will deploy. 1-53 Seat, seatbelt and SRS airbags Hitting a curb, edge of pavement or hard surface Falling into or jumping over a deep hole Landing hard or vehicle falling It is possible that the SRS side and curtain airbags will deploy if a serious impact...
Page 79 1-54 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which the SRS side airbag is unlikely to deploy. The vehicle is involved in an oblique side-on impact. The vehicle is involved in a side-on impact in an area outside the vicinity of the passenger compartment.
Page 80 ! Examples of the types of accidents in which the SRS curtain airbag is unlikely to deploy. 1-55 Seat, seatbelt and SRS airbags The vehicle is involved in an oblique side-on impact. The vehicle is involved in a side-on impact in an area outside the vicinity of the passenger compartment.
Page 81 1-56 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which the SRS side airbag and SRS curtain airbag will basically not deploy. The vehicle is involved in frontal collision with another vehicle (moving or station- ary).
Page 82: Srs Airbag System Monitors
SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS...
Page 83: Srs Airbag System Servicing
CAUTION If you need service or repair in areas indicated in the following list, have the work performed by an author- ized SUBARU dealer. The SRS air- bag control module, impact sensors and airbag modules are stored in these areas.
Page 84: Precautions Against Vehicle Modification
. Attachment of any equipment (side steps or side sill protectors, 1-59 Seat, seatbelt and SRS airbags etc.) other than genuine SUBARU accessory parts to the side body. Always consult your SUBARU dealer if you want to install any accessory parts on your vehicle.
Page 85 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 86 Keys ... Key number plate ... Immobilizer ... Security ID plate... Security indicator light ... Key replacement ... Door locks ... Locking and unlocking from the outside ... Locking and unlocking from the inside ... Battery drainage prevention function ... Power door locking switches ...
Page 87: Keys And Doors
Keys and doors Keys Master key (black) Submaster key (black) Valet key (gray) Key number plate Security ID plate Three types of keys are provided for your vehicle: Master key, submaster key and valet key. The master key and submaster key fit all locks on your vehicle.
Page 88: Security Id Plate
For information on replacement keys and on the registration of keys with your immo- bilizer system, contact your SUBARU dealer. NOTE A vehicle that is equipped with the...
Page 89: Door Locks
Keys and doors use with one vehicle. Door locks & Locking and unlocking from the outside NOTE If you unlock the driver’s door with a key and open the door while the alarm system is armed, the alarm system is triggered and the vehicle’s horn sounds.
Page 90: Locking And Unlocking From The Inside
Rotate the lock lever rearward. Close the door. To lock the door from the outside without the key, rotate the lock lever rearward and then close the door. To lock the door from the outside using the power door locking switch, push the front side of the switch (“LOCK”...
Page 91: Power Door Locking Switches
The operational/non-operational setting of this function can be changed by a SUBARU dealer. Contact your SUBARU dealer to change the setting. NOTE . The factory setting (default setting) for this function is set as “operational”.
Page 92: Key Lock-In Prevention Function
The setting of this function to operational/ non-operational status can be changed by a SUBARU dealer. Contact a SUBARU dealer for details. NOTE When leaving the vehicle, make sure you are holding the key before locking the doors.
Page 93: Locking The Doors
Keys and doors responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this de- vice may not cause harmful interfer- ence, and (2) this device must accept any interference received, including...
Page 94: Unlocking The Doors
The lights must be set to the DOOR position in order for this function to operate. A SUBARU dealer can change the illumi- Keys and doors nation period setting of the interior light in accordance with your preference. Contact the nearest SUBARU dealer for details.
Page 95: Sounding A Panic Alarm
You may have the above settings done by your SUBARU dealer. Contact your SUBARU dealer for details. For models with a genuine SUBARU navigation sys- tem, the settings can be changed using the navigation monitor. For details, refer to the Owner’s Manual Supplement for the...
Page 96: Replacing Lost Transmitters
tery. . Batteries should not be exposed to excessive heat such as sun- shine, fire or the like. When the transmitter battery begins to get weak, transmitter range will begin to decrease. Replace the battery as soon as possible. To replace the battery: 1.
Page 97 2-12 Keys and doors Programming transmitter codes into system: Bag containing transmitter Transmitter circuit board To register a new transmitter with the keyless entry system, it is necessary to program the transmitter’s code (identifica- tion number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the...
Page 98 NOTE . When part 4 of the procedure is completed, an electronic tone will sound for 30 seconds. . If you do not perform the operations in part 4 within 15 seconds, an error will occur and the electronic tone will not sound.
Page 99 2-14 Keys and doors NOTE If you do not start entering the number using the lock switch before the elec- tronic tone stops sounding, an error will occur. In this event, perform the procedure again beginning with part 3. 9. When you have finished entering the code a second time, an electronic tone will sound for 1 second and automatic door locking and unlocking operation will take...
Page 100: Alarm System
“DOOR” position) The notifications regarding the dome light and the map lights are deactivated as the factory setting. A SUBARU dealer can activate the system. Contact your SUBARU dealer for details. 2-15 Keys and doors &...
Page 101: If You Have Accidentally Triggered The Alarm System
2-16 Keys and doors NOTE You may have the above setting change done by your SUBARU dealer. & If you have accidentally trig- gered the alarm system ! To stop the alarm Do any of the following operations: . Press any button on the remote trans- mitter.
Page 102: Disarming The System
. The 30-second standby time can be eliminated if you prefer. Have it per- formed by your SUBARU dealer. . The system is in the standby mode for a 30-second period after locking the doors with the remote transmitter. The security indicator light will flash at short intervals during this period.
Page 103: Valet Mode
DOORS MUST BE MANUALLY LOCKED. ! To enter the passive mode If you wish to program the passive arming mode, have it done by your SUBARU dealer. ! Arming the system CAUTION In passive mode, the system will...
Page 104: Tripped Sensor Identification
30 seconds. If you desire, your SUBARU dealer can connect them and set them for activation or deactivation. NOTE . The shock sensors are not always...
Page 105: Child Safety Locks
2-20 Keys and doors Child safety locks Each rear door has a child safety lock that prevents the door from being opened even if the inside door handle is pulled. When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever.
Page 106 ! Operating the driver’s window (type Automatically open/close Open/close To open: Press the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down function that allows the window to be opened fully without holding the switch.
Page 107 2-22 Keys and doors To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held. ! Anti-entrapment function (type A) CAUTION . Never attempt to test this func- tion using fingers, hands or other parts of your body.
Page 108: Power Window Operation By Passengers
& Power window operation by passengers Each passenger window can be controlled by the power window switch located on the door. To open: Push the switch down and hold it until the window reaches the desired position. To close: Pull the switch up and hold it until the window reaches the desired position.
Page 109 2-24 Keys and doors To close: Lower the rear gate slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull it down holding the recessed grip. WARNING . To prevent dangerous exhaust gas from entering the vehicle, always keep the rear gate closed while driving.
Page 110: Moonroof (If Equipped)
Moonroof (if equipped) WARNING Never let anyone’s hands, arms, head or any objects protrude from the moonroof. A person could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is involved in an accident. To avoid serious personal injury caused by entrapment, always con- form to the following instructions...
Page 111: Anti-Entrapment Function
2-26 Keys and doors “CLOSE” or “OPEN” side. & Anti-entrapment function When the moonroof senses a substantial enough object trapped between its glass and the vehicle’s roof during closure, it automatically moves back by 6 in (15 cm) from that point and then stops. The anti- entrapment function may also be activated by a strong shock on the moonroof even when there is nothing trapped.
Page 112: Instruments And Controls
Ignition switch ... LOCK... Acc... ON... START ... Key reminder chime ... Ignition switch light ... Hazard warning flasher... Meters and gauges... Combination meter illumination ... Canceling the function for meter/gauge needle movement upon turning on the ignition switch... Meter needles/gauge illumination setting (models with type A combination meter) ...
Page 113 Instruments and controls Clock ... 3-25 Information display ... 3-26 Outside temperature indicator ... Current fuel consumption (if equipped) ... Average fuel consumption ... To turn off fuel consumption indicator display... Light control switch ... 3-29 Headlights... High/low beam change (dimmer)... Headlight flasher ...
Page 114: Ignition Switch
Ignition switch WARNING . Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.
Page 115: Acc
Instruments and controls The key can be turned from “Acc” to “LOCK” only when the select lever is in the “P” position. ! Manual transmission models The key can be turned from “Acc” to “LOCK” only when the key is pushed in while turning it.
Page 116: Key Reminder Chime
contains an immobilizer transponder. . The key is near or touching another transmitter. & Key reminder chime The reminder chime sounds when the driver’s door is opened and the ignition switch is in the “LOCK” or “Acc” position. The chime stops under the following conditions.
Page 117: Meters And Gauges
Instruments and controls Meters and gauges NOTE Liquid-crystal displays are used in some of the meters and gauges on the combination meter. You will find their indications hard to see if you wear polarized glasses. & Combination meter illumina- tion When the ignition switch is turned to the “ON”...
Page 118: Meter Needles/Gauge Illumination Setting (Models With Type A Combination Meter)
Type A: *: “ ” or “ ”, and “ ” or “ ” cannot be displayed when the ignition switch is in the “ON” position. Type B: *: “ ” or “ ” cannot be displayed when the ignition switch is in the “ON” posi- tion.
Page 119: Speedometer
Instruments and controls 2. Press the trip knob to show “ “ ” on the trip meter display. The display can be switched as shown in the following illustration by pressing the trip knob. *: “ ” or “ ”, and “ ”...
Page 120 This meter displays the odometer and two trip meters when the ignition switch is in the “ON” position. If you press the trip knob when the ignition switch is in the “LOCK” or “Acc” position, the odometer/trip meter will light up. It is possible to switch the indications while the odometer/trip meter is lit up.
Page 121: Tachometer
3-10 Instruments and controls Type B The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2 seconds.
Page 122: Temperature Gauge (Models With Type A Combination Meter)
(a) do not press the trip knob for 10 seconds or (b) open and close the driver’s door, the fuel gauge indication will turn off. NOTE You will see the “ ” sign in the fuel gauge. This indicates that the fuel filler door (lid) is located on the right side of the vehicle.
Page 123: Eco Gauge (Models With Type A Combination Meter)
3-12 Instruments and controls & ECO gauge (models with type A combination meter) The unit displayed varies depending on the model. The ECO gauge shows the difference between the average rate of fuel con- sumption since the trip meter was last reset and the current rate of fuel con- sumption.
Page 124: Seatbelt Warning Light And Chime
(models with HID head- lights) If any lights fail to illuminate, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair. & Seatbelt warning light and chime Your vehicle is equipped with a seatbelt warning device at the driver’s and front...
Page 125 If still the seatbelt warning device for front passenger’s seat does not function cor- rectly after taking relevant corrective ac- tions described above, immediately con- tact your SUBARU dealer for an inspec-...
Page 126: Srs Airbag System Warning Light
SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS...
Page 127: Check Engine Warning Light/Malfunction Indicator Lamp
CAUTION If the CHECK ENGINE light illumi- nates while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possible. Continued vehicle opera- tion without having the emission control system checked and re- paired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty.
Page 128: Charge Warning Light
After- w a r d , h a v e t h e s y s t e m checked by your nearest SUBARU dealer. Refer to “En- gine overheating” F9-13. – Blinking in RED and BLUE alternately: The electrical system may be malfunctioning.
Page 129: At Oil Temp Warning Light (At Models)
If the light flashes after the engine starts, it may indicate that the automatic transmis- sion control system is not working prop- erly. Contact your nearest SUBARU deal- er for service immediately. & Low tire pressure warning light (U.S.-spec.
Page 130: Abs Warning Light
Should the warning light illuminate stea- dily after blinking for approximately one minute, have the system inspected by your nearest SUBARU dealer as soon as possible. WARNING If this light does not illuminate briefly after the ignition switch is...
Page 131: Brake System Warning Light
If the fluid level is below the “MIN” mark in the reservoir, do not drive the vehicle. Have the vehicle towed to the nearest SUBARU dealer for repair. ! Electronic Brake Force Distribution (EBD) system warning...
Page 132: Low Fuel Warning Light
3. Release the parking brake. If both warning lights turn off, the EBD system may be malfunctioning. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights illuminate again and stay illuminated after the engine has...
Page 133: Automatic Headlight Beam Leveler Warning Light (Models With Hid Headlights)
You will be safe while driving with this condition, but drive carefully and have your vehicle checked at a SUBARU dealer as soon as possible. NOTE . If the electrical circuit of the Vehicle...
Page 134: Vehicle Dynamics Control Off Indicator Light
The Vehicle Dynamics Control system is probably malfunctioning under the follow- ing condition. Have your vehicle checked at a SUBARU dealer as soon as possible. . The light does not turn off even after the lapse of several minutes (the engine has warmed up) after the engine has started.
Page 135: Sport Mode Indicator Light (At Models)
If the security indicator light does not flash, the immobilizer system may not be func- tioning properly. If this occurs, contact your SUBARU dealer as soon as possible. In case an unauthorized key is used (e.g., an imitation key), the security indicator light illuminates.
Page 136: Turn Signal Indicator Lights
When the manual mode is selected, the gear position indicator (which shows the current gear selection) and the upshift/ downshift indicator light up. Refer to “Automatic transmission” F7-15. & Turn signal indicator lights These lights show the operation of the turn signal or lane change signal.
Page 137: Information Display
3-26 Instruments and controls CAUTION To ensure safety, do not attempt to set the time while driving, as an accident from inadequate attention to the road could result. NOTE If the battery is disconnected, the time will be erased. After reconnecting the battery, set the correct time.
Page 138: Outside Temperature Indicator
Odometer/ Fuel consumption indicator Trip meter A trip meter Average fuel consumption corresponding to the A trip meter B trip meter Average fuel consumption corresponding to the B trip meter Odometer U.S-spec. models: Not indicated Other models: Current fuel consumption &...
Page 139: Current Fuel Consumption (If Equipped)
3-28 Instruments and controls when the outside temperature drops to 378F (38C) or lower again, unless the outside temperature has increased to 418F (58C) or higher. NOTE The outside temperature indication may differ from the actual outside temperature. The road surface freeze warning indication should be treated only as a guide.
Page 140: Light Control Switch
when the battery voltage is discon- nected and then reconnected for bat- tery replacement or fuse replacement. Light control switch The light control switch only operates when the ignition key is inserted into the ignition switch. Regardless of the position of the light control switch, the illuminated lights are turned off when the ignition key is removed from the ignition switch.
Page 141: Headlights
3-30 Instruments and controls & Headlights To turn on the headlights, turn the knob on the end of the turn signal lever. first position Instrument panel illumination, tail lights, front side marker lights and license plate lights are on. second position Headlights, instrument panel illumination, tail lights, front side marker lights, and license plate lights are on.
Page 142: Daytime Running Light System (If Equipped)
& Daytime running light system (if equipped) WARNING The brightness of the illumination of the high beam headlights is reduced by the daytime running light system. The light switch must always be turned to the “ ” position when it is dark outside.
Page 143: Illumination Brightness Control
3-32 Instruments and controls Illumination brightness con- trol The brightness of clock display, audio, air conditioner, information display and instru- ment panel illumination dims when the light switch is in the “ ” or “ positions. You can adjust brightness of the instrument panel illumination for better visibility.
Page 144: Wiper And Washer
. Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. – CONTINUED –...
Page 145: Windshield Wiper And Washer Switches
3-34 Instruments and controls Refer to “Windshield washer fluid” F11-38. Also, when driving the vehicle when there are freezing tempera- tures, use non-freezing type wi- per blades. . Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzine.
Page 146 ! Wiper intermittent time control When the wiper switch is in the “ position, turn the dial to adjust the operat- ing interval of the wiper. The operating interval can be adjusted continuously from the shortest interval to the longest. The operating interval can be adjusted in nine steps.
Page 147: Rear Window Wiper And Washer Switch
3-36 Instruments and controls & Rear window wiper and washer switch : Washer (accompanied by wiper operation) ON: Continuous INT: Intermittent OFF: Off : Washer ! Rear wiper To turn the rear wiper on, turn the knob on the end of the wiper control lever upward to the “INT”...
Page 148: Auto-Dimming Mirror/Compass (If Equipped)
& Auto-dimming mirror/com- pass (if equipped) Auto dimming indicator Left (mirror) button Photosensor Right (compass) button Compass display The auto-dimming mirror has an anti-glare feature which automatically reduces glare coming from headlights of vehicles behind you. It also contains a built-in compass. .
Page 149 3-38 Instruments and controls displayed. 4. Releasing the button for 3 seconds will exit the zone setting mode. ! Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut.
Page 150 ! Photosensors The mirror has a photosensor attached on both the front and back sides. During nighttime driving, these sensors detect distracting glare from vehicle headlights behind you and automatically dim the mirror to eliminate glare and preserve your vision. For this reason, use care not to cover the sensors with stickers, or other similar items.
Page 151 3-40 Instruments and controls www.homelink.com or call 1-800-355- 3515. Note the following information about this system. If your vehicle is equipped with the HomeLink Wireless Control System, it ® complies with Part 15 of the Federal Communications Commission Rules in the U.S.
Page 152 HomeLink button 1 ® HomeLink button 2 ® HomeLink button 3 ® 2. Press and hold the two outer HomeLink buttons (button 1 and button ® 3) until the indicator light begins to flash (after approximately 20 seconds). Then release both buttons. 3.
Page 153 3-42 Instruments and controls tion manual. Training button 2. Press the training button on the garage door opener motor head unit (which activates the “training light” on the unit). Proceed to step 3 within 30 seconds. 3. Inside the vehicle, firmly press, hold for 2 seconds and release the HomeLink button that was programmed in the pre- vious section.
Page 154 6. When the indicator light flashes slowly and then rapidly after several seconds, release both buttons. 7. Plug the motor of the entrance gate/ garage door opener to the outlet. 8. Test your entrance gate/garage door opener by pressing the programmed HomeLink button.
Page 155: Outside Mirrors
3-44 Instruments and controls & Outside mirrors ! Remote control mirror switch Selection switch Direction control switch The remote control mirrors operate only when the ignition switch is in the “ON” or “Acc” position. 1. Press either end of the selection switch, “L”...
Page 156: Defogger And Deicer
Defogger and deicer Rear window defogger Outside mirror defogger (if equipped) Windshield wiper deicer (if equipped) The vehicle is equipped with a rear window defogger. For some models, the outside mirror defogger and/or windshield wiper deicer are/is also equipped. The defogger and deicer system is activated only when the ignition switch is in the “ON”...
Page 157 . Models with genuine SUBARU navi- gation system: The settings can be changed for the continuous operation mode using the navigation monitor.
Page 158: Tilt/Telescopic Steering Wheel
Tilt/telescopic steering wheel WARNING . Do not adjust the steering wheel tilt/telescopic position while driv- ing. This may cause loss of vehicle control and result in personal injury. . If the lever cannot be raised to the fixed position, adjust the steering wheel again.
Page 159 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 160 Ventilator... Airflow selection ... Center and side ventilators ... Manual climate control system (if equipped) ... Control panel ... Heater operation ... Air conditioner operation... Automatic climate control system (if equipped) ... Type A ... Type B ... Temperature sensors... Operating tips for heater and air conditioner ...
Page 161: Climate Control
Climate control Ventilator & Airflow selection...
Page 162: Center And Side Ventilators
& Center and side ventilators ! Center ventilators Move the tab to adjust the flow direction. ! Side ventilators Open Close Thumb-wheel Move the tab to adjust the flow direction. To open or close the ventilator, turn the thumb-wheel up or down. Climate control Manual climate control sys- tem (if equipped)
Page 163: Air Inlet Selection Button
Climate control ! Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select four fan speeds. ! Airflow control dial Each dial position activates the following air outlets.
Page 164: Heater Operation
Place the air inlet selection button to the OFF position when the interior has cooled to a comfortable temperature and the road is no longer dusty. WARNING Continued operation with the air inlet selection button in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.
Page 165 Climate control ! Heating To direct warm air toward the floor: 1. Set the air inlet selection button to the OFF position. 2. Set the airflow control dial to the “ position. 3. Set the temperature control dial to the most comfortable level.
Page 166: Air Conditioner Operation
WARNING Continued operation with the air inlet selection button in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears. & Air conditioner operation ! Cooling or dehumidifying ON position For cooling and dehumidification of the passenger compartment, performing the following steps will allow air to flow...
Page 167: Automatic Climate Control System (If Equipped)
Climate control Automatic climate control system (if equipped) NOTE Operate the automatic climate control system when the engine is running. & Type A NOTE The blower fan rotates at a low speed when the engine coolant temperature is low. For efficient defogging or dehumi- difying in cold weather, press the “A/C”...
Page 168 ! Control panel Climate control Temperature control dial (driver’s side) AUTO button DUAL mode button OFF button Air inlet selection button Fan speed control button Airflow mode selection button Air conditioner button Temperature control dial (front passen- ger’s side) 10) Defroster button 11) Rear window defogger button (Refer to “Defogger and deicer”...
Page 169: Auto Button
4-10 Climate control ! AUTO button FULL AUTO mode operation: When the “AUTO” button is pressed, the indicator light “FULL AUTO” on the display illuminates. In this state, fan speed, airflow distribution, air-inlet control, and air con- ditioner compressor operation are auto- matically controlled.
Page 170 ! DUAL mode It is possible to make separate tempera- ture settings for the driver’s side and passenger’s side (DUAL mode). To activate the DUAL mode: Press the “DUAL” button. When the DUAL mode is activated, the indicator light on the “DUAL”...
Page 171: Airflow Mode Selection Button
4-12 Climate control ! A/C – Air conditioner button If the windshield starts to fog when the climate control system is operated in the AUTO mode, press the air conditioner button “A/C” to defog and dehumidify. When this button is pressed, the air conditioner compressor turns on and the indicator light “A/C”...
Page 172: Type B
! Air inlet selection button Select airflow by pressing the air inlet selection button. The selected air inlet setting is shown on the control panel. (Recirculation): Interior air recircu- lates inside the passenger compartment. Use this position when quickly cooling down the passenger compartment or to prevent outside air from entering the passenger compartment.
Page 173 SUBARU recom- mends using the AUTO position. Other positions: The fan speed can be adjusted in 7 steps.
Page 174 AUTO: The airflow control is adjusted automatically in accordance with the air temperature inside and outside the pas- senger compartment, the intensity of sun- light, and other factors. SUBARU recom- mends using the AUTO position. (Ventilation): Instrument panel outlets (Bi-level): Instrument panel outlets and...
Page 175 To return to “AUTO” mode, turn the fan speed control dial or airflow control dial to a position other than the AUTO position. Then turn to “AUTO” mode. SUBARU recommends using the AUTO position. WARNING Continued operation in the ON posi- tion may fog up the windows.
Page 176: Temperature Sensors
& Temperature sensors Interior air temperature sensor Solar sensor The automatic climate control system employs several sensors. These sensors are delicate. If they are not treated properly and become damaged, the sys- tem may not be able to control the interior temperature correctly.
Page 177: Lubrication Oil Circulation In The Refrigerant Circuit
Under extremely dusty conditions, the filter should be replaced more frequently. It is recommended that you have your filter checked or replaced by your SUBARU dealer. For replacement, use only a genuine SUBARU air filter kit. Replacement schedule:...
Page 178: Replacing An Air Filter
mance if not properly maintained. & Replacing an air filter 1. Remove the glove box. (1) Open the glove box. (2) Remove the damper shaft from the glove box. (3) Pull out the glove box. 2. Remove the air filter. 4-19 Climate control 3.
Page 179 4-20 Climate control 4. Reinstall the glove box, and connect the damper shaft. 5. Close the glove box. 6. LABEL installation (1) Fill out the information on the service label (small). Service label (2) Attach the service label to the driver’s side door pillar.
Page 180: Audio
Antenna system ... Roof antenna ... FM reception ... Installation of accessories... Audio set ... Type A audio set (if equipped) ... Type B audio set (if equipped) ... Type C audio set (if equipped) ... Type D audio set (if equipped) ... Power and audio controls ...
Page 181 Audio Random playback ... SCAN (only when connecting USB storage device)... Selecting category (only when connecting ® iPod ) ... Display selection... Folder selection (only when connecting USB storage device) ... Setting the playing speed (only when the audiobook is playing) (type D audio)... When the following messages are displayed ...
Page 182: Antenna System
Antenna system & Roof antenna CAUTION . Be sure to lower the antenna rod before entering garages, parking towers and other locations with low ceilings. . Remove the antenna rod before washing your car at a car wash. If the antenna rod is left attached, it may scratch the roof.
Page 183: Installation Of Accessories
Audio set Your SUBARU may be equipped with one of the following audio sets. Refer to the pages indicated in this section for operat- ing details.
Page 184: Type A Audio Set (If Equipped)
Audio & Type A audio set (if equipped) The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. . Power and audio controls: refer to page . Radio operation: refer to page 5-13 .
Page 185: Type B Audio Set (If Equipped)
Audio & Type B audio set (if equipped) The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. . Power and audio controls: refer to page . Radio operation: refer to page 5-13 .
Page 186: Type C Audio Set (If Equipped)
Audio & Type C audio set (if equipped) The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. . Power and audio controls: refer to page . Radio operation: refer to page 5-13 .
Page 187: Type D Audio Set (If Equipped)
Audio & Type D audio set (if equipped) The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. . Power and audio controls: refer to page . Radio operation: refer to page 5-13 .
Page 188: Power And Audio Controls
Power and audio controls & Power switch and volume control Type A and B audio Type C and D audio The dial is used for both power (ON/OFF) and volume control. The radio is turned ON and OFF by pushing the dial, and the volume is controlled by turning the dial.
Page 189 5-10 Audio ! Tone and balance control (type A, B and C audio) Type A and B audio Type C audio Each brief press of the “TUNE/TRACK/ CH” dial changes the control modes in the following sequence. Choose the preferred level for each mode by turning the “TUNE/TRACK/CH”...
Page 190 First menu Second menu Third menu Screen — — Sound Tone Bass Treble Balance Balance Fader — — SRS Sound — Screen Brightness — Contrast — Screen Size Screen Saver Picture Select Picture Down- load Picture Erase BT Audio Pair Audio —...
Page 191 5-12 Audio ! Adjustable level of each mode Mode Volume Volume control AUX volume control* Tone and balance Bass control Midrange control Treble control Balance Fader Other settings SPEED VOLUME BEEP (Type A, B and C audio) OFF to ON CS Auto (Type B audio) SRS Sound (Type D audio) Brightness (Type D audio)
Page 192: Fm/Am Radio Operation
FM/AM radio operation & FM/AM selection Type A and B audio Type C and D audio Push the “FM/AM” button when the radio is off to turn on the radio. Push the “FM/AM” button when the radio is on to select the reception. Each brief press of the “FM/AM”...
Page 193 5-14 Audio however, when radio signals are weak. In such a situation, perform manual tuning to select the desired station. ! Scan tuning (SCAN) Type A and B audio Type C audio Type D audio If you press the “SCAN” button briefly (type A, B and C audio)/continuously (type D audio), the radio will switch to the scan mode.
Page 194: Radio) (Type D Audio)
In the PTY selection mode, when the preferred PTY group has been selected, pressing the “SEEK” button “ ” or “ seeks within that PTY group. The control function returns to the normal mode after approximately 10 seconds. ! Seek in PTY (Program type) group (type D audio) In the PTY selection mode, when the preferred PTY group has been selected,...
Page 195: Displaying Radio Ps (Program Service Name) And Rt (Radio Text)
5-16 Audio . The “LIVE” indicator illuminates while the “Ballgame” is received. . The “STEREO” indicator illuminates while the FM stereo broadcast is received. . The “PTY” indicator illuminates during the PTY selection mode. ! About HD Radio NOTE . HD Radio Technology is a hybrid broadcasting system that employs di- gital and analog signals.
Page 196: Station Preset
& Station preset ! How to preset stations 1. Press the “FM/AM” button to select FM1, FM2, FM3 (type A, B and C audio)/ FM-AS (type D audio), AM or AM-AS (type D audio) reception. 2. Select the preferred station. 3.
Page 197: Satellite Radio Operation (If Equipped)
5-18 Audio Satellite radio operation (if equipped) To receive satellite radio, it is necessary to install the SUBARU genuine satellite receiver (optional equipment) and to enter into a contract. For details, please contact your SUBARU dealer. & XM satellite radio (U.S.A.
Page 198: Displaying Satellite Radio Id Of Tuner
signals can be blocked by objects such as buildings, but the network of repeater stations allows signal coverage within urban areas such as cities. You may experience problems in receiving satellite radio signals in the follow- ing situations. . If you are driving northward in a coastal area Because the satellite radio antenna is located on the windshield, the signal...
Page 199: Band Selection
5-20 Audio & Band selection Type A and B audio Type C audio Type D audio Push the “SAT” button when the radio is off to turn on the radio. Push the “SAT” button when the radio is on to select SAT1, SAT2 or SAT3 recep- tion.
Page 200: Channel Preset
When in the category search mode, press the following button to change the cate- gory up or down. Type A and B audio: Category up by one step Category down by one step Type C audio: Category up by one step Category down by one step...
Page 201: Display Selection (Type A, B And C Audio)
5-22 Audio occurs, it is necessary to reset the preset buttons. ! Selecting preset channels 1. Press the “SAT” button to select SAT1, SAT2 or SAT3 reception. 2. Press the preferred preset button briefly. ! Displaying and selecting preset stations (type D audio) 1.
Page 202: Play File
– Maximum number of files on a CD: 510 (type A, B and C audio)/999 (type D audio) & Play file NOTE . Copyright protected MP3/WMA/AAC files will not be played by the system. The player will automatically skip to the next file (track).
Page 203: How To Play Back A Cd
5-24 Audio ! Inserting a disc in a desired posi- tion 1. Briefly press the button. If the magazine in the player has an idle position where you can insert a disc, the disc number indicator associated with the idle position will blink. The positions in the magazine the indica- tor of which steadily lights up are already loaded with discs.
Page 204: To Select A Track From Its Beginning
& To select a track from its beginning Type A and B audio Type C and D audio Turn the “TUNE/TRACK/CH” dial clock- wise to skip to the beginning of the next track/file. Each time the dial is turned, the indicated track/file number will increase.
Page 205: Repeating
5-26 Audio & Repeating To repeat a track/file, briefly press the following button (repeat button) while the track/file is playing. Type A and B audio Type C audio Type D audio Each time you briefly press the button, the mode changes in the following se- quences.
Page 206: Scan (Type A, B And C Audio)
Type A audio: Type B audio: Type C audio: Type D audio: NOTE . The “RDM” (type A, B and C audio)/ “Track RDM” (type D audio) indication refers to the random playback of the tracks. It randomly repeats the tracks on the CD.
Page 207: Display Selection (Type A, B And C Audio)
5-28 Audio . Turn off the power of the audio equipment . Turn the ignition switch to the “LOCK” position & Display selection (type A, B and C audio) Type A and B audio Type C audio If you press the “TEXT” button during playback, the display will change as shown in the following sequence.
Page 208: How To Eject A Cd From The Player (Type A, C And D Audio)
CD player, determine the cause based on the follow- ing information. If you cannot clear those messages, please contact your SUBARU dealer. ! When “PUSH EJECT” is displayed Press the eject button to unload the disc.
Page 209: Auxiliary Input Jack (If Equipped)
5-30 Audio will be displayed. If the disc cannot be unloaded or this message remains dis- played, please contact your SUBARU dealer. ! When “CHECK DISC” is displayed Press the eject button to unload the discs. Check that the disc is not damaged or scratched, and also check that the disc is inserted correctly.
Page 210: Precautions To Observe When Handling A Compact Disc
device. To avoid a large volume differ- ence, turn down the volume when you change between portable audio players. . In some cases, when the sound volume of the portable audio player is low, the sound becomes bad when you turn up the volume of the vehicle audio system.
Page 211 5-32 Audio . You cannot use a DualDisc in the CD player. If you insert a DualDisc into the player, the disc may not come out again, possibly causing the player to malfunction. . In cold and/or rainy weather, dew can form inside the CD player, preventing normal operation.
Page 212: Play File
® USB storage device / iPod operations (type C and D audio) & Play file Refer to “Play file” F5-23. & Connectable USB storage device Mass storage class USB memory can be connected. USB storage devices that can be played back are accompanied by the following restrictions.
Page 213: Connecting Usb Storage Device / Ipod
5-34 Audio Type D audio: Model Firmware version classic 2.0.4 nano 1.3.1 nano 2G 1.1.3 ® iPod nano 3G 1.1.3 nano 4G 1.0.4 touch 3.1.3 touch 2G 3.1.3 3.1.3 ® iPhone 3.1.3 3.1.3 3G S CAUTION ® Do not connect an iPod other than the previously stated models.
Page 214: How To Play Back
® Guide that comes with the iPod . If an iPod ® and the connection cable are connected improperly, the iPod cannot be powered on or will not be recognized by in-vehicle equipment. In this case, disconnect the connection ® cable from the iPod , and then connect it again.
Page 215: Repeating
5-36 Audio ends and play begins from the begin- ning of the index. & Repeating ! When connecting USB storage de- vice Repeating is operated in the same way a CD is played. For details, refer to “Re- peating” F5-26. ! When connecting iPod ®...
Page 216: Scan (Only When Connecting Usb Storage Device)
. The “ALBUM RDM” indication refers to the shuffle playback of the album. It sequentially plays back all of the indexes in the album. . The “SONG RDM” indication refers to the shuffle playback in the entire ® iPod . It randomly repeats all of the ®...
Page 217: When The Following Messages Are Displayed
® rage device/iPod , determine the cause based on the following information. If you cannot clear those messages, please contact your SUBARU dealer. ! When “CHECK DEVICE” is dis- played This message is displayed under the following conditions. . When there is a short in the USB bus .
Page 218: And " " Buttons
Models with Hands-free system The “MODE” button is used to select the desired audio mode. Each time it is pressed, the mode changes to the next one in the following sequence: Type A and B audio: Type C and D audio: *1: The frequency last received in the selected waveband will be displayed.
Page 219: Volume Control Buttons
5-40 Audio ! With radio mode selected Press the “ ” button or “ ” button briefly. The radio will seek the next preset station and stop on it. Press the “ ” button or “ ” button continuously. The radio will seek the next receivable station and stop on it.
Page 220: Mute Button (Models Without Hands-Free System)
& MUTE button (models with- out Hands-free system) Press the “ ” button if you wish to immediately cut the volume to zero. The audio display will show “MUTE”. If you press the button again, the original sound volume will return and “MUTE” turns off.
Page 221 5-42 Audio audio) menu. If no devices are registered, “EMPTY” is displayed and the mode ® changes to the Bluetooth audio setting mode. 2. Select the “CONFIRM” menu. If the device is connected, “SELECTED” is displayed and the selecting procedure is finished.
Page 222: Hands-Free System (If Equipped)
Hands-free system (if equipped) NOTE . For models with the genuine SUBARU navigation system, refer to the Owner’s Manual supplement for the navigation system. . When selling your vehicle, make sure that you initialize the Hands-free system to prevent personal data from being improperly accessed.
Page 223: Certification For The Hands-Free System
5-44 Audio volume may be different from those of cell phones currently used. . When the ignition switch is turned to the “LOCK” position during a call, the call may be disconnected or continued on the cell phone depending on the type of cell phone that is used.
Page 224: Safety Precautions
equipment and receiver. . Connect the equipment into an out- let on a circuit different from that to which the receiver is connected. . Consult the dealer or an experi- enced radio/TV technician for help. . Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip-...
Page 225: Using The Hands-Free System
5-46 Audio used by a movable body identifi- cation device. & Using the Hands-free system ! Turning on/off the Hands-free mode OFF hook switch ON hook switch Talk switch To turn on the Hands-free mode, press the OFF hook switch .
Page 226 First menu Second menu PHONE BOOK* ADD ENTRY BY VOICE BY PHONE MANUAL INPUT CALL HISTORY GO BACK LIST NAMES CHANGE NAME SET SPD DIAL/SET SPEED DIAL DELETE ENTRY DEL SPD DIAL/DE- LETE SPEED DIAL GO BACK REDIAL DIAL STORE DELETE GO BACK DIAL...
Page 227 5-48 Audio First menu Second menu SETUP SECURITY PHONE SETUP SYSTEM SETUP GO BACK *: If a PIN code is not registered, the menu described in the chart is not available. Third menu SET PIN Setting a PIN code PHBK LOCK*/ PHONE BOOK Locking the phonebook LOCK*...
Page 228: Voice Command System
! Voice command system OFF hook switch ON hook switch Talk switch To turn on the voice command system, press the talk switch briefly. To turn off the voice command system, wait for 5 seconds without using the voice command system.
Page 229 5-50 Audio security sécurité jumeler le télé- pair phone phone change name modifier le nom sélectionner le tél- select phone éphone lister les télé- list phones phones configurer le set pass key passe-partout add entry ajouter l’entrée delete entry supprimer l’entrée supprimer compo- delete speed dial sition abrégée...
Page 230 “GO BACK” (type C audio)/“BS” (type D audio) is chosen using the “TUNE/ TRACK/CH” dial, the character that was input last is deleted. ! Registering from call history 1. Select the “CALL HISTORY” menu. 2. Select “OUTGOING” or “INCOMING” by operating the “TUNE/TRACK/CH” dial. 3.
Page 231 5-52 Audio the OFF hook switch is pushed, the selected number is called. . After “LIST NAMES” is selected, if no operation is performed, the mem- ories are displayed and voice tags are spoken. After all memories/voice tags are displayed/spoken, “END OF LIST” is displayed and the mode changes to the “PHONE BOOK”...
Page 232 ! Making a phone call by saying number 1. Select the top menu (phone menu). 2. Press the talk switch 3. Say “DIAL BY NUMBER”. 4. Press the talk switch again. 5. Say the desired phone number to be called. 6.
Page 233: Bluetooth Setting
5-54 Audio ! Adjustable level of each volume Volume Range Initial setting Phone call 0 to 14 Voice 0 to 14 Voice guidance 0 to 6 & Bluetooth ® setting ! Security setting ! Setting PIN code The PIN code is a 4-digit number and is used when locking the phonebook.
Page 234 voice tag. 3. Register the voice tag. For details, refer to “Preparation for using the Hands- free system” F5-46. ! List phones function The cell phone voice tags saved in the cell phone list are spoken by using the list phones function.
Page 235: Screensaver (Type D Audio)
5-56 Audio Screensaver (type D audio) If the following operations are not per- formed for more than 30 seconds while the audio is ON, the screensaver will be displayed. . Operate any button or dial . Shift the shift lever/select lever to the “R”...
Page 236: Erasing Picture
5-57 Audio & Erasing picture 1. Select the “Picture Erase” menu by operating the “TUNE/TRACK/CH” dial. For details, refer to “Audio settings (type D audio)” F5-10. If no pictures are saved, “No Data” is displayed. Press the button to return to the “Screen Saver” mode.
Page 237 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 238 Interior lights ... Dome light ... Cargo area light ... Map light... Sun visors ... Vanity mirror ... Storage compartment ... Glove box ... Center console... Overhead console ... Rear seat center table (if equipped) ... Coin tray... Cup holders ... Front passenger cup holder...
Page 239: Interior Equipment
The setting can be changed using the navigation monitor. For details, please refer to the Owner’s Manual supplement for the navigation system. Also, the setting can be changed by a SUBARU dealer. Contact your SUBARU dealer for details. . Models without genuine SUBARU navigation system: The setting can be changed by a SUBARU dealer.
Page 240: Cargo Area Light
& Cargo area light DOOR The cargo area light switch has the following positions. DOOR: The light illuminates when the rear gate is opened. The light remains illumi- nated for several seconds and turns off after the rear gate is closed. OFF: The light remains off.
Page 241: Sun Visors
The setting can be changed using the navigation monitor. For details, please refer to the Owner’s Manual supplement for the navigation system. Also, the setting can be changed by a SUBARU dealer. Contact your SUBARU dealer for details. . Models without genuine SUBARU navigation system: The setting can be changed by a SUBARU dealer.
Page 242: Vanity Mirror
& Vanity mirror CAUTION Keep the vanity mirror cover closed while the car is being driven to avoid being temporarily blinded by the glare of bright light. To use the vanity mirror, swing down the sun visor and open the vanity mirror cover. Storage compartment CAUTION .
Page 243 Interior equipment To use as an armrest: 1. Tip the console top forward from its vertical position. 2. Push the armrest part of the console top forward to the desired position. Adjust the position of the armrest to suit your driving position.
Page 244: Overhead Console
& Overhead console To open the console, push on the console lid lightly and the lid will automatically open. CAUTION When your vehicle is in the sun or on a warm day, the inside of the overhead console heats up. Avoid storing plastic or other heat-vulner- able or flammable articles such as a lighter in the overhead console.
Page 245: Cup Holders
Interior equipment Cup holders CAUTION Take care to avoid spills. Beverages, if hot, might burn you or your passengers. Spilled beverages may also damage upholstery, carpets or audio equipment. & Front passenger cup holder CAUTION Do not pick up a cup from the cup holder or put a cup in the holder while you are driving, as this may distract you and lead to an accident.
Page 246: Bottle Holders
Bottle holders CAUTION . Do not pick up a bottle from the bottle holder or put a bottle in the holder while you are driving, as this may distract you and lead to an accident. . When placing a beverage in a door pocket, make sure it is capped.
Page 247: Use With A Cigarette Lighter (Dealer Option)
To use the accessory power outlet as a cigarette lighter socket, purchase the cigarette lighter plug, which is an optional accessory. A cigarette lighter plug is available from your SUBARU dealer. The cigarette lighter operates only when the ignition switch is in the “ON” or “Acc” position.
Page 248: Ashtray (If Equipped)
To use the cigarette lighter, push in the knob and wait a few moments. It will automatically spring up when ready for use. WARNING To avoid being burned, never grasp the lighter by the end with the heating element. Doing so could result in injury and could also damage the heating element.
Page 249: Floor Mat
6-12 Interior equipment The portable ashtray can be installed in each cup holder. For the locations of the cup holders, refer to “Cup holders” F6-8. When using the ashtray, open the lid of the ashtray. When removing the ashtray from a cup holder, pull the ashtray upwards.
Page 250: Shopping Bag Hook
Shopping bag hook CAUTION Do not hang items on the shopping bag hook that weigh 6 lbs (3 kg) or more. A shopping bag hook is attached to each side of the cargo area. Coat hook A coat hook is attached to each side of the cargo area.
Page 251: To Remove The Cover
6-14 Interior equipment Install the front cover behind the rear seatback. WARNING Do not place anything on the ex- tended cover. Putting excessive weight on the extended cover can break it and an object on the cover could tumble forward in the event of a sudden stop or collision.
Page 252: To Install The Cover Housing
& To install the cover housing 1. Remove the cover of the retainers by prying on the edge with a flat-head screwdriver. 2. Insert the projections located on the both ends of the sleeve into the recesses of the retainers. 6-15 Interior equipment Cargo tie-down hooks...
Page 253: Under-Floor Storage Compartment (If Equipped)
6-16 Interior equipment CAUTION The cargo tie-down hooks are de- signed only for securing light cargo. Never try to secure cargo that exceeds the capacity of the hooks. The maximum load capacity is 44 lbs (20 kg) per hook. Under-floor storage compart- ment (if equipped) The storage compartment is located under the floor of the cargo area, and it can be...
Page 254: Rear View Camera (If Equipped)
. Do not disassemble or modify the camera, switch or wiring. If smoke comes out or you smell a strange odor, stop using the rear view camera immediately. Contact your SUBARU dealer for an inspection. Continued use may result in accident, fire or electric shock. CAUTION .
Page 255: How To Use The Rear View Camera
2. Set the shift lever or select lever to “R”. NOTE . For models with the genuine SUBARU navigation system, the image of the rear view camera has priority over other screen displays. Therefore, while the rear view camera is in opera- tion, the operations of other screens are disabled.
Page 256 Image from camera The area from the rear end of the bumper can be viewed. Areas at both ends of the bumper and areas just under the bumper cannot be viewed. Also, the image from the rear view camera looks shorter than the actual distance. CAUTION The range that can be viewed with the rear view camera is limited.
Page 257: Help Line
6-20 Interior equipment & Help line The help line (distance marker and vehicle width line) is a guide to help you realize the actual distance from the screen. Vehicle width line (oblique vertical line) Approx. 10 feet (3 m) from the bumper (green horizontal line) Approx.
Page 258 ! When there is a downward slope at the back 3 feet (1 m) The distance on the screen looks nearer than the actual distance. NOTE When cargo is loaded, the rear view distance on the screen looks farther than the actual distance as in an upward slope.
Page 259 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 260: Starting And Operating
Fuel ... Fuel requirements ... Fuel filler lid and cap... State emission testing (U.S. only)... Preparing to drive ... Starting the engine... MT models ... AT models... Stopping the engine... Remote engine start system (dealer option) ... Starting your vehicle ... Remote start safety features ...
Page 261: Starting And Operating
Do not be concerned if your vehicle sometimes knocks lightly when you drive up a hill or when you accelerate. Contact your SUBARU dealer if you use a fuel with the specified octane rating and your vehicle knocks heavily or persistently.
Page 262: Fuel Filler Lid And Cap
SUBARU. In addition, some gasoline suppliers are now producing reformulated gasolines, which are designed to reduce vehicle emissions. SUBARU approves the use of reformulated gasoline. If you are not sure what the fuel contains, you should ask your service station...
Page 263 Starting and operating 1. To open the fuel filler lid, pull the lid release lever up. The lever is on the floor at the left of the driver’s seat. WARNING Before opening the fuel filler cap, first touch the vehicle body or a metal portion of the fuel pump or similar object to discharge any static electricity that may be present...
Page 264 Starting and operating spilled fuel is not covered under the SUBARU Limited Warranty. . Always use a genuine SUBARU fuel filler cap. If you use the wrong cap, it may not fit or have proper venting and your fuel tank and emission control system may be damaged.
Page 265: State Emission Testing (U.s. Only)
State emission testing (U.S. only) At state inspection time, remember to tell your inspection or service station in advance not to place your SUBARU AWD vehicle on a two-wheel dynam- ometer. Otherwise, serious transmis- sion damage will result. Some states have started using dynam-...
Page 266: Preparing To Drive
. Owners of rejected or failing vehicles should contact their SUBARU Dealer for service. Preparing to drive You should perform the following checks and adjustments every day before you start driving.
Page 267: At Models
“START” position without depressing the accelerator pedal. (4) If the engine still refuses to start, contact your nearest SUBARU dealer for assistance. 6. Confirm that all warning and indicator lights have turned off after the engine has started.
Page 268: Stopping The Engine
engine warms up. While the engine is warming up, make sure that the select lever is at the “P” or “N” position and that the parking brake is applied. CAUTION If you restart the engine while the vehicle is moving, shift the select lever into the “N”...
Page 269: Starting Your Vehicle
7-10 Starting and operating & Starting your vehicle The remote control start system is acti- vated by pressing the “ ” button twice within 3 seconds on your remote control transmitter. The system will check certain pre-conditions before starting, and if all safety parameters are correct, the engine will start within 5 seconds.
Page 270: Pre-Heating Or Pre-Cooling The Interior Of The Vehicle
transmitter within a few seconds immedi- ately following remote engine start shut- down. & Pre-heating or pre-cooling the interior of the vehicle Before exiting the vehicle, set the tem- perature controls to the desired setting and operation. After the system starts the vehicle, the heater or air-conditioning will activate and heat or cool the interior to your setting.
Page 271: System Maintenance
7-12 Starting and operating Pressing the brake pedal repeatedly will toggle the feature ON or OFF each time. 7. To exit the remote transmitter and feature programming mode, turn the igni- tion switch to the “LOCK” position, remove the key from the ignition switch and test operation of the remote transmitter(s) and horn confirmation feature.
Page 272: Manual Transmission
2. Remove the circuit board from the bottom half of the case and slide the white plastic battery holder out from under the battery tab releasing the batteries. Re- move the old batteries and replace with new ones. Be sure to observe the (+) sign on the old batteries before removing them to ensure that the new batteries are inserted properly (battery “+”...
Page 273: Shifting Speeds
7-14 Starting and operating WARNING . Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either of these condi- tions and the risk of an accident is consequently increased.
Page 274: Automatic Transmission
speed due to slow traffic, turning corners, or driving up steep hills, downshift to a lower gear before the engine starts to labor. On steep downgrades, downshift the transmission to 4th, 3rd or 2nd gear as necessary; this helps to maintain a safe speed and to extend brake pad life.
Page 275: Select Lever
7-16 Starting and operating allow the transmission to shift at the most appropriate times for the current condition of your vehicle. Optimized shifting will be restored as the vehicle continues to be driven for a while. & Select lever : Shifting is possible with the brake pedal depressed.
Page 276: Shift Lock Function
! D (Drive) This position is for normal driving. The transmission automatically shifts into a suitable gear from 1st to 4th according to the vehicle speed and the acceleration you require. When more acceleration is required in this position, depress the accelerator pedal fully to the floor and hold that position.
Page 277 If you must perform the above procedure, the shift lock system (or the vehicle control system) may be malfunctioning. Contact a SUBARU dealer for an inspection as soon as possible. If the select lever does not move after performing the above procedure, refer to “Shift lock release using the shift lock...
Page 278: Selection Of Manual Mode
& Selection of manual mode With the vehicle either moving or station- ary, move the select lever from the “D” position to the manual gate then move it to the “+” end or “−” end of the manual gate to select manual mode. Type A Type B Upshift indicator...
Page 279: Driving Tips
7-20 Starting and operating end of the manual gate. Shift to the next-lower gear by briefly pulling the select lever toward the “−” end of the manual gate. NOTE Please read the following points care- fully and bear them in mind when using the manual mode.
Page 280: Power Steering
Type A Type B When selected, the SPORT mode indica- tor light on the combination meter will turn To deselect SPORT mode, move the select lever to the “D” position or select manual mode. To subsequently reselect SPORT mode, move the select lever to the “D” position and from there to the manual gate.
Page 281: Braking
7-22 Starting and operating Braking & Braking tips WARNING Never rest your foot on the brake pedal while driving. This can cause dangerous overheating of the brakes and needless wear on the brake pads and linings. ! When the brakes get wet When driving in rain or after washing the vehicle, the brakes may get wet.
Page 282: Disc Brake Pad Wear Warning Indicators
If a squeaking or scraping noise is heard from the disc brakes while braking, im- mediately have your vehicle checked by your SUBARU dealer. ABS (Anti-lock Brake Sys- tem) The ABS system prevents the lock-up of...
Page 283: Electronic Brake Force Distribution (Ebd) System
3. Release the parking brake. If both warning lights turn off, the EBD system may be malfunctioning. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights illuminate again and stay illuminated after the engine has...
Page 284: Vehicle Dynamics Control System
5. If the brake fluid level is not below the “MIN” mark, the EBD system may be malfunctioning. Drive carefully to the nearest SUBARU dealer and have the system inspected. 6. If the brake fluid level is below the “MIN” mark, DO NOT drive the vehicle.
Page 285: Vehicle Dynamics Control System Monitor
7-26 Starting and operating trol system is reduced and this should be taken into ac- count when driving the vehi- cle in such a condition. . If non-matching tires are used, the Vehicle Dynamics Control system may not operate cor- rectly.
Page 286: Vehicle Dynamics Control Off Switch
& Vehicle Dynamics Control OFF switch Pressing the switch to deactivate the Vehicle Dynamics Control system can facilitate the following operations: . a standing start on a steeply sloping road with a snowy, gravel-covered, or otherwise slippery surface . extrication of the vehicle when its wheels are stuck in mud or deep snow When the switch is pressed during engine operation, the Vehicle Dynamics Control...
Page 287: Tire Pressure Monitoring System (Tpms) (U.s.-Spec. Models)
1 minute. This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU...
Page 288: Parking Your Vehicle
If the light illuminates steadily after blinking for approximately 1 minute, promptly contact a SUBARU dealer to have the system inspected. CAUTION . Do not place metal film or any metal parts in the cargo room.
Page 289: Parking Tips
7-30 Starting and operating CAUTION Never drive while the parking brake is set because this will cause un- necessary wear on the brake lin- ings. Before starting to drive, always make sure that the parking brake has been fully released. &...
Page 290: Hill Start Assist System (Mt Models)
alone to hold the vehicle. . If your vehicle has a front under- spoiler and rear underspoiler (if equipped), pay attention to blocks and other obstructions on the ground when parking. The underspoilers could be da- maged by contact with them. Hill start assist system (MT models) CAUTION...
Page 291: Hill Start Assist Warning Light
7-32 Starting and operating The Hill start assist system does not operate when the vehicle is facing down- hill. And the Hill start assist system may not operate on slight grades. When starting in reverse and using the Hill start assist system, a braking effect may be felt even after the brake pedal has been released.
Page 292: To Set Cruise Control
. towing a trailer & To set cruise control 1. Push the “CRUISE” main switch but- ton. Type A Type B The cruise control indicator light on the combination meter will illuminate. 2. Depress the accelerator pedal until the vehicle reaches the desired speed. 7-33 Starting and operating 3.
Page 293: To Temporarily Cancel The Cruise Control
7-34 Starting and operating Type B At this time, the cruise control set indicator light on the combination meter will illumi- nate. The vehicle will maintain the desired speed. Vehicle speed can be temporarily in- creased while driving with the cruise control activated.
Page 294: To Change The Cruising Speed
& To change the cruising speed ! To increase the speed (by button) Push the “RES/ACC” button and hold it until the vehicle reaches the desired speed. Then, release the button. The vehicle speed at that moment will be memorized and treated as the new set speed.
Page 295: Cruise Control Indicator Light
7-36 Starting and operating button once. Now the desired speed is set and the vehicle will keep running at that speed without depressing the accelerator pedal. & Cruise control indicator light Refer to “Cruise control indicator light” F3-25. & Cruise control set indicator light Refer to “Cruise control set indicator light”...
Page 296: Driving Tips
New vehicle break-in driving – the first 1,000 miles (1,600 km) ... Fuel economy hints ... Engine exhaust gas (carbon monoxide)... Catalytic converter ... Periodic inspections ... Driving in foreign countries ... Driving tips for AWD models... On-road and off-road driving... Winter driving ...
Page 297: New Vehicle Break-In Driving - The First 1,000 Miles (1,600 Km)
Driving tips New vehicle break-in driving – the first 1,000 miles (1,600 The performance and long life of your vehicle are dependent on how you handle and care for your vehicle while it is new. Follow these instructions during the first 1,000 miles (1,600 km): .
Page 298: Catalytic Converter
(misfiring, back- firing or incomplete combustion), have your vehicle checked and repaired by an authorized SUBARU dealer. . Do not apply undercoating or rust prevention treatment to the heat shield of catalytic converter and the exhaust sys- tem.
Page 299: Periodic Inspections
Driving tips operates at very high tempera- tures. . Keep everyone and flammable materials away from the exhaust pipe while the engine is running. The exhaust gas is very hot. Periodic inspections To keep your vehicle in the best condition at all times, always have the recom- mended maintenance services listed in the maintenance schedule in the “War-...
Page 300: Driving Tips For Awd Models
By shifting power between the front and rear wheels, SUBARU AWD can also provide added traction during acceleration and added engine braking force during deceleration.
Page 301: On-Road And Off-Road Driving
If you do take your SUBARU off-road, certain common sense precautions such as those in the following list should be taken. . Make certain that you and all of your passengers are wearing seatbelts.
Page 302 “Warranty and Mainte- nance Booklet”. Remember that damage done to your SUBARU while operating it off-road and not using common sense precautions such as those listed above is not eligible for warranty coverage.
Page 303: Winter Driving
Do not use engine antifreeze or other substitutes because they may damage the paint of the vehicle. SUBARU Windshield Washer Fluid con- tains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing tem- perature varies according to how much it is diluted, as indicated in the following table.
Page 304: Driving On Snowy And Icy Roads
Driving tips If your SUBARU is not going to be used for an extended period, it is best to have the fuel tank filled to capacity. & Driving on snowy and icy...
Page 305: Corrosion Protection
8-10 Driving tips roads. This may cause loss of vehicle control. CAUTION Avoid prolonged continuous driving in snowstorms. Snow will enter the engine’s intake system and may hinder the airflow, which could re- sult in engine shutdown or even breakdown. ! Wiper operation when snowing Before driving in cold weather, make sure the wiper blades are not frozen to the...
Page 306: Tire Chains
tions may result in severe me- chanical damage to the drive train of your vehicle and may affect ride, handling, braking and speedometer/odometer calibra- tion. It also may be dangerous and lead to loss of vehicle con- trol. . Do not use a combination of radial, belted bias or bias tires since it may cause dangerous handling characteristics and lead...
Page 307: Loading Your Vehicle
8-12 Driving tips Loading your vehicle WARNING . Never allow passengers to ride on a folded rear seatback or in the cargo area. Doing so may result in serious injury. . Never stack luggage or other cargo higher than the top of the seatback because it could tumble forward and injure passengers in the event of a sudden stop or...
Page 308: Gvwr And Gawr (Gross Vehicle Weight Rating And Gross Axle Weight Rating)
The load capacity of your vehicle is determined by weight, not by available cargo space. The maximum load you can carry in your vehicle is shown on the vehicle placard attached to the driver’s side door pillar. It includes the total weight of the driver and all passengers and their belongings, any optional equipment such as a trailer hitch, roof rack or bike carrier,...
Page 309: Roof Rail (If Equipped)
8-14 Driving tips & Roof rail (if equipped) Roof rack Luggage can be carried on the roof after securing the roof rack to the roof rail. When installing the roof rack on the roof rail, follow the manufacturer’s instructions. The roof rail is designed to carry loads (luggage and roof rack) of not more than 150 lbs (68 kg).
Page 310 Cargo can be carried after securing the roof crossbar kit to the roof molding and installing the appropriate carrying attach- ment. When installing the roof crossbar kit, follow the manufacturer’s instructions. When you carry cargo on the roof using the roof crossbar kit and a carrying attachment, never exceed the maximum load limit as explained below.
Page 311: Trailer Hitch (Dealer Option)
. The standard bumper beam must be installed after you remove the trailer hitch. Consult a SUBARU dealer for purchase of a standard bumper beam if you do not have the original.
Page 312: When You Do Not Tow A Trailer
does not come off the hitch receiver. Hitch ball installation point Hooks for safety chains 5. Use only a hitch ball that is appropriate for the ball mount and your trailer. The hitch ball must be securely installed on the ball mount.
Page 313: Trailer Towing
Seek the advice of your SUBARU dealer to assist you in purchasing a hitch and other necessary towing equipment appropriate for your vehicle. In addition, be sure to follow the...
Page 314 Model Conditions Maximum total trailer weight MT models When towing a 1,000 lbs (453 kg) trailer without brakes. When towing a 2,400 lbs trailer with brakes. (1,087 kg) AT models When towing a 1,000 lbs (453 kg) trailer without brakes. When towing a 2,400 lbs trailer with brakes.
Page 315 8-20 Driving tips ! Gross Axle Weight (GAW) and Gross Axle Weight Rating (GAWR) Gross Axle Weight The total weight applied to each axle (GAW) must never exceed the Gross Axle Weight Rating (GAWR). The front and rear GAWs can be adjusted by relocating passengers and luggage inside the vehi- cle.
Page 316: Trailer Hitches
Choose a proper hitch for your vehicle and trailer. The use of a genuine SUBARU trailer hitch is recommended. A genuine SUBARU hitch is available from your SUBARU dealer. If use of a non-genuine hitch is unavoid- able, be sure the hitch is suited to your vehicle and trailer.
Page 317: Connecting A Trailer
Check that your trailer’s brakes conform with Federal, state/province and/ or other applicable regulations. Your SUBARU’s brake system is not designed to be tapped into the trailer’s hydraulic brake system. Please ask your SUBARU dealer and professional trailer supplier for more information about the trailer’s brake...
Page 318: Trailer Towing Tips
To ensure the trailer lights are connected properly, please consult your SUBARU dealer. Check for proper operation of the brake lights and turn signal lights each time you hitch up. ! Tires...
Page 319 . If the ABS warning light illuminates while the vehicle is in motion, stop towing the trailer and have repairs performed immediately by the nearest SUBARU dealer. ! Driving on grades . Before going down a steep hill, slow...
Page 320 “Coolant temperature low indicator light/Coolant temperature high warn- ing light” F3-16. – AT OIL TEMP warning light illumi- nates (AT models). Refer to “AT OIL TEMP warning light (AT models)” F3- . If your vehicle has an automatic trans- mission, avoid using the accelerator pedal to stay stationary on an uphill slope instead of using the parking brake or foot brake.
Page 321 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 322: In Case Of Emergency
If you park your vehicle in case of an emergency ... Temporary spare tire (if equipped) ... Precautions for AWD models with automatic transmission ... Maintenance tools ... Tool bag... Under the cargo area... Flat tires... Changing a flat tire... Tire pressure monitoring system (TPMS) (U.S.-spec.
Page 323: If You Park Your Vehicle In Case Of An Emergency
This indicates the tire pressure monitoring system (TPMS) is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/or sys- tem resetting.
Page 324: Precautions For Awd Models With Automatic Transmission
install the conventional tire as soon as possible because the spare tire is de- signed only for temporary use. Check the inflation pressure of the tem- porary spare tire periodically to keep the tire ready for use. The correct pressure is 60 psi (420 kPa, 4.2 kg/cm When using the temporary spare tire, note the following.
Page 325: Maintenance Tools
In case of emergency Spare fuse FWD connector 3. Put a spare fuse inside the FWD connector located in the cabin and confirm that the All-Wheel Drive warning light “ ” illuminates. The All-Wheel-Drive capability of the vehicle has now been deactivated.
Page 326: Under The Cargo Area
& Under the cargo area Under-floor storage compartment (if equipped) (Refer to “Under-floor storage compartment” F6-16) Jack handle Tool bucket Spare tire Wheel nut wrench Hex-head wrench (only models with moonroof) Screwdriver Jack Towing hook (eye bolt) The jack handle is stored under the cargo In case of emergency floor.
Page 327: Flat Tires
In case of emergency Flat tires If you have a flat tire while driving, never brake suddenly; keep driving straight ahead while gradually reducing speed. Then slowly pull off the road to a safe place. & Changing a flat tire WARNING .
Page 328 Models with temporary spare tire 6. Take out the tool bucket and turn the attaching bolt counterclockwise, then take the spare tire out. NOTE If the spare tire provided in your vehicle is a temporary spare tire, carefully read “Temporary spare tire” F9-2 and strictly follow the instructions.
Page 329 In case of emergency 10. Insert the jack handle into the jack- screw, and turn the handle until the tire clears the ground. Do not raise the vehicle higher than necessary. 11. Remove the wheel nuts and the flat tire. 12.
Page 330: Tire Pressure Monitoring System (Tpms) (U.s.-Spec. Models)
16. Store the flat tire in the spare tire compartment. Put in the spacer and tight- en the attaching bolt firmly. Also store the jack, jack handle and wheel nut wrench in their storage locations. WARNING Never place a tire or tire changing tools in the passenger compartment after changing wheels.
Page 331: Jump Starting
This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. Do not inject any tire liquid or...
Page 332: How To Jump Start
9-11 In case of emergency & How to jump start 1. Make sure the booster battery is 12 volts and the negative terminal is grounded. 2. If the booster battery is in another vehicle, do not let the two vehicles touch. 3.
Page 333 9-12 In case of emergency (1) Connect one jumper cable to the positive (+) terminal on the discharged battery. (2) Connect the other end of the jumper cable to the positive (+) term- inal of the booster battery. (3) Connect one end of the other cable to the negative (−) terminal of the booster battery.
Page 334: Engine Overheating
Engine overheating WARNING Never attempt to remove the radia- tor cap until the engine has been shut off and has fully cooled down. When the engine is hot, the coolant is under pressure. Removing the cap while the engine is still hot could release a spray of boiling hot coolant, which could burn you very seriously.
Page 335: Towing
9-14 In case of emergency Towing If towing is necessary, it is best done by your SUBARU dealer or a commercial towing service. Observe the following procedures for safety. WARNING Never tow AWD models (both AT and MT) with the front wheels raised off...
Page 336 To install the rear towing hook, the standard bumper beam must be installed on the vehicle at a SUBARU dealer. Consult a SUBARU dealer for details. Use a hitch ball and follow the instructions below when towing. . The weight of the object being towed must be less than the weight of the vehicle.
Page 337 9-16 In case of emergency 4. Tighten the towing hook securely using a wheel nut wrench. After towing, remove the towing hook from the vehicle and stow it in the tool bucket. Fit the towing hook cover on the bumper. WARNING Do not use the towing hook except when towing your vehicle.
Page 338: Using A Flat-Bed Truck
& Using a flat-bed truck This is the best way to transport your vehicle. Use the following procedures to ensure safe transportation. 1. Shift the select lever into the “P” position for automatic transmission mod- els or “1st” for manual transmission models.
Page 339: Opened
9-18 In case of emergency distances, transport your vehicle on a flat-bed truck. Rear gate – if the rear gate cannot be opened In the event that you cannot open the rear gate by operating the power door locking switches or the remote keyless entry system, you can open it from inside the cargo area.
Page 340: Moonroof - If The Moonroof Cannot Be Closed
2. Insert a hex-head wrench in the end of the motor shaft. To close the moonroof, turn the wrench counterclockwise. Have your vehicle checked and repaired by an authorized SUBARU dealer. 9-19 In case of emergency...
Page 341 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 342: Appearance Care
Exterior care ... 10-2 Washing... Waxing and polishing ... Cleaning aluminum wheels ... Corrosion protection... 10-4 Most common causes of corrosion ... To help prevent corrosion... Cleaning the interior... 10-2 Seat fabric ... 10-3 Leather seat materials... 10-4 Synthetic leather upholstery... Climate control panel, audio panel, instrument panel, console panel, and switches ...
Page 343: Exterior Care
10-2 Appearance care Exterior care & Washing CAUTION . When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes.
Page 344: Waxing And Polishing
When in doubt, it is always best to contact your SUBARU dealer or an auto paint specia- list. CAUTION Do not use any agents with organic solvents on the surface of the bulb assembly cover.
Page 345: Cleaning Aluminum Wheels
If any of them are found to be rusted, they should be given an appropriate rust prevention treatment or should be replaced. Contact your SUBARU dealer to perform this kind of maintenance and treatment if you need...
Page 346: Cleaning The Interior
If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading or shrinkage.
Page 347: Synthetic Leather Upholstery
Appearance care & Synthetic leather upholstery The synthetic leather material used on the SUBARU may be cleaned using mild soap or detergent and water, after first vacuum- ing or brushing away loose dirt. Allow the soap to soak in for a few minutes and wipe off with a clean, damp cloth.
Page 348: Maintenance And Service
Maintenance schedule ... Maintenance precautions... Before checking or servicing in the engine compartment... When checking or servicing in the engine compartment (non-turbo models) ... When checking or servicing in the engine compartment while the engine is running... Engine hood ... Engine compartment overview...
Page 349 Maintenance and service Tire pressure monitoring system (TPMS) (U.S.-spec. models) ... Tire inspection ... Tire pressures and wear ... Wheel balance... Wear indicators ... Tire rotation direction mark ... Tire rotation ... Tire replacement ... Wheel replacement... Wheel covers (if equipped) ... Aluminum wheels...
Page 350: Maintenance Schedule
Maintenance precautions When maintenance and service are re- quired, it is recommended that all work be done by an authorized SUBARU dealer. If you perform maintenance and service by yourself, you should familiarize yourself with the information provided in this section on general maintenance and service for your SUBARU.
Page 351: Before Checking Or Servicing In The Engine Compartment
NEVER use a circuit tester for this wiring. If your SRS airbag or seatbelt preten- sioner needs service, consult your nearest SUBARU dealer. & Before checking or servicing in the engine compartment WARNING . Always stop the engine and set the parking brake firmly to pre- vent the vehicle from moving.
Page 352: When Checking Or Servicing In The Engine Compartment While The Engine Is Running
the engine has stopped. & When checking or servicing in the engine compartment while the engine is running WARNING A running engine can be dangerous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other moving engine parts.
Page 353 11-6 Maintenance and service WARNING Always check that the hood is properly locked before you start driving. If it is not, it might fly open while the vehicle is moving and block your view, which may cause an accident and serious bodily in- jury.
Page 354: Fuse Box (Page
Engine compartment overview & Non-turbo models 11-7 Maintenance and service Power steering fluid reservoir (page 11- Manual transmission oil level gauge (MT) (page 11-20) or Differential gear oil level gauge (AT) (page 11-22) Clutch fluid reservoir (page 11-26) Automatic transmission fluid level gauge (page 11-21) Brake fluid reservoir (page 11-25) Fuse box (page 11-45)
Page 355: Turbo Models
11-8 Maintenance and service & Turbo models Power steering fluid reservoir (page 11-24) Differential gear oil level gauge (AT) (page 11-22) Clutch fluid reservoir (page 11-26) Automatic transmission fluid level gauge (page 11-21) Brake fluid reservoir (page 11-25) Fuse box (page 11-45) Battery (page 11-44) Windshield washer tank (page 11-38) Engine oil filler cap (page 11-9)
Page 356: Engine Oil
. If the oil consumption rate seems abnormally high after the break-in period, for example more than 1 quart per 1,200 miles or 1 liter per 2,000 kilometers, contact your SUBARU deal- & Checking the oil level Check the engine oil level at each fuel stop.
Page 357: Changing The Oil And Oil Filter
11-10 Maintenance and service Turbo models Notch Upper level Lower level Approximately 1.1 US qt (1.0 liter, 0.9 Imp qt) from lower level to upper level Non-turbo models Upper level Lower level Approximately 1.1 US qt (1.0 liter, 0.9 Imp qt) from lower level to upper level 4.
Page 358 SUBARU dealer. 1. Warm up the engine by letting the engine idle for approximately 10 minutes to ease draining the engine oil. 2. Park the vehicle on a level surface and stop the engine. 3. Remove the oil filler cap.
Page 359: Recommended Grade And Viscosity
11-12 Maintenance and service 9. Clean the rubber seal seating area of the bottom of engine and install the oil filter by hand turning. Be careful not to twist or damage the seal. 10. Tighten the oil filter by the amount indicated in the following table after the seal makes contact with the bottom of engine.
Page 360: Synthetic Oil
, u s e o n l y SUBARU Super Coolant. If the SUBARU Super Coolant is diluted with another brand or type, the maintenance interval is...
Page 361: Engine Coolant
Always add genuine SUBARU cooling system conditioner whenever the coolant is replaced. Change the engine coolant and add genuine SUBARU cooling system condi- tioner using the following procedures according to the maintenance schedule.
Page 362 5. Slowly pour the coolant and fill up to just below the filler neck, allowing enough 11-15 Maintenance and service room to add genuine SUBARU cooling system conditioner in the radiator. Add genuine SUBARU cooling system condi- tioner until the coolant level reaches the filler neck.
Page 363: Air Cleaner Element
CAUTION When replacing the air cleaner ele- ment, use a genuine SUBARU air cleaner element. If it is not used, there is the possibility of causing a negative effect to the engine.
Page 364: Replacing The Air Cleaner Element
Replace the air cleaner element according to the maintenance schedule in the “Warranty and Maintenance Booklet”. Un- der extremely dusty conditions, replace it more frequently. It is recommended that you always use genuine SUBARU parts. ! Non-turbo models Connector Clip Clamp...
Page 365 11-18 Maintenance and service ! Turbo models 1. Use a screwdriver to undo the clips on the air intake duct, then remove the air intake duct. Connector Clip 2. Unplug the connector that is attached to the top of the air cleaner case. 3.
Page 366: Spark Plugs
(98 N, 10 kgf) midway between the pulleys by using a spring scale. The belt deflec- tion should be the amount specified. If the front side belt is loose, cracked or worn, contact your SUBARU dealer. in (mm) Deflection New belt Used belt 0.28 –...
Page 367: Non-Turbo Models
However, replacement of the belt should be done according to the maintenance schedule in the “Warranty and Maintenance Booklet”. Consult your SUBARU dealer for replacement. If the belt is loose, cracked or worn, contact your SUBARU dealer. Manual transmission oil &...
Page 368: Recommended Grade And Viscosity
& Recommended grade and viscosity Each oil manufacturer has its own base oils and additives. Never use different brands together. For details, refer to “Manual transmission, front differential and rear differential gear oil” F12-8. Automatic transmission fluid & Checking the fluid level The automatic transmission fluid expands largely as its temperature rises;...
Page 369: Recommended Fluid
11-22 Maintenance and service fluid level on the gauge. If it is below the lower level on the “HOT” range, add the recommended automatic transmission fluid up to the upper level. ! Checking the fluid level when the fluid is cold When the fluid level has to be checked without time to warm up the automatic transmission, check to see that the fluid...
Page 370: Recommended Grade And Viscosity
Maintenance and service Rear differential gear oil There is no rear differential gear oil level gauge. To check the rear differential gear oil level, consult your SUBARU dealer for inspection. & Recommended grade and viscosity Each oil manufacturer has its own base oils and additives.
Page 371: Power Steering Fluid
“MIN” and “MAX” line. If the fluid level is extremely low, it may indicate possible leakage. Consult your SUBARU dealer for an inspection. WARNING Be careful not to burn yourself because the fluid may be hot.
Page 372: Brake Fluid
. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. CAUTION . When adding brake fluid, be care- ful not to allow any dirt into the reservoir.
Page 373: Clutch Fluid (Mt Models)
. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. . When clutch fluid is added, be careful not to allow any dirt into the tank.
Page 374: Brake Booster
Lightly pull the brake pedal up with one finger to check the free play with a force of less than 2 lbf (10 N, 1 kgf). If the free play is not within proper specification, contact your SUBARU deal- – CONTINUED –...
Page 375: Checking The Brake Pedal Reserve Distance
0.16 – 0.43 in (4.0 – 11.0 mm) Lightly press the clutch pedal down with your finger until you feel resistance, and check the free play. If the free play is not within proper specification, contact your SUBARU deal-...
Page 376: Hill Start Assist System (Mt Models)
If you hear this scraping noise each time you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as possible. CAUTION If you continue to drive despite the...
Page 377: Parking Brake Stroke
N, 20.4 kgf]). If the parking brake lever stroke is not within the specified range, have the brake system checked and adjusted at your SUBARU dealer. Tires and wheels & Types of tires You should be familiar with type of tires present on your vehicle.
Page 378: Tire Pressure Monitoring System (Tpms) (U.s.-Spec. Models)
In this event, go to a SUBARU dealer to have the system inspected as soon as possible. While the vehicle is driven, friction be- tween tires and the road surface causes the tires to warm up.
Page 379: Tire Inspection
Tire Pressure Monitoring System checked at a SUBARU dealer as soon as possi- ble. If this light illuminates while driving, never brake suddenly and keep driving straight ahead while gradu- ally reducing speed.
Page 380: Tire Pressures And Wear
Drive slowly to the nearest authorized SUBARU dealer and have the vehicle inspected. & Tire pressures and wear Maintaining the correct tire pressures helps to maximize the tires’...
Page 381 11-34 Maintenance and service . Correct tire pressure (tread worn evenly) Roadholding is good, and steering is responsive. Rolling resistance is low, so fuel consumption is also lower. . Abnormally low tire pressure (tread worn at shoulders) Rolling resistance is high, so fuel con- sumption is also higher.
Page 382: Wheel Balance
If you suspect that the wheels are not correctly balanced, have them checked and adjusted by your SUBARU dealer. Also have them adjusted after tire repairs and after tire rotation. NOTE...
Page 383: Tire Rotation
(tread pattern), con- struction, and size. You are advised to replace the tires with new ones that are identical to those fitted as standard equip- ment. For safe vehicle operation, SUBARU recommends replacing all four tires at the same time.
Page 384: Wheel Replacement
Replacement wheels are available from SUBARU dealers. WARNING Use only those wheels that are specified for your vehicle. Wheels not meeting specifications could...
Page 385: Aluminum Wheels
. Never let the wheel rub against sharp protrusions or curbs. . When wheel nuts, balance weights, or the center cap is replaced, be sure to replace them with genuine SUBARU parts designed for aluminum wheels. Windshield washer fluid If you spray washer fluid on the windshield...
Page 386 In areas where water freezes in winter, use an anti-freeze type windshield washer fluid. SUBARU Windshield Washer Fluid contains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing tem- perature varies according to how much it is diluted, as indicated in the following table.
Page 387: Replacement Of Wiper Blades
11-40 Maintenance and service Replacement of wiper blades Grease, wax, insects, or other material on the windshield or the wiper blade results in jerky wiper operation and streaking on the glass. If you cannot remove the streaks after operating the windshield washer or if the wiper operation is jerky, clean the outer surface of the windshield (or rear window) and the wiper blades using a...
Page 388: Windshield Wiper Blade Rubber
& Windshield wiper blade rub- Support 1. Grasp the locked end of the blade rubber assembly and pull it firmly until the stoppers on the rubber are free of the support. Metal spines 2. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber.
Page 389: Rear Window Wiper Blade Assembly
11-42 Maintenance and service & Rear window wiper blade assembly 1. Raise the wiper arm off the rear window. 2. Turn the wiper blade assembly coun- terclockwise. 3. Pull the wiper blade assembly toward you to remove it from the wiper arm. 4.
Page 390 2. Pull the blade rubber assembly out of the plastic support. Metal spines 3. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber. 4.
Page 391: Battery
11-44 Maintenance and service Battery WARNING . Before beginning work on or near any battery, be sure to extinguish all cigarettes, matches, and light- ers. Never expose a battery to an open flame or electric sparks. Batteries give off a gas which is highly flammable and explosive.
Page 392: Fuses
Fuses CAUTION Never replace a fuse with one hav- ing a higher rating or with material other than a fuse because serious damage or a fire could result. The fuses are designed to melt during an overload to prevent damage to the wiring harness and electrical equipment.
Page 393: Main Fuse
6. If the same fuse blows again, this indicates that its system has a problem. Contact your SUBARU dealer for repairs. Main fuse Main fuse box The main fuses are designed to melt...
Page 394: Replacing Bulbs
11-47 Maintenance and service NOTE . If headlight aiming is required, con- sult your SUBARU dealer for proper adjustment of the headlight aim. . It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary.
Page 395 11-48 Maintenance and service ! Low beam light bulbs Right-hand side 1. Use a screwdriver to undo the clips on the air intake duct, then remove the air intake duct (right-hand side). Left-hand side 2. Use a screwdriver to remove the secured clip of the washer tank.
Page 396: Position Light
7. To install the bulb to the headlight assembly, turn it clockwise until it clicks. 8. Reconnect the electrical connector. 9. Install the bulb cover. 10. Install the air intake duct with clips (right-hand side). 11. Set the washer tank to the original place and secure it by clip (left-hand side).
Page 397: Front Turn Signal Light
11-50 Maintenance and service & Front turn signal light It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary. & Rear combination lights 1. Using a Phillips screwdriver, remove the upper and lower screws that secure the rear combination light assembly.
Page 398: License Plate Light
7. Tighten the upper and lower screws. & License plate light 1. Remove the mounting screws using a Phillips screwdriver. 2. Remove the cover and lens. 3. Pull the bulb out of the socket. 4. Install a new bulb. 5. Reinstall the lens and cover. 6.
Page 399: Other Bulbs
2. Pull the bulb out of the socket. 3. Install a new bulb. 4. Reinstall the lens. & Other bulbs It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary.
Page 400 Specifications ... 12-2 Dimensions... Engine ... Electrical system... Fuel ... Engine oil ... Manual transmission, front differential and rear differential gear oil ... Fluids ... Engine coolant ... Tires... Wheel alignment ... 12-2 Fuses and circuits ... 12-3 12-3 Fuse panel located in the passenger compartment ...
Page 401: Specifications
12-2 Specifications Specifications These specifications are subject to change without notice. & Dimensions Item Overall length Overall width Overall height without roof rail with roof rail Wheel base Tread Front Rear Ground clearance* *1: Measured with vehicle empty Non-turbo models Turbo models 179.5 (4,560) 70.1 (1,780)
Page 402: Engine
& Engine Engine model Engine type Displacement cc (cu-in) Bore 6 Stroke in (mm) Compression ratio Firing order & Electrical system Battery type and capacity (5HR) Alternator Spark plugs Non-turbo engine Turbo engine AT: Automatic transmission MT: Manual transmission FB25B (2.5-liter, DOHC, non-turbo) Horizontally opposed, liquid cooled 4 cylinder, 4-stroke gasoline engine 2,498 (152)
Page 403: Fuel
12-4 Specifications & Fuel NOTE The engine is designed to operate using unleaded gasoline. Model Fuel requirement Fuel tank capacity Non-turbo 87 AKI (90 RON) or higher 16.9 US gal (64 liters, 14.1 Imp gal) 91 AKI (95 RON) or higher* Turbo *1: If unleaded gasoline with an octane rating of 91 AKI (95 RON) is not available, unleaded gasoline with an octane rating of 87 AKI (90 RON) or higher may be temporarily used.
Page 404: Engine Oil
SUBARU dealer. ! Approved engine oil Always use the SUBARU approved engine oil. For further details, please contact your SUBARU dealer. If the approved engine oil is unavailable, use the alternative engine oil described on the next page.
Page 405 12-6 Specifications ! Alternative engine oil If the SUBARU approved oil is unavailable, the following alternative oil can be used. NOTE Each quantity indicated here is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other factors.
Page 406 ! Turbo models Oil grade API classification SM or SN with ILSAC GF-4 or GF-5, which can the words be identified with the ILSAC “ENERGY CONSERVING” or certification mark (Starburst “RESOURCE CONSERVING” mark) SAE viscosity No. and applicable temperature – Adding the oil from L to F level: 5W-30 synthetic oil is required for 1.1 US qt (1.0 liter, 0.9 Imp qt) optimum engine performance and pro-...
Page 407: Manual Transmission, Front Differential And Rear Differential Gear Oil
12-8 Specifications & Manual transmission, front differential and rear differential gear oil Oil grade Manual transmission Front differential (AT models) API classification GL-5 Rear differential For the checking procedure, or other details, refer to “Manual transmission oil” F11-20, “Front differential gear oil (AT models)” F11-22, “Rear differential gear oil”...
Page 408: Fluids
Automatic transmission Turbo For the checking, adding and replacing procedure, or other details, refer to “Cooling system” F11-13. Fluid type · SUBARU ATF · IDEMITSU ATF HP · SUBARU ATF · IDEMITSU ATF HP · “Dexron III” Type Automatic Transmission Fluid FMVSS No.
Page 409: Specifications
12-10 Specifications & Tires Tire size Wheel size Pressure Front Rear Rear when towing trailer Temporary Size spare tire Pressure Wheel nut tightening torque *: This torque is equivalent to applying approximately 88 to 110 lbf (40 to 50 kgf) at the edge of the wheel nut wrench. If you have tightened the wheel nuts by yourself, have the tightening torque checked at the nearest automotive service facility as soon as possible.
Page 410: Fuses And Circuits
Fuses and circuits & Fuse panel located in the passenger compartment 12-11 Specifications Fuse Fuse Circuit panel rating Trailer Empty Door locking Front wiper deicer relay Combination meter 7.5A Remote control rear view mirrors Seat heater relay Combination meter Integrated unit Stop light Front wiper deicer 7.5A...
Page 411 12-12 Specifications Fuse Fuse Circuit panel rating Illumination Seat heaters Back-up light Empty Accessory power outlet (instrument panel) 7.5A Starter relay Air conditioner Rear window defogger relay coil Rear wiper Rear window washer Audio unit Clock SRS airbag system 7.5A Power window relay Radiator main fan relay Tail and illumination re-...
Page 412: Fuse Panel Located In The Engine Compartment
& Fuse panel located in the engine compartment Main fuse 12-13 Specifications Fuse Fuse Circuit panel rating ABS unit Vehicle Dynamics Con- trol unit Main fan (cooling fan) Secondary air combina- tion valve (turbo models) Sub fan (cooling fan) Empty Audio Headlight (low beam) Headlight (high beam)
Page 413 12-14 Specifications Fuse Fuse Circuit panel rating Headlight (right hand) Headlight (left hand)
Page 414: Bulb Chart
12-15 Specifications Bulb chart Lights A and B are the LED (Light Emitting Diode) type. Consult your SUBARU dealer for replacement. – CONTINUED –...
Page 415 – Do not replace any headlight bulbs (both low beam and high beam) by yourself. – Do not remove/restore the headlight assemblies by your- self. – Do not remove any headlight- assembly components by yourself. For replacement, contact your SUBARU dealer.
Page 416 12-17 Specifications CAUTION Replace any bulb only with a new bulb of the specified wattage. Using a bulb of different wattage could result in a fire.
Page 417: Vehicle Identification
12-18 Specifications Vehicle identification Vehicle identification number Emission control label Tire inflation pressure label Certification label Vehicle identification number plate Model number label Fuel label Air conditioner label...
Page 418 Consumer information and Reporting safety defects For U.S.A..13-2 Tire information ... 13-2 Tire labeling ... Recommended tire inflation pressure... Glossary of tire terminology ... Tire care – maintenance and safety practices... Vehicle load limit – how to determine... Determining compatibility of tire and vehicle load capacities ...
Page 419: Consumer Information And Reporting Safety Defects
13-2 Consumer information and Reporting safety defects For U.S.A. The following information has been compiled according to Code of Federal Regulations “Title 49, Part 575”. Tire information & Tire labeling Many markings (e.g. Tire size, Tire Identification Number or TIN) are placed on the sidewall of a tire by tire manufacturers.
Page 420 Example: (6) Load Index: A numerical code which specifies the maximum load a tire can carry at the speed indicated by its speed symbol, at maximum inflation pressure. For example, “90” means 1,323 lbs (600 kg), “89” means 1,278 lbs (580 kg).
Page 421: Recommended Tire Inflation Pressure
13-4 Consumer information and Reporting safety defects ! Maximum load rating The load rating at the maximum permissible weight load for this tire. For example, “MAX. LOAD 580 kg (1279 LBS) @ 300 kPa (44 PSI) MAX. PRESS.” WARNING Maximum load rating applies only to the tire, not to the vehicle.
Page 422: Glossary Of Tire Terminology
crease in temperature could cause tread separation, and failure of the tire(s). Possible resulting loss of vehicle control could lead to an accident. ! Measuring and adjusting air pressure to achieve proper in- flation Check and, if necessary, adjust the pressure of each tire (including the spare) at least once a month and before any long journey.
Page 423 13-6 Consumer information and Reporting safety defects Extra load tire A tire designed to operate at higher loads and higher inflation pressure than the corresponding standard tire. Groove The space between two adjacent tread ribs. Innerliner The layer(s) forming the inside sur- face of a tubeless tire that contains the inflating medium within the tire.
Page 424 Passenger car tire A tire intended for use on passen- ger cars, multipurpose passenger vehicles, and trucks, that have a gross vehicle weight rating (GVWR) of 10,000 lbs (4,535 kg) or less. A layer of rubber-coated parallel cords. Ply separation A parting of rubber compound between adjacent plies.
Page 425 13-8 Consumer information and Reporting safety defects Tread rib A tread section running circumfer- entially around a tire. Tread separation Pulling away of the tread from the tire carcass. Treadwear indicators (TWI) The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread.
Page 426: Tire Care - Maintenance And Safety Practices
Table 1 — Occupant loading and distribution for vehicle normal load for various designated seating capacities Designated seating Vehicle normal load, capacity, number of number of occupants occupants 2 through 4 5 through 10 11 through 15 16 through 22 Consumer information and Reporting safety defects Occupant distribution in a normally loaded vehicle...
Page 427: Vehicle Load Limit - How To Determine
13-10 Consumer information and Reporting safety defects Replace any damaged or un- evenly worn tires at the time of rotation. After tire rotation, adjust the tire pressures and make sure the wheel nuts are correctly tigh- tened. For information about the tightening torque and tightening sequence for the wheel nuts, refer to “Flat tires”...
Page 428 Calculate the total weight. Calculate the available load ca- pacity by subtracting the total weight from the vehicle capacity weight of 900 lbs (408 kg). The result of step 2 shows that a further 84 lbs (38 kg) of cargo can be carried.
Page 429 13-12 Consumer information and Reporting safety defects with the statement “The combined weight of occupants and cargo should never exceed 408 kg or 900 lbs”. For example, the vehicle has one occupant weighing 165 lbs (75 kg) plus cargo weighing 375 lbs (170 kg).
Page 430: Determining Compatibility Of Tire And Vehicle Load Capacities
The total weight now exceeds the capacity weight by 32 lbs (15 kg), so the cargo weight must be reduced by 32 lbs (15 kg) or more. & Determining compatibility of tire and vehicle load capaci- ties The sum of four tires’ maximum load ratings must exceed the max- imum loaded vehicle weight (“GVWR”).
Page 431: Uniform Tire Quality Grading Standards
13-14 Consumer information and Reporting safety defects able cargo and luggage load capa- city is 650 lbs. (1,400 − 750 (5 6 150) = 650 lbs) Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calcu- lated in step 4.
Page 432: Temperature A, B, C
However, NHTSA cannot become involved in individual problems between you, your dealer, or Subaru of America, Inc. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov;...
Page 433 13-16 Consumer information and Reporting safety defects Building, Washington, DC 20590. You can also obtain other informa- tion about motor vehicle safety from http://www.safercar.gov.
Page 434: Index
Index...
Page 435 14-2 Index ABS (Anti-lock Brake System) ... 7-23 Warning light ... 3-19 Accessories... 5-4, 11-46 Accessory power outlet... 6-9 Active head restraint... 1-6 Air cleaner element ... 11-16 Air conditioner Manual climate control system... 4-7 Air filtration system... 4-18 Airflow selection Automatic climate control system ...
Page 436 Parking ... 7-29, 11-30 Pedal ... 11-27 System ... 7-22 Brake pedal Free play ... 11-27 Reserve distance ... 11-28 Brake system ... 7-22 Warning light ... 3-20 Braking ... 7-22 Tips... 7-22 Breaking-in of new brake pads and linings ... 11-29 Bulb Chart ...
Page 437 14-4 Index Climate control system Automatic... 4-8 Manual ... 4-3 Clock... 3-25 Clutch Fluid... 11-26, 12-9 Pedal ... 11-28 Coat hook ... 6-13 Coin tray... 6-7 Compass ... 3-37, 3-38 Continuously variable transmission Fluid... 12-9 Coolant... 11-14, 12-9 Temperature high warning light ... 3-16 Temperature low indicator light...
Page 438 Hood ... 11-5 Oil... 11-9, 12-5 Overheating ... 9-13 Starting... 7-7 Stopping ... 7-9 Exterior care... 10-2 Flat tires ... 9-6 Floor mat ... 6-12 Fluid level Automatic transmission ... 11-21 Brake ... 11-25 Clutch... 11-26 Power steering ... 11-24 Fog light Indicator light...
Page 439 14-6 Index Hill start assist (MT models) ... 7-31, 11-29 Warning light ... 3-21 HomeLink ... 3-38 ® Hook Cargo tie-down ... 6-15 Coat ... 6-13 Shopping bag ... 6-13 Towing and tie-down... 9-14 Horn... 3-47 Hose and connections ... 11-13 Ignition switch...
Page 440 Rear combination... 11-50 Turn signal ... 3-31, 11-50 Loading your vehicle ... 8-12 Low fuel warning light ... 3-11, 3-21 Low tire pressure warning light ... 3-18 Lower and tether anchorage... 1-29 Main fuse... 11-46 Maintenance Precautions ... 11-3 Schedule ... 11-3 Seatbelt ...
Page 441 14-8 Index Preparing to drive ... 7-7 Rear Combination lights... 11-50 Differential gear oil ... 11-23, 12-8 Gate... 2-23, 9-18 Turn signal light ... 11-50 Rear seat... 1-7 Center table ... 6-7 Folding down... 1-10 Reclining... 1-10 Rear view camera ... 6-17 Rear window Defogger...
Page 442 Heater ... 1-6 Height adjustment ... 1-4 Power... 1-4 Rear... 1-7 Seatbelt ... 5, 1-12 Fastening... 1-13 Maintenance... 1-19 Pretensioners ... 1-20 Safety tips... 1-12 Warning light and chime ... 3-13 Security Alarm system ... 2-15 ID plate... 2-3 Immobilizer... 2-2 Indicator light...
Page 443 14-10 Index Pressures and wear ... 11-33 Replacement ... 11-36 Rotation ... 11-36 Size and pressure ... 12-10 Types ... 11-30 Tire pressure monitoring system (TPMS)... 7-28, 9-9, 11-31 Warning light ... 3-18 Tires and wheels... 11-30 Tools ... 9-4 Top tether anchorages ...
Page 444 Seatbelt ... 3-13 SRS airbag system ... 3-15 Vehicle Dynamics Control ... 3-22 Warranties ... 1 Warranties and maintenance ... 8-18 Washing ... 10-2 Waxing and polishing ... 10-3 Wear indicators... 11-35 Wheel Alignment... 12-10 Aluminum... 11-38 Balance ... 11-35 Covers...
Page 445 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 446 Fuel capacity: 16.9 US gal (64 liters, 14.1 Imp gal) & Engine oil: Use SUBARU approved motor oil or equivalent. For the details, refer to “Engine oil” F12-5. & Engine oil capacity: Non-turbo models: 5.5 US qt (5.2 liters, 4.6 Imp qt) Turbo models: 4.4 US qt (4.2 liters, 3.7 Imp qt)

This manual is also suitable for:

Forester 2011

Subaru 2011 Forester Owner's Manual

Table of Contents

Table of Contents

Front Seats

Seat Heater (if Equipped)

Rear Seats

Seatbelts

Front Seatbelt Pretensioners

Child Restraint Systems

SRS Airbag (Supplemental Restraint System Airbag)

Keys and Doors

Keys

Immobilizer

Door Locks

Power Door Locking Switches

Remote Keyless Entry System

Alarm System

Child Safety Locks

Windows

Rear Gate

Moonroof (if Equipped)

Instruments and Controls

Climate Control

Ventilator

Manual Climate Control System (if Equipped)

Automatic Climate Control System (if Equipped)

! Control Panel

Operating Tips for Heater and Air Conditioner

Air Filtration System

Audio

Antenna System

Audio Set

Installation of Accessories

Power and Audio Controls

FM/AM Radio Operation

Satellite Radio Operation (if Equipped)

CD Player Operation

Auxiliary Input Jack (if Equipped)

Precautions to Observe When Handling a Compact Disc

Audio Control Buttons (if Equipped)

Bluetooth ® Audio Operation

Hands-Free System (if Equipped)

Screensaver (Type D Audio)

Interior Equipment

Quick Links

Chapters

Related Manuals for Subaru 2011 Forester

Summary of Contents for Subaru 2011 Forester